5K4787 BEARING Caterpillar parts
980, 980B
Rating:
Alternative (cross code) number:
CA5K4787
5K-4787
5K4787
CA5K4787
5K-4787
5K4787
Weight: 3 pounds 1 kg.
Information:
ID
89.06
mm
OD
108.014
mm
WIDTH
63.5
mm
WHEEL LOADER,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
CTP 5K4787 Sleeve Bearing for Heavy Equipment
CTP Sleeve Bearing Only || Sold in each || Easy in-and-out fit
CTP Sleeve Bearing Only || Sold in each || Easy in-and-out fit
CTP 5K4787 Sleeve Bearing for Heavy Equipment
CTP Sleeve Bearing Only || Sold in each || Easy in-and-out fit
CTP Sleeve Bearing Only || Sold in each || Easy in-and-out fit
Number on catalog scheme:
None
For full view, you need register
Information:
Illustration 1 g00596452
Schematic For Electrical SystemThe EMCP II monitors battery voltage in order to protect the EMCP II in case of a problem with the battery or battery charging. The EMCP II operates on a 24 DCV battery system or a 32 DCV battery system. The GSC receives battery voltage from RM-1 of the relay module terminal strip. The GSC measures this voltage. Voltage is received whenever the ECS is in the "START", "AUTO", or "STOP" position.Note: The GSC does not receive battery power when the ECS is in the OFF/RESET position. The GSC receives power when the contacts "6" and "9" of the ECS are jumpered. The GSC treats a CID 168 as an alarm fault.ProcedureThis diagnostic code can be caused by the following conditions:
The battery voltage is greater than 32 DCV for a 24 DCV battery system.
The battery voltage is greater than 45 DCV for a 32 DCV battery system.The setpoint for system voltage (P07) specifies the battery voltage as "0" for 24 volts and "1" for 32 volts. Clear the diagnostic code from the fault log after troubleshooting is complete.This procedure is used for troubleshooting an active fault or an inactive fault. Active alarm faults are shown on the upper display when the alarm codes key is pressed and the ECS is in any position except the OFF/RESET position. Inactive alarm faults are viewed in the fault log while the operator is in service mode. See Systems Operation, "Fault Log Viewing OP1".
Verify the fault.
View the upper display and check for active diagnostic faults for the battery voltage (CID 168 FMI 04).
Enter service mode and check the fault log for inactive diagnostic codes for the battery voltage (CID 168 FMI 04).Expected Result: A CID 168 FMI 04 diagnostic code is active.Results:
YES - A CID 168 FMI 04 diagnostic code is active. Proceed to Step 2.
NO - There are no diagnostic codes for the battery voltage. STOP.
Check the system's voltage.
Turn the ECS to the STOP position.
Measure the voltage across the battery terminals.Expected Result: For a 24 volt system, the voltage should be between 24.8 DCV and 29.5 DCV. For 32 volt system, the voltage should be between 33.1 DCV and 39.3 DCV.Results:
OK - For a 24 volt system, the voltage should be from 24.8 DCV to 29.5 DCV. For a 32 volt system, the voltage should be from 33.1 DCV to 39.3 DCV. Proceed to Step 3.
NOT OK - For 24 volt systems, the voltage is not between 24.8 DCV to 29.5 DCV. For a 32 volt system, the voltage is not between 33.1 DCV to 39.3 DCV. The fault is in the charging system. Proceed to Testing and Adjusting, "Charging System - Test". STOP.
Compare the voltage between TS1-1 and the battery voltage.
Turn the ECS to the STOP position.
Measure the battery voltage across the terminals. Take note of the battery voltage.
Measure the voltage between TS1-1 and TS1-30. Take note of the voltage.
Compare the voltage from Step 3.b with the voltage that was noted in Step 3.c.Expected Result: The
Caterpillar parts catalog:
Parts bearing Caterpillar catalog:
16, 1673C, 3126B, 3126E, 3176, 3176B, 3176C, 3196, 3304, 3306, 3306B, 3306C, 631C, 657, 657B, 769, 815, 824B, 834, 963, 966C, 973, 980B, 983, 988, C-10, C-12, C-9, C11, C13, C7, C9, CX31-C13I, CX31-C9...
16, 1673C, 3126B, 3126E, 3176, 3176B, 3176C, 3196, 3304, 3306, 3306B, 3306C, 350, 641B, 650B, 772, 777, 815, 963, 966C, 973, 980B, 992, C-10, C-12, C-9, C11, C13, C7, C9, CX31-C13I, CX31-C9I, D10, D34...
120G, 12G, 130G, 140G, 1673C, 215, 225, 3208, 3304, 3306, 518, 613B, 613C, 637D, 920, 941, 950, 955L, 980B, CB-614, CS-551, D4D, D5, D5B, D6D, PR-1000, PS-500
120B, 120G, 12E, 12G, 130G, 140B, 140G, 14G, 160G, 16G, 3304, 3306, 561B, 561C, 621, 627, 637, 657B, 666B, 769, 824B, 834, 931B, 931C, 931C II, 933, 933C, 935B, 939, 939C, 951B, 955K, 977H, 977K, 980,...
225, 235, 245, 350 L, 375, 5080, 583R, 589, 980B, 988, 992, D343, D348, D379, D379B, D398, D399
578, 583R, 587R, 589, 814, 920, 930, 931B, 950, 966C, 977H, 980, 980B, D3B, D4D
120G, 12G, 130G, 140G, 160G, 613, 613B, 769C, 769D, 771C, 771D, 772, 773, 773B, 773D, 775B, 775D, 776C, 776D, 777, 777B, 777D, 784B, 784C, 785, 785B, 785C, 785D, 789B, 789C, 789D, 793B, 793C, 920, 930...
621, 621B, 621E, 621F, 621G, 621R, 623B, 623E, 623F, 623G, 627, 627B, 627E, 627F, 627G, 630A, 630B, 631C, 631D, 631E, 631G, 633, 633C, 633D, 633E, 633E II, 637, 637B, 637D, 637E, 637G, 980, 980B
16G, 16H, 16H NA, 16M, 980, 980B
16G, 16H, 16H NA, 16M, 980, 980B
320B FM LL, 322B L, 322C FM, 324D FM LL, 325B L, 325D FM, 325D FM LL, 330B L, 330D FM, 568 FM LL, 980B, 988, GH52, GLC85, GLL60, GLS63
980, 980B, 988
980, 980B
16G, 16H, 16H NA, 16M, 980, 980B
16G, 16H, 16H NA, 16M, 980, 980B
5K6446
BEARING
824B, 988
824B, 988
7S6623
BEARING
824B, 825B, 826B, 834, 988
824B, 825B, 826B, 834, 988
9M2147
BEARING
16, 769, 824, 824B, 834, 988
16, 769, 824, 824B, 834, 988
5K9105
BEARING
980, 980B
980, 980B
6K8335
BEARING ASSEM.
824S, 988
824S, 988
9M9419
BEARING
824, 824B, 834, 988
824, 824B, 834, 988
988
374D L, 988, PIN GRAB
980, 980B, GLC85