7K9576 BEARING Caterpillar parts
955K, 955L
Rating:
Alternative (cross code) number:
CA7K9576
7K-9576
7K9576
CA7K9576
7K-9576
7K9576
Weight: 2 pounds 1 kg.
Information:
ID
89.06
mm
OD
101.664
mm
WIDTH
75.41
mm
TRACK LOADER,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
CTP 7K9576 Sleeve Bearing for Heavy Equipment
CTP Sleeve Bearing Only || Sold in each || Easy in-and-out fit
CTP Sleeve Bearing Only || Sold in each || Easy in-and-out fit
CTP 7K9576 Sleeve Bearing for Heavy Equipment
CTP Sleeve Bearing Only || Sold in each || Easy in-and-out fit
CTP Sleeve Bearing Only || Sold in each || Easy in-and-out fit
Number on catalog scheme:
6
For full view, you need register
Information:
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A FT-2610 Driver Tube 1
B 4D-3120 Bolt 1
C FT-2612 Bearing Removal Tool 1
D 1P-1861 Retaining Ring Pliers 1 Start By:
Remove the unit injector hydraulic pump. Refer to Disassembly and Assembly, "Unit Injector Hydraulic Pump - Remove".
Remove the injection actuation pressure control valve. Refer to Disassembly and Assembly, "Injection Actuation Pressure Control Valve - Remove".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Do not allow dirt to enter the fuel system. Thoroughly clean the area around a fuel system component that will be disconnected. Fit a suitable cover over disconnected fuel system component.
Illustration 1 g01094410
Remove pressure compensator valve (1).
Remove manifold (2).
Remove bolts (4) from valve block (3).
Illustration 2 g01094416
Remove valve block (3), control piston (6), and gasket (5).
Illustration 3 g01094422
Remove rotating group (7). Minor twisting of the rotating group may be necessary in order to remove the rotating group.
Illustration 4 g01094430
Install Tooling (A) in the pump group. Use a suitable press in order to remove shaft (8) from the front bearing.
Illustration 5 g01094431
Remove bolts (9). Remove covers (10).
Illustration 6 g01094441
Remove O-ring seal (12) from pintle bearing (14) that is opposite of spring seat (11). Install Tooling (B) into the pintle bearing finger tight.
Remove plug (13), if necessary.
Tighten Tooling (B) into the pintle bearing until the pintle bearing is removed.
Illustration 7 g01094444
In order to remove the pintle bearing from the other side of the pump group, you need to hold yoke (15) firmly. Use Tooling (B) to remove the pintle bearing.
Remove yoke (15).
Illustration 8 g01094447
Personal injury can result from parts and/or covers under spring pressure.Spring force will be released when covers are removed.Be prepared to hold spring loaded covers as the bolts are loosened.
Remove spring seat (11) and the spring.
Illustration 9 g01094449
Use Tooling (D) to remove retaining ring (17). Remove bearing (16).
Illustration 10 g01094450
Use Tooling (D) to remove retaining ring (19). Remove shaft seal (18).
Illustration 11 g01094452
Use Tooling (C) and a suitable press in order to remove bearing (20).
Illustration 12 g01094458
Remove plugs (21) and plug (22) from valve block (3).
Table 1
Required Tools
Tool Part Number Part Description Qty
A FT-2610 Driver Tube 1
B 4D-3120 Bolt 1
C FT-2612 Bearing Removal Tool 1
D 1P-1861 Retaining Ring Pliers 1 Start By:
Remove the unit injector hydraulic pump. Refer to Disassembly and Assembly, "Unit Injector Hydraulic Pump - Remove".
Remove the injection actuation pressure control valve. Refer to Disassembly and Assembly, "Injection Actuation Pressure Control Valve - Remove".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Do not allow dirt to enter the fuel system. Thoroughly clean the area around a fuel system component that will be disconnected. Fit a suitable cover over disconnected fuel system component.
Illustration 1 g01094410
Remove pressure compensator valve (1).
Remove manifold (2).
Remove bolts (4) from valve block (3).
Illustration 2 g01094416
Remove valve block (3), control piston (6), and gasket (5).
Illustration 3 g01094422
Remove rotating group (7). Minor twisting of the rotating group may be necessary in order to remove the rotating group.
Illustration 4 g01094430
Install Tooling (A) in the pump group. Use a suitable press in order to remove shaft (8) from the front bearing.
Illustration 5 g01094431
Remove bolts (9). Remove covers (10).
Illustration 6 g01094441
Remove O-ring seal (12) from pintle bearing (14) that is opposite of spring seat (11). Install Tooling (B) into the pintle bearing finger tight.
Remove plug (13), if necessary.
Tighten Tooling (B) into the pintle bearing until the pintle bearing is removed.
Illustration 7 g01094444
In order to remove the pintle bearing from the other side of the pump group, you need to hold yoke (15) firmly. Use Tooling (B) to remove the pintle bearing.
Remove yoke (15).
Illustration 8 g01094447
Personal injury can result from parts and/or covers under spring pressure.Spring force will be released when covers are removed.Be prepared to hold spring loaded covers as the bolts are loosened.
Remove spring seat (11) and the spring.
Illustration 9 g01094449
Use Tooling (D) to remove retaining ring (17). Remove bearing (16).
Illustration 10 g01094450
Use Tooling (D) to remove retaining ring (19). Remove shaft seal (18).
Illustration 11 g01094452
Use Tooling (C) and a suitable press in order to remove bearing (20).
Illustration 12 g01094458
Remove plugs (21) and plug (22) from valve block (3).
Caterpillar parts catalog:
Parts bearing Caterpillar catalog:
120G, 12G, 130G, 140G, 14G, 160G, 16G, 515, 518, 518C, 525, 525B, 528, 528B, 530B, 535B, 545, 561D, 572G, 578, 583K, 583R, 587R, 589, 65, 814, 814S, 815, 816, 824B, 824S, 834B, 836, 910, 910E, 910G, 9...
120G, 130G, 225, 3304, 3304B, 920, 930, 936F, 941, 950, 950B, 951B, 955L, 963, D4D, D4E, D4E SR, D5H, D5H XL, G3304, G936
120G, 130G, 225, 3304, 3304B, 920, 930, 936F, 941, 950, 950B, 951B, 955L, 963, D4D, D4E, D4E SR, D5H, D5H XL, G3304, G936
120B, 120G, 12E, 130G, 140B, 1673B, 1673C, 225, 235, 3304, 3306, 561B, 637D, 930, 941, 950, 955H, 955L, 966C, D330A, D330B, D333A, D4D, D5, D6C, D6D, D7F
561D, 571G, 572G, 583H, 583K, 594, 594H, 641, 651, 657, 657B, 666, 824, 824B, 834, 955K, 955L, 977H, 977K, 977L, 983, 983B, 988, 992, D5, D5B, D6C, D6D, D6E, D6G, D6G2 LGP, D6G2 XL, D7F, D7G, D7G2, D8...
594H, 615, 615C, 627, 627B, 627E, 627F, 627G, 627H, 627K, 627K LRC, 631C, 631E, 631G, 633C, 633D, 633E II, 637B, 637D, 637E, 637G, 650B, 657B, 657E, 657G, 768C, 769C, 772B, 773B, 773D, 773E, 773F, 773...
120G, 12G, 130G, 140G, 160G, 518C, 528, 528B, 530B, 572G, 613C, 613C II, 613G, 621, 621B, 621E, 621F, 621G, 621H, 621K, 621R, 623, 623B, 623E, 623F, 623G, 623H, 623K, 623K LRC, 627B, 627E, 627F, 627G,...
955K, 955L, 966C, 966R
518C, 528, 528B, 530B, 637D, 637E, 637G, 730, 814, 815, 816, 950B, 950B/950E, 950F, 950F II, 955K, 955L, 960F
955K, 955L, 966C
941, 951B, 955K, 955L
16, 594, 594H, 651, 657, 657B, 768B, 769, 772, 773, 824B, 834, 950, 955K, 955L, 966C, 988, 992, D7F, D8H, D9G, D9H
955K, 955L
955K, 955L, 966C, 966R
916, 955K, 955L
5B2090
BEARING
D348
D348
D353C, G353D
6H2744
BEARING
12E, 12F, 641B, 651E, 657B, 657E, 657G, D320A
12E, 12F, 641B, 651E, 657B, 657E, 657G, D320A
1L5357
BEARING
D343
D343
4L3793
BEARING
D343
D343
1L6954
BEARING
D343
D343
D379B, G398, G399
0347897
BEARING
D398, D5B, D5E
D398, D5B, D5E
955K, 955L