6I5169 BEARING-SLEEVE Caterpillar parts
350 L, 375, 375 L, 5080
Rating:
Alternative (cross code) number:
CA6I5169
6I-5169
6I5169
CA6I5169
6I-5169
6I5169
Weight: 12 pounds 5 kg.
Information:
ID
140.34
mm
OD
164.29
mm
WIDTH
134
mm
EXCAVATOR, FRONT SHOVEL,
Number on catalog scheme:
1C
For full view, you need register
Information:
Illustration 1 g01457631
Pump compartment (1) Pressure tap (delivery pressure)
Attach a 60000 kPa (8700 psi) pressure gauge to pressure tap (1) .
Illustration 2 g01457713
(2) FT-2788 Blocker pin (3) Sprocket
Place blocker pin (2) in sprocket (3) in order to block forward left travel.
Start the engine.
Place the machine controls at the following settings: engine speed dial "10" and AEC switch OFF. Refer to Testing and Adjusting, "Engine Performance - Test (Engine Speed)" for engine rpm settings.
Place the hydraulic activation control lever in the UNLOCKED position.
Increase the hydraulic oil temperature to 55° 5°C (131° 9°F).
Illustration 3 g01620555
Main control valve (4) Low pressure adjustment screw (5) Low pressure locknut (6) High pressure adjustment screw (7) High pressure locknut (8) Main relief valve
Loosen locknut (5) and turn adjustment screw (4) until the adjustment plug contacts the bottom. Do not overtighten adjustment screw (4) . Tighten locknut (5) .
Slowly move the left travel control lever to full FORWARD position and check the pressure gauge reading at pressure tap (1). The pressure setting should be 32000 - 34000 kPa (4640 - 4930 psi).
Return the left travel control lever to the NEUTRAL position.
In order to adjust the travel operation of the main relief valve, loosen locknut (7) and turn adjustment screw (6) until the pressure gauge reading at pressure tap (1) is 32000 - 34000 kPa (4640 - 4930 psi).Note: Turning adjustment screw (6) clockwise increases the pressure. Turning adjustment plug (6) counterclockwise decreases the pressure.Note: Always make final pressure adjustments on pressure rise.
Tighten locknut (7) to a torque of 83 5 N m (60 4 lb ft).Implement Operation
Position the machine on level ground.
Stop the engine.
Release the pressure in the hydraulic system. Refer to Testing and Adjusting, "Hydraulic System Pressure - Release".
Illustration 4 g01457631
Pump compartment (1) Pressure tap (delivery pressure)
Attach a 60000 kPa (8700 psi) pressure gauge to pressure tap (2) .
Start the engine.
Place the machine controls at the following settings: engine speed dial "10" and AEC switch OFF. Refer to Testing and Adjusting, "Engine Performance - Test (Engine Speed)" for engine rpm settings.
Place the hydraulic activation control lever in the UNLOCKED position.
Increase the hydraulic oil temperature to 55° 5°C (131° 9°F).
Illustration 5 g01620555
Main control valve (4) Low pressure adjustment screw (5) Low pressure locknut (6) High pressure adjustment screw (7) High pressure locknut (8) Main relief valveNote: With low pressure adjustment screw (4) on the bottom, the pressure of the main relief valve is set higher than the pressure of the line relief valves for the implements. Adjustment screw (4) must be set to a lower pressure for the specified pressure to be seen.
In order to adjust the implement operation of the main control valve, loosen locknut (5) and turn adjustment screw (4). Turn adjustment screw (4) counterclockwise for one-eighth turn.
Slowly move the joystick for
Caterpillar parts catalog:
Parts bearing Caterpillar catalog:
345C, 350 L, 365B, 365B II, 365B L, 365C, 365C L, 365C L MH, 374D L, 374F L, 375, 375 L, 385B, 385C, 385C L, 390D, 390D L, 390F L, 5080, P16, S25
365B, 365B II, 365B L, 365C, 365C L, 374D L, 374F L, 375, 375 L, 385B, 385C, 385C L, 390D, 390D L, 390F L, 5080
330B L, 330C FM, 330D FM, 345B, 345B II, 345B II MH, 345B L, 350 L, 365B, 365B II, 365C, 375, 385B, 385C L, 5080, S305, S365B, S365C, VHS-50, VHS-60/3, W345B II
365B, 365B II, 365B L, 365C, 365C L, 374D L, 374F L, 375, 375 L, 385B, 385C, 385C L, 390D, 390D L, 390F L, 5080, P115, VPC-30
365C, 375, 375 L, 385B, 385C, 385C L, 5080, P115, VPC-30
375, 375 L, 5080
350, 350 L, 365C, 375, 375 L, 385B, 385C, 385C L, 390D, 390D L, 390F L, 5080, S305, S465, VHS-50
365B, 365B II, 365B L, 365C, 365C L, 374D L, 374F L, 375, 375 L, 385B, 385C, 385C L, 5080
320B, 320C, 321C, 322B LN, 322C, 322C FM, 325, 325B, 325B L, 325C, 325D, 330B L, 330C L, 345B II, 345B L, 365B, 375, 5080, TK1051
325C, 330, 330B, 330B L, 345B II, 345B L, 350 L, 365B, 5080, S25, W330B
322 LN, 322B L, 322B LN, 322C, 322C FM, 324D FM, 324D FM LL, 325 LN, 325B L, 330, 330 FM L, 330 L, 330B, 330B L, 345B II, 345B L, 350, 350 L, 365B, 365B II, 365B L, M325B, W330B
322B, 322B L, 322B LN, 322C, 322C FM, 324D FM, 325, 325B, 325B L, 325C, 325C L, 330, 330 FM L, 330 L, 330B, 330B L, 330C L, 345B, 345B II, 345B II MH, 345B L, 350 L, 365B, 365B II, 375, 385B, M325B, S...
365B, 365B II, 365B L, 365C, 365C L, 374D L, 374F L, 375, 375 L, 385B, 385C, 385C L, 5080
365C, 375, 375 L, 385B, 385C, 385C L, 5080
350, 350 L, 365C, 375, 375 L, 385B, 385C, 385C L, 390D, 390D L, 390F L, 5080, S305, S465, VHS-50
375, 375 L, 5080
365C, 375, 375 L, 385B, 385C, 385C L, 5080, P115, VPC-30
365B, 375, 375 L, 5080
6DE4545
BEARING
AD40, AE40
AD40, AE40
6DE3511
BEARING
AD40, AE40
AD40, AE40
325C, 330, 330B, 330B L, 345B II, 345B L, 350 L, 365B, 5080, S25, W330B
320B, 320C, 321C, 322B LN, 322C, 322C FM, 325, 325B, 325B L, 325C, 325D, 330B L, 330C L, 345B II, 345B L, 365B, 375, 5080, TK1051
1035366
BEARING-SLEEVE
350, 350 L, 375, 5080
350, 350 L, 375, 5080
1289883
BEARING-SLEEVE
320B, 322B L, 322C, 322C FM, 324D FM, 324D FM LL, 325, 325B L, 325C FM, 325D FM, 325D FM LL, 5080, M325B, M325C MH, M325D L MH
320B, 322B L, 322C, 322C FM, 324D FM, 324D FM LL, 325, 325B L, 325C FM, 325D FM, 325D FM LL, 5080, M325B, M325C MH, M325D L MH