2764444 BEARING AS-IDLER Caterpillar parts
PR190
Rating:
Alternative (cross code) number:
CA2764444
276-4444
2764444
CA2764444
276-4444
2764444
Weight: 3 pounds 1 kg.
RAKE-POWER BOX,
This part in 10 request:
Show.
This information for suppliers only!
2025-09-25
2023-12-22
2023-01-31
2022-08-22
2022-08-16
2022-08-01
2022-08-01
2022-07-20
2021-11-03
2021-10-25
Compatible equipment models: 2764444:
Number on catalog scheme:
9
For full view, you need register
Information:
Removal Procedure
Start By:
Connect the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame Lock - Separate and Connect" for the machine that is being serviced.
Release the pressure in the hydraulic system. Refer to Disassembly and Assembly, "Hydraulic System Pressure - Release" for the machine that is being serviced.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Personal injury can result from hydraulic oil pressure and hot oil.Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system.Make sure all of the attachments have been lowered, oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.
Note: Put identification marks on all lines, on all hoses, on all wires, and on all tubes for installation purposes. Plug all lines, hoses, and tubes. This helps to prevent fluid loss and this helps to keep contaminants from entering the system.
Illustration 1 g00655574
Open access door (1) behind the cab.
Illustration 2 g00747561
Remove four bolts (2) and the washers.
Disconnect tube (3) .
Disconnect two hoses (4) from gear pump (5) .
Illustration 3 g00747562
Attach a suitable hoist and a suitable lifting sling to gear pump (5), as shown.
Remove two mounting bolts (6) and the washers.
Use the hoist in order to remove gear pump (5). The weight of gear pump (5) is 67 kg (147 lb).
Start By:
Connect the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame Lock - Separate and Connect" for the machine that is being serviced.
Release the pressure in the hydraulic system. Refer to Disassembly and Assembly, "Hydraulic System Pressure - Release" for the machine that is being serviced.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Personal injury can result from hydraulic oil pressure and hot oil.Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system.Make sure all of the attachments have been lowered, oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.
Note: Put identification marks on all lines, on all hoses, on all wires, and on all tubes for installation purposes. Plug all lines, hoses, and tubes. This helps to prevent fluid loss and this helps to keep contaminants from entering the system.
Illustration 1 g00655574
Open access door (1) behind the cab.
Illustration 2 g00747561
Remove four bolts (2) and the washers.
Disconnect tube (3) .
Disconnect two hoses (4) from gear pump (5) .
Illustration 3 g00747562
Attach a suitable hoist and a suitable lifting sling to gear pump (5), as shown.
Remove two mounting bolts (6) and the washers.
Use the hoist in order to remove gear pump (5). The weight of gear pump (5) is 67 kg (147 lb).
Caterpillar parts catalog:
Parts bearing Caterpillar catalog:
2764445
BEARING AS
PR190
PR190
2764690
BEARING-CUP
PR190
PR190
2764750
BEARING-CUP
PR190
PR190
2935367
BEARING-SLEEVE
120M, 120M 2, 12M
120M, 120M 2, 12M
2775501
BEARING
12M 2, 140M, 160M, SNOW WING
12M 2, 140M, 160M, SNOW WING
2775495
BEARING
12M 2, 140M, 160M, SNOW WING
12M 2, 140M, 160M, SNOW WING
2773838
BEARING
140M, 160M, SNOW WING
140M, 160M, SNOW WING
2773798
BEARING
12M 2, 140M, 160M, SNOW WING
12M 2, 140M, 160M, SNOW WING
2735461
BEARING
120M, 120M 2, 12M 2, 12M 3 AWD, 140M, 140M 2, 140M 3 AWD, 160M, 160M 2, 160M 3 AWD
120M, 120M 2, 12M 2, 12M 3 AWD, 140M, 140M 2, 140M 3 AWD, 160M, 160M 2, 160M 3 AWD
2822958
BEARING
G107B
G107B
2756079
BEARING
G107B
G107B
2752416
BEARING
G107B
G107B
2764750
BEARING-CUP
PR190
PR190
2764690
BEARING-CUP
PR190
PR190
2764445
BEARING AS
PR190
PR190