2F8084 BEARING Caterpillar parts
120B, 12E
Rating:
Alternative (cross code) number:
CA2F8084
2F-8084
2F8084
CA2F8084
2F-8084
2F8084
Weight: 1 pounds 0 kg.
MOTOR GRADER,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
YNRSP 2F8084 Trust Bearing for Heavy Equipment
YNRSP Brand: YNRSP || Part Number: 2F8084 || Part type: Bearing || Weight: 1.21 lbs (0.55 kg) || Package Contains: 1Pcs x 2F8084
YNRSP Brand: YNRSP || Part Number: 2F8084 || Part type: Bearing || Weight: 1.21 lbs (0.55 kg) || Package Contains: 1Pcs x 2F8084
CTP 2F8084 Trust Bearing for Heavy Equipment
CTP Trust Bearing Only || Sold in each || Easy in-and-out fit
CTP Trust Bearing Only || Sold in each || Easy in-and-out fit
Number on catalog scheme:
None
For full view, you need register
Information:
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 5P-3975 Rubber Lubricant 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g02719461
Illustration 2 g02719579
Ensure that turbocharger (4) is clean and free from damage. Inspect the turbocharger for wear. Refer to System Operation, Testing and Adjusting, "Turbocharger Inspect" for more information. If any part of the turbocharger is worn or damaged, the complete turbocharger must be replaced.
If necessary, test the wastegate actuator for correct operation. Refer to System Operation, Testing and Adjusting, "Turbocharger Inspect". If the wastegate actuator is damaged or the wastegate actuator does not operate within the specified limits, the complete turbocharger must be replaced.
Clean the gasket surfaces of exhaust manifold (16). If necessary, install studs (17) to the exhaust manifold. Tighten the studs to a torque of 18 N m (160 lb in).
Position turbocharger (4) on exhaust manifold (16). Note: Ensure that the turbocharger is correctly oriented.
Install nuts (18). Note: Support the turbocharger as the nuts are installed.
Tighten nuts (18) to a torque of 44 N m (32 lb ft).
Illustration 3 g02719476
Ensure that tube assembly (14) and tube assembly (10) are clean, free from damage and restriction. Replace any damaged components.
Position a new gasket (8) (not shown) and bolts (9) onto tube assembly (14).
Install tube assembly (14) to turbocharger (4). Install bolts (9) finger tight.
Position a new gasket (15) (not shown) between the flange of tube assembly (10) and the cylinder block. Install bolts (13) finger tight.
Tighten bolts (9) and bolts (13) to a torque of 22 N m (195 lb in).
Remove the plug from oil inlet port (19). Refer to Illustration 2. Lubricate the turbocharger bearings with clean engine oil through the oil inlet port. Rotate the wheel of the compressor several times in order to lubricate the bearings.
Use Tooling (A) in order to lubricate a new O-ring seal (12) (not shown). Install O-ring seal (12) (not shown) to tube assembly (10).
Install tube assembly (10) to the cylinder block and position onto turbocharger (4).
Install bolt (11) finger tight. Ensure that tube assembly (10) installed correctly into the cylinder block.
Install banjo bolt (7) and two new sealing washers (6) (not shown) to tube assembly (10).
Tighten banjo bolt (7) to a torque of 20 N m (177 lb in).
Tighten bolt (11) to a torque of 22 N m (195 lb in).
If necessary, install the exhaust elbow. Refer to Disassembly and Assembly, "Exhaust Elbow - Remove and Install" for the correct procedure.
Connect the exhaust outlet tube assembly from the turbocharger, refer to the Original Equipment Manufactures (OEM) for the correct procedure.
If necessary, install the hose assembly to the wastegate actuator on the turbocharger.
Connect tube assembly (5) to turbocharger (4). Tighten hose clamp (3) securely.
Connect hose assembly (1) to turbocharger (4). Tighten hose clamp (2) securely.
Table 1
Required Tools
Tool Part Number Part Description Qty
A 5P-3975 Rubber Lubricant 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g02719461
Illustration 2 g02719579
Ensure that turbocharger (4) is clean and free from damage. Inspect the turbocharger for wear. Refer to System Operation, Testing and Adjusting, "Turbocharger Inspect" for more information. If any part of the turbocharger is worn or damaged, the complete turbocharger must be replaced.
If necessary, test the wastegate actuator for correct operation. Refer to System Operation, Testing and Adjusting, "Turbocharger Inspect". If the wastegate actuator is damaged or the wastegate actuator does not operate within the specified limits, the complete turbocharger must be replaced.
Clean the gasket surfaces of exhaust manifold (16). If necessary, install studs (17) to the exhaust manifold. Tighten the studs to a torque of 18 N m (160 lb in).
Position turbocharger (4) on exhaust manifold (16). Note: Ensure that the turbocharger is correctly oriented.
Install nuts (18). Note: Support the turbocharger as the nuts are installed.
Tighten nuts (18) to a torque of 44 N m (32 lb ft).
Illustration 3 g02719476
Ensure that tube assembly (14) and tube assembly (10) are clean, free from damage and restriction. Replace any damaged components.
Position a new gasket (8) (not shown) and bolts (9) onto tube assembly (14).
Install tube assembly (14) to turbocharger (4). Install bolts (9) finger tight.
Position a new gasket (15) (not shown) between the flange of tube assembly (10) and the cylinder block. Install bolts (13) finger tight.
Tighten bolts (9) and bolts (13) to a torque of 22 N m (195 lb in).
Remove the plug from oil inlet port (19). Refer to Illustration 2. Lubricate the turbocharger bearings with clean engine oil through the oil inlet port. Rotate the wheel of the compressor several times in order to lubricate the bearings.
Use Tooling (A) in order to lubricate a new O-ring seal (12) (not shown). Install O-ring seal (12) (not shown) to tube assembly (10).
Install tube assembly (10) to the cylinder block and position onto turbocharger (4).
Install bolt (11) finger tight. Ensure that tube assembly (10) installed correctly into the cylinder block.
Install banjo bolt (7) and two new sealing washers (6) (not shown) to tube assembly (10).
Tighten banjo bolt (7) to a torque of 20 N m (177 lb in).
Tighten bolt (11) to a torque of 22 N m (195 lb in).
If necessary, install the exhaust elbow. Refer to Disassembly and Assembly, "Exhaust Elbow - Remove and Install" for the correct procedure.
Connect the exhaust outlet tube assembly from the turbocharger, refer to the Original Equipment Manufactures (OEM) for the correct procedure.
If necessary, install the hose assembly to the wastegate actuator on the turbocharger.
Connect tube assembly (5) to turbocharger (4). Tighten hose clamp (3) securely.
Connect hose assembly (1) to turbocharger (4). Tighten hose clamp (2) securely.
Caterpillar parts catalog:
Parts bearing Caterpillar catalog:
12E, 1673, 1674, 955K, 977H, D333A, D334
12E, 651E, 657B, 657E, 657G, 955H, D320A, D330A, D333A
12E, 955H, D320A, D330A, D330B, D4D
120, 120B, 12E, 140, 140B, 14E, 583H, 621, 621B, 627, 627B, D8H
12E, 650B, 666, 666B
12E, 16, 769, 772, 773
120B, 12E, 140, 140B
120B, 12E, 140, 140B
120B, 12E, 12F
120, 120B, 12E, 140, 140B
120, 120B, 12E, 140, 140B
120, 120B, 12F, 140B, 14E
120B, 12E, 140, 140B
6J7997
BEARING
14E
14E
14E, 16
14E, 16
120B, 12E, 140, 140B, 14E
6D6547
BEARING
120G, 12F, 12G, 130G, 14E
120G, 12F, 12G, 130G, 14E
5D7532
BEARING
12F, 14E
12F, 14E
120B, 12E, 12F, 140, 140B, 14E
120, 12F, 14E
120, 120B, 12E, 140, 140B, 14E
120, 120B, 12E, 140, 140B, 14E
12E, 140B, 14E