3J5752 BEARING Caterpillar parts
4S, 6A, 7A, 8A, D7F
Rating:
Alternative (cross code) number:
CA3J5752
3J-5752
3J5752
CA3J5752
3J-5752
3J5752
Weight: 2 pounds 1 kg.
BULLDOZER, TRACK-TYPE TRACTOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
CTP 3J5752 Sleeve Bearing for Heavy Equipment
CTP Sleeve Bearing Only || Sold in each || Easy in-and-out fit
CTP Sleeve Bearing Only || Sold in each || Easy in-and-out fit
CTP 3J5752 Sleeve Bearing for Heavy Equipment
CTP Sleeve Bearing Only || Sold in each || Easy in-and-out fit
CTP Sleeve Bearing Only || Sold in each || Easy in-and-out fit
Number on catalog scheme:
14
For full view, you need register
Information:
Use this procedure to troubleshoot an engine that has intermittent low power or power cutout.Note: Use this procedure only if the engine does not shutdown completely.Probable Causes
Connectors and wiring
Throttle signal
Fuel injectors
Fuel system
Inlet air restriction
Exhaust systemRecommended Actions
Note: If the problem only occurs under certain conditions, test the engine under those conditions. Examples of certain conditions are high engine speed, full load, and engine operating temperature. Troubleshooting the symptoms under other conditions can give misleading results.
Table 1
Troubleshooting Test Steps Values Results
1. Inspect the Electrical Connectors and the Wiring
A. Turn the main disconnect switch to the OFF position.
B. Check for the correct installation of the ECM J1/P1 and the J2/P2 connectors. Refer to Troubleshooting, "Electrical Power Supply - Test" for additional information.
C. Check for correct installation of the following connectors:
- Connectors for the wiring harness under the valve cover
- Connectors for the engine speed/timing sensors
D. Check the power and ground connections to the ECM. Refer to Troubleshooting, "Electrical Power Supply - Test" for additional information.
Connectors and Wiring
Result: The connectors and wiring appear to be
Connectors and wiring
Throttle signal
Fuel injectors
Fuel system
Inlet air restriction
Exhaust systemRecommended Actions
Note: If the problem only occurs under certain conditions, test the engine under those conditions. Examples of certain conditions are high engine speed, full load, and engine operating temperature. Troubleshooting the symptoms under other conditions can give misleading results.
Table 1
Troubleshooting Test Steps Values Results
1. Inspect the Electrical Connectors and the Wiring
A. Turn the main disconnect switch to the OFF position.
B. Check for the correct installation of the ECM J1/P1 and the J2/P2 connectors. Refer to Troubleshooting, "Electrical Power Supply - Test" for additional information.
C. Check for correct installation of the following connectors:
- Connectors for the wiring harness under the valve cover
- Connectors for the engine speed/timing sensors
D. Check the power and ground connections to the ECM. Refer to Troubleshooting, "Electrical Power Supply - Test" for additional information.
Connectors and Wiring
Result: The connectors and wiring appear to be
Caterpillar parts catalog:
Parts bearing Caterpillar catalog:
8A, 8U
571G, 572G, 977K, 977L, D7F, D7G, D7G2
571G, 572G, 977K, 977L, D7F, D7G, D7G2
953, D7F, D7G, D7G2, D7H, D8L
571G, 572G, D7F, D7G, D7G2
7A, 824G, 824G II, 824H, 824K, 824S, 825G, 825G II, 825H, 825K, 834B, 834G, 834H, 834K, 836, 8A, D7E, D7E LGP, D7G, D7G2, D7H, D7R, D7R II, D7R XR, D8N, D8R, D8R II, D8T, D9L
14E, 4S, 641, 651, 6A
7A, 814B, 814F, 814F II, 814S, 816F, 816F II, D7F, D7G, D7G2, D7H, D7R, D8N
824S, D7F, D7G, D7G2, D7H
7A, 7S, 814, 814B, 814F, 814F II, 816B, 816F, 816F II, D7F, D7G, D7G2, D7H
7A, 7S, 814B, 814F, 814F II, 814S, 816F, 816F II, D7F, D7G, D7G2
7A, D7G, D7G2
824G, 824G II, 824H, 824K, 825K, 826G, 826G II, 826H, 826K, 844, 844H, 844K, 8A, 8S, D7E, D7E LGP, D8L, D9N, D9R, D9T
5S, 619, 630A, 6A, 7A, 7G, 7S, 8 SR, 8A, 8S, 8U, 9A
824S, 8A, 8S, D8H, D8N, D8R, D8R II, D8T, D9E, D9G
3J6851
BEARING
8A, 8S
8A, 8S
3J0970
BEARING ASSEM.
8A, 8S, 8U, 9A
8A, 8S, 8U, 9A
3J6525
BEARING
8U, 9A, D9G
8U, 9A, D9G
824G, 824G II, 824H, 826G, 826G II, 826H, 844, 844H, 844K, 8A, 8S, 8U, D7E, D7E LGP, D8K, D8L, D9N, D9R, D9T
24H, 24M, 824G, 824G II, 824H, 826G, 826G II, 826H, 844, 844H, 844K, 8A, 8S, 8U, D8K, D8L, D9N, D9R, D9T
8A, 8U
3J6773
BEARING ASSEM.
8A, 9A, D9G
8A, 9A, D9G
4S, 6A, 7A, 8A, D7F