3891607 BEARING Caterpillar parts
303.5E, 304E, 305.5E, 305E, 901C, 902C, 903C
Rating:
Alternative (cross code) number:
CA3891607
389-1607
3891607
CA3891607
389-1607
3891607
Weight: 0.55 pounds 0 kg.
COMPACT WHEEL LOADER, MINI HYD EXCAVATOR,
Compatible equipment models: 3891607:
Information:
The CAN Data Link is used for communication between the following modules: engine's Electronic Control Module (ECM), customer devices and various display modules. Two 120 Ohm terminating resistors must be installed in the wiring harness in order for the CAN Data Link to function properly.
Illustration 1 g01027471
Typical example
Test Step 1. Check for Connector Damage.
Turn the Engine Control Switch (ECS) to the OFF position.
Turn the battery disconnect switch to the OFF position.
Thoroughly inspect the primary ECM connectors J1/P1 and J2/P2. Inspect all of the other connectors. Refer to the diagnostic functional test Troubleshooting, "Inspecting Electrical Connectors" for details.
Perform a 45 N (10 lb) pull test on each of the wires in the primary ECM connector that are associated with the circuit.
Check the ECM connectors (allen head screw) for the proper torque of 6 1 N m (53 9 lb in).
Check the harness and the wiring for abrasion and for pinch points. Expected Result:All connectors, pins, and sockets are completely coupled and/or inserted. The harness and wiring are free of corrosion, of abrasion or of pinch points.Results:
OK - The connectors and wiring are okay. Proceed to Test Step 2.
Not OK - The connectors and/or wiring are not okay.Repair: Repair the connectors or wiring and/or replace the connectors or wiring.STOPTest Step 2. Verify Proper Installation of the Terminating Resistors.
Verify that the terminating resistors are installed on the ends of the data link.
Disconnect J1/P1 ECM connector and measure the resistance between P1-50 (CAN Data Link +) and P1-34 (CAN Data Link -). Expected Result:The resistance is between 60 3 Ohms.Results:
OK - The resistance is within the range. Proceed to Test Step 3.
Not OK - The range of the resistance is 120 6 Ohms. A terminating resistor is missing or damaged.Repair: If a termination resistor is missing, install the missing resistor. If both resistors are present, measure the resistance between pin A and pin B of the termination resistor. The resistance should measure 120 3 Ohms. Replace the termination resistor if the resistance is not 120 3 Ohms.Refer to the Schematic in order to determine the missing resistor.Verify that the repair eliminates the problem.STOPTest Step 3. Check for a Short Circuit in the Harness.
Disconnect the J1/P1 ECM connector.
Remove the terminating resistors from the CAN Data Link harness.
If a Marine Power Display (MPD) is installed, disconnect the MPD.
Measure the resistance between the following pins.
P1-50 (CAN Data Link +) and +Battery
P1-34 (CAN Data Link -) and +Battery
P1-50 (CAN Data Link +) to P1-34 (CAN Data Link -)
P1-50 (CAN Data Link +) to P1-42 (CAN Data Link Shield)
P1-34 (CAN Data Link -) to P1-42 (CAN Data Link Shield)
P1-50 (CAN Data Link +) and the −Battery terminalExpected Result:The resistance measures more than 20,000 Ohms.Results:
OK - The resistance is more than 20,000 Ohms. Proceed to Test Step 4.
Not OK - The resistance is less than 20,000 Ohms.Repair: There is a short in the harness wiring. Repair the connectors or wiring and/or replace the connectors or wiring.Verify that the repair eliminates the problem.STOPTest Step
Illustration 1 g01027471
Typical example
Test Step 1. Check for Connector Damage.
Turn the Engine Control Switch (ECS) to the OFF position.
Turn the battery disconnect switch to the OFF position.
Thoroughly inspect the primary ECM connectors J1/P1 and J2/P2. Inspect all of the other connectors. Refer to the diagnostic functional test Troubleshooting, "Inspecting Electrical Connectors" for details.
Perform a 45 N (10 lb) pull test on each of the wires in the primary ECM connector that are associated with the circuit.
Check the ECM connectors (allen head screw) for the proper torque of 6 1 N m (53 9 lb in).
Check the harness and the wiring for abrasion and for pinch points. Expected Result:All connectors, pins, and sockets are completely coupled and/or inserted. The harness and wiring are free of corrosion, of abrasion or of pinch points.Results:
OK - The connectors and wiring are okay. Proceed to Test Step 2.
Not OK - The connectors and/or wiring are not okay.Repair: Repair the connectors or wiring and/or replace the connectors or wiring.STOPTest Step 2. Verify Proper Installation of the Terminating Resistors.
Verify that the terminating resistors are installed on the ends of the data link.
Disconnect J1/P1 ECM connector and measure the resistance between P1-50 (CAN Data Link +) and P1-34 (CAN Data Link -). Expected Result:The resistance is between 60 3 Ohms.Results:
OK - The resistance is within the range. Proceed to Test Step 3.
Not OK - The range of the resistance is 120 6 Ohms. A terminating resistor is missing or damaged.Repair: If a termination resistor is missing, install the missing resistor. If both resistors are present, measure the resistance between pin A and pin B of the termination resistor. The resistance should measure 120 3 Ohms. Replace the termination resistor if the resistance is not 120 3 Ohms.Refer to the Schematic in order to determine the missing resistor.Verify that the repair eliminates the problem.STOPTest Step 3. Check for a Short Circuit in the Harness.
Disconnect the J1/P1 ECM connector.
Remove the terminating resistors from the CAN Data Link harness.
If a Marine Power Display (MPD) is installed, disconnect the MPD.
Measure the resistance between the following pins.
P1-50 (CAN Data Link +) and +Battery
P1-34 (CAN Data Link -) and +Battery
P1-50 (CAN Data Link +) to P1-34 (CAN Data Link -)
P1-50 (CAN Data Link +) to P1-42 (CAN Data Link Shield)
P1-34 (CAN Data Link -) to P1-42 (CAN Data Link Shield)
P1-50 (CAN Data Link +) and the −Battery terminalExpected Result:The resistance measures more than 20,000 Ohms.Results:
OK - The resistance is more than 20,000 Ohms. Proceed to Test Step 4.
Not OK - The resistance is less than 20,000 Ohms.Repair: There is a short in the harness wiring. Repair the connectors or wiring and/or replace the connectors or wiring.Verify that the repair eliminates the problem.STOPTest Step
Caterpillar parts catalog:
Parts bearing Caterpillar catalog:
9T4007
BEARING
303, 303.5C, 303.5D, 303.5E, 303C CR, 303E CR, 304C CR, 304D CR, 304E, 305.5D, 305.5E, 305C CR, 305D CR, 305E, 414E, 416B, 416C, 416D, 416E, 416F, 420D, 420E, 420F, 422E, 422F, 424D, 426, 426C, 428, 4...
303, 303.5C, 303.5D, 303.5E, 303C CR, 303E CR, 304C CR, 304D CR, 304E, 305.5D, 305.5E, 305C CR, 305D CR, 305E, 414E, 416B, 416C, 416D, 416E, 416F, 420D, 420E, 420F, 422E, 422F, 424D, 426, 426C, 428, 4...
6B5328
BEARING
303.5C, 303.5D, 303.5E, 303C CR, 304D CR, 304E, 769, D320A, G3304, G3306, G3306B
303.5C, 303.5D, 303.5E, 303C CR, 304D CR, 304E, 769, D320A, G3304, G3306, G3306B
1500909
BEARING
303, 303.5C, 303.5D, 303.5E, 303C CR, 303E CR, 304D CR, 304E
303, 303.5C, 303.5D, 303.5E, 303C CR, 303E CR, 304D CR, 304E
4423604
BEARING
901C, 902C, 903C
901C, 902C, 903C
2579648
BEARING-BUSHING
901C, 902C, 903C
901C, 902C, 903C
2579572
BEARING
901C, 902C, 903C
901C, 902C, 903C
2579575
BEARING AS
901C, 902C, 903C
901C, 902C, 903C
3974454
BEARING
901C, 902C, 903C
901C, 902C, 903C
3974455
BEARING
901C, 902C, 903C
901C, 902C, 903C
3987968
BEARING
901C, 902C, 903C
901C, 902C, 903C
3989853
BEARING
901C, 902C, 903C
901C, 902C, 903C
2409806
BEARING
901C, 902C, 903C
901C, 902C, 903C
3830431
BEARING
303.5E, 304E, 305.5E, 305E, 901C, 902C, 903C
303.5E, 304E, 305.5E, 305E, 901C, 902C, 903C
3830430
BEARING
303.5E, 304E, 305.5E, 305E, 901C, 902C, 903C
303.5E, 304E, 305.5E, 305E, 901C, 902C, 903C
3830468
BEARING
303.5E, 304E, 305.5E, 305E, 901C, 902C, 903C
303.5E, 304E, 305.5E, 305E, 901C, 902C, 903C
3830393
BEARING-CRANKSHAFT
303.5E, 304E, 305.5E, 305E, 901C, 902C, 903C
303.5E, 304E, 305.5E, 305E, 901C, 902C, 903C
3890729
BEARING-THRUST
303.5E, 304E, 305.5E, 305E, 901C, 902C, 903C
303.5E, 304E, 305.5E, 305E, 901C, 902C, 903C
3890728
BEARING-THRUST
303.5E, 304E, 305.5E, 305E, 901C, 902C, 903C
303.5E, 304E, 305.5E, 305E, 901C, 902C, 903C
3989801
BEARING
305.5E, 306, 306E
305.5E, 306, 306E
3836957
BEARING-CARRIER ROLLER
308E, 308E CR, 308E SR, 308E2 CR
308E, 308E CR, 308E SR, 308E2 CR
2592002
BEARING
305E
305E
3891597
BEARING-CRANKSHAFT
303.5E, 304E, 305.5E, 305E, 901C, 902C, 903C
303.5E, 304E, 305.5E, 305E, 901C, 902C, 903C
3891596
BEARING-CRANKSHAFT
303.5E, 304E, 305.5E, 305E, 901C, 902C, 903C
303.5E, 304E, 305.5E, 305E, 901C, 902C, 903C
3830375
BEARING-CRANKSHAFT
303.5E, 304E, 305.5E, 305E, 901C, 902C, 903C
303.5E, 304E, 305.5E, 305E, 901C, 902C, 903C