3332916 BEARING AS Caterpillar parts
320D, 320D FM, 323D SA, 323E L, 324D, 324D L, 324D LN, 324E, 324E L, 324E LN, 325C, 325D, 325D L, 326D L, 329D, 329D L, 329D LN, 329E, 329E L, 329E LN, OEMS
Rating:
Alternative (cross code) number:
CA3332916
333-2916
3332916
CA3332916
333-2916
3332916
Weight: 0.33 pounds 0 kg.
EXCAVATOR, UNDERCARRIAGE,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$80.49
09 Apr 2024
0.1[0.05] Pounds
US: VXB Bearing
VXB Brand 3332916 Needle Bearing Debris Resistant Cage for Caterpillar Parts 3332916
VXB
VXB
$43.13
30 Sep 2021
Amazon.com
CTP 3332916 Needle Bearing Assembly for Models 320D/320D FM/323D SA/323E L/324D/324D L/324D LN Caterpillar
CTP Use for Models 320D/320D FM/323D SA/323E L/324D/324D L/324D LN Caterpillar || Sold in each || Easy in-and-out fit
CTP Use for Models 320D/320D FM/323D SA/323E L/324D/324D L/324D LN Caterpillar || Sold in each || Easy in-and-out fit
$42.03
12 Mar 2019
REPLACEMENT CATERPILLAR: REPLACEMENT CAT
CATERPILLAR 3332916 BEARING AS - NEEDLE NEW
This part in 2 request:
Show.
This information for suppliers only!
2022-12-12
2016-10-19
Number on catalog scheme:
19
For full view, you need register
Compatible equipment models: 3332916:
Information:
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A (1) 256-4866 Seal Protector 1
A (2) 256-4871 Seal Protector 1
( 1 ) C0.5, C0.7, C1.1 and C1.6 engines
( 2 ) C1.5 and C2.2 engines
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
If the front housing is not installed, do not turn the crankshaft. Damage to the engine may occur.
Illustration 1 g01357158
Typical example
Ensure that the assembly of front housing (6) and the nose of the crankshaft are clean and free from damage. Clean the mating surface of plate (5) .
Illustration 2 g01357161
Typical example
Install Tooling (A) on the nose of the crankshaft.
Align pin (2) with hole (X) in oil pump cover (10) . Ensure that the oil pump cover is concentric to idler gear assembly (11) .
Install a new joint to plate (5) .
Guide the linkage for the fuel injection pump into position so that the link is free to move inside the aperture on the cylinder block for the fuel injection pump. Align front housing (6) to the dowels in plate (5) . Install front housing (6) to plate (5) .
Install fasteners (3) and tighten to a torque of 10 N m (89 lb in).
Remove Tooling (A) from the nose of the crankshaft.
Install a new O-ring seal (7) to front housing (6) . Position cover (8) on front housing (6) and install nuts (4) and bolts (9) .
Tighten nuts (4) to a torque of 50 N m (37 lb ft).
If the engine is equipped with a turbocharger, connect the hose to connection (1) .End By:
Install the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley - Remove and Install".
Install the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump - Install".
Table 1
Required Tools
Tool Part Number Part Description Qty
A (1) 256-4866 Seal Protector 1
A (2) 256-4871 Seal Protector 1
( 1 ) C0.5, C0.7, C1.1 and C1.6 engines
( 2 ) C1.5 and C2.2 engines
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
If the front housing is not installed, do not turn the crankshaft. Damage to the engine may occur.
Illustration 1 g01357158
Typical example
Ensure that the assembly of front housing (6) and the nose of the crankshaft are clean and free from damage. Clean the mating surface of plate (5) .
Illustration 2 g01357161
Typical example
Install Tooling (A) on the nose of the crankshaft.
Align pin (2) with hole (X) in oil pump cover (10) . Ensure that the oil pump cover is concentric to idler gear assembly (11) .
Install a new joint to plate (5) .
Guide the linkage for the fuel injection pump into position so that the link is free to move inside the aperture on the cylinder block for the fuel injection pump. Align front housing (6) to the dowels in plate (5) . Install front housing (6) to plate (5) .
Install fasteners (3) and tighten to a torque of 10 N m (89 lb in).
Remove Tooling (A) from the nose of the crankshaft.
Install a new O-ring seal (7) to front housing (6) . Position cover (8) on front housing (6) and install nuts (4) and bolts (9) .
Tighten nuts (4) to a torque of 50 N m (37 lb ft).
If the engine is equipped with a turbocharger, connect the hose to connection (1) .End By:
Install the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley - Remove and Install".
Install the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump - Install".
Cat SIS web machinery list:
Parts bearing Caterpillar catalog:
1290T, 1390, 2491, 2590, 325C, 328D LCR, 330, 330 FM L, 330 L, 330B, 330B L, 330C, 330C FM, 330C L, 330C MH, 330D, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 336E, 336E H, 336E H...
1290T, 1390, 2491, 2590, 325C, 328D LCR, 330B, 330B L, 330C, 330C FM, 330C L, 330C MH, 330D, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 336E, 336E H, 336E HVG, 336E L, 336E LH, 3...
322C, 322C FM, 324D, 324D L, 324D LN
320C, 320C FM, 320D, 320D FM, 320D L, 320D LRR, 320D RR, 321C, 321D LCR
320C, 320C FM, 320C L, 320D, 320D FM, 320D GC, 320D L, 320D LRR, 320D RR, 321C, 321D LCR, 323D L
320C, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 321C, 321D LCR, 323D L, 323D LN, 323D SA
320C, 320D, 320D L, 320E, 320E L, 320E LN, 323D L, 324D, 324D L, 324D LN, 325C, 325C FM, 325D, 325D FM, 325D L, 326D L, 328D LCR, 329D, 329D L, 329D LN, 330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, ...
320D, 320D FM, 323D SA, 323E L, 325C, 325D, 325D L, 328D LCR, 329D, 329D L, 329D LN, 329E, 329E L, 329E LN, 336D, 336D L, 336D LN, 336D2, 336D2 L, 336E, 336E H, 336E HVG, 336E L, 336E LH, 336E LN, 336...
325C, 328D LCR, 330C, 330C FM, 330C L, 330C MH, 330D, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 345B II, 345C, 345C L, 345C MH, 345D, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L, 349E L HVG, ...
325C, 328D LCR, 330C, 330C FM, 330C L, 330C MH, 330D, 330D L, 330D LN, 330D MH
325C, 325D, 325D L, 329D, 329D L, 330C, 330C L, 330D, 330D FM, 330D L, 330D LN, 336D, 336D L, 336D LN, 336D2, 336E L, 340D L, 345C L, 345D, 349D L
325C, 325D
3056286
BEARING
HF201, HF201B, HF221
HF201, HF201B, HF221
3034354
BEARING
HF201, HF201B, HF221
HF201, HF201B, HF221
6V1579
BEARING-TAPERED ROLLER
HF201, HF201B, HF221
HF201, HF201B, HF221
3124344
BEARING-SLEEVE
1190, 1190T, 1290T, 2290, 2390, 2391, 2491, 511, 521, 521B, 522, 522B, 532
1190, 1190T, 1290T, 2290, 2390, 2391, 2491, 511, 521, 521B, 522, 522B, 532
1290T, 1390, 2491, 2590, 330, 330 FM L, 330 L, 330B L, 330D, 345C L, 345D, 349D L, 532, 541, 551, 552, 552 2, OEMS, TK732, TK751, TK752
2290335
BEARING
1190T, 1290T, 2391, 2491, 522, 522B, 532, 552, 552 2, TK722, TK732, TK752
1190T, 1290T, 2391, 2491, 522, 522B, 532, 552, 552 2, TK722, TK732, TK752
1358920
BEARING-IDLER
345B, 345C, 350
345B, 345C, 350
8E4343
BEARING-IDLER
345C, 350
345C, 350
2798107
BEARING-SLEEVE
324D, 324D LN, 324E LN, 325D, 325D L, 329D LN
324D, 324D LN, 324E LN, 325D, 325D L, 329D LN
2797785
BEARING
320D LRR, 321C
320D LRR, 321C
324D, 324D L, 324D LN, 324E, 324E L, 324E LN, 326D L
320D, 320D FM, 323D SA, 323E L, 324D, 324D L, 324D LN, 324E, 324E L, 324E LN, 325C, 325D, 325D L, 326D L, 329D, 329D L, 329D LN, 329E, 329E L, 329E LN, OEMS