7P8753 BEARING Caterpillar parts
924G, 924GZ, 924H, 924HZ, 928HZ, 930G, 930K, 938F, 973, 973C, 973D, IT38G II, IT38H
Rating:
Alternative (cross code) number:
CA7P8753
7P-8753
7P8753
CA7P8753
7P-8753
7P8753
Weight: 2 pounds 0 kg.
Information:
ID
76.481
mm
OD
88.978
mm
WIDTH
78
mm
INTEGRATED TOOLCARRIER, WHEEL LOADER,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
YNRSP 7P8753 Sleeve Bearing Fits Model IT38G II/IT38H/3056/3056E/3116/3126B/3306/C-9/C6.6/C9
YNRSP Brand: YNRSP || Part Number: 7P8753 || Part Type: Sleeve Bearing || Weight: 2.09 lbs (0.95 kg) || Fits Model: 3056, 3056E, 3116, 3126B, 3306, C-9, C6.6, C9, IT38G II, IT38H
YNRSP Brand: YNRSP || Part Number: 7P8753 || Part Type: Sleeve Bearing || Weight: 2.09 lbs (0.95 kg) || Fits Model: 3056, 3056E, 3116, 3126B, 3306, C-9, C6.6, C9, IT38G II, IT38H
CTP 7P8753 Sleeve Bearing for Heavy Equipment
CTP Sleeve Bearing Only || Sold in each || Easy in-and-out fit
CTP Sleeve Bearing Only || Sold in each || Easy in-and-out fit
Number on catalog scheme:
For full view, you need register
Compatible equipment models: 7P8753:
Information:
Conditions Which Generate This Code:
Illustration 1 g01362225
Connections of the transmission output speed sensor 1This diagnostic code is associated with the transmission output speed sensor 1. The FMI 12 means that the ECM has determined that the signal frequency or the signal pulse width is not within the expected range.System Response:A diagnostic code will be displayed on the Caterpillar Electronic Technician (Cat ET). The tractor will operate normally unless more than one speed sensor has failed.Test Step 1. CHECK THE RESISTANCE OF THE CASE OF THE SENSOR .
Turn the key start switch and the disconnect switch (if equipped) to the OFF position.
Disconnect the machine harness connector from the sensor.
Measure the resistance from contact 1 and from contact 2 to the case of the sensor.Expected Result:The resistance is greater than 5000 ohms. Results:
OK - The resistance is greater than 5000 ohms. Proceed to Test Step 2.
NOT OK - The resistance is NOT greater than 5000 ohms. The speed sensor has failed.Repair: Replace the sensor.STOPTest Step 2. CHECK THE RESISTANCE OF THE SENSOR.
The key start switch and the disconnect switch (if equipped) remain in the OFF position.
Measure the resistance between contact 1 and contact 2 of the connector of the sensor.Expected Result:The resistance is between 600 and 1800 ohms.Results:
OK - The resistance is between 600 and 1800 ohms. The resistance is correct. Proceed to Test Step 3.
NOT OK - The resistance is NOT between 600 and 1800 ohms. The resistance is not correct. The sensor has failed.Repair: Replace the sensor.STOPTest Step 3. CHECK FOR AN OPEN HARNESS.
The key start switch and the disconnect switch (if equipped) remain in the OFF position.
Reconnect the machine harness connector to the sensor.
Disconnect the machine harness connectors J1 and J2 from the machine ECM.
At the machine harness connector J1, measure the resistance from contact J1-41 to J1-40.Expected Result:The resistance is between 600 and 1800 ohms.Results:
OK - The resistance is between 600 and 1800 ohms. The circuit is correct. Proceed to Test Step 4.
NOT OK - The resistance is NOT between 600 and 1800 ohms. The circuit is open in the machine harness. Repair: Repair the machine harness or replace the machine harness.STOPTest Step 4. CHECK FOR A SHORT IN THE RETURN CIRCUIT OF THE MACHINE HARNESS.
The key start switch and the disconnect switch (if equipped) remain in the OFF position.
Disconnect the machine harness from the sensor.
At the machine harness connector J1, measure the resistance between contacts J1-40 and J1-41 to all sources of ground.Expected Result:Each resistance measurement is greater than 5000 ohms.Results:
OK - Each resistance measurement is greater than 5000 ohms. Proceed to Test Step5.
NOT OK - There is a short in the machine harness.Repair: Repair the machine harness or replace the machine harness.STOPTest Step 5. INSPECT THE SENSOR AND ADJUST THE SENSOR.
The key start switch and the disconnect switch (if equipped) remain in the OFF position. The sensor remains disconnected from the machine harness.
Remove the speed sensor. Inspect the sensor for damage or the presence
Illustration 1 g01362225
Connections of the transmission output speed sensor 1This diagnostic code is associated with the transmission output speed sensor 1. The FMI 12 means that the ECM has determined that the signal frequency or the signal pulse width is not within the expected range.System Response:A diagnostic code will be displayed on the Caterpillar Electronic Technician (Cat ET). The tractor will operate normally unless more than one speed sensor has failed.Test Step 1. CHECK THE RESISTANCE OF THE CASE OF THE SENSOR .
Turn the key start switch and the disconnect switch (if equipped) to the OFF position.
Disconnect the machine harness connector from the sensor.
Measure the resistance from contact 1 and from contact 2 to the case of the sensor.Expected Result:The resistance is greater than 5000 ohms. Results:
OK - The resistance is greater than 5000 ohms. Proceed to Test Step 2.
NOT OK - The resistance is NOT greater than 5000 ohms. The speed sensor has failed.Repair: Replace the sensor.STOPTest Step 2. CHECK THE RESISTANCE OF THE SENSOR.
The key start switch and the disconnect switch (if equipped) remain in the OFF position.
Measure the resistance between contact 1 and contact 2 of the connector of the sensor.Expected Result:The resistance is between 600 and 1800 ohms.Results:
OK - The resistance is between 600 and 1800 ohms. The resistance is correct. Proceed to Test Step 3.
NOT OK - The resistance is NOT between 600 and 1800 ohms. The resistance is not correct. The sensor has failed.Repair: Replace the sensor.STOPTest Step 3. CHECK FOR AN OPEN HARNESS.
The key start switch and the disconnect switch (if equipped) remain in the OFF position.
Reconnect the machine harness connector to the sensor.
Disconnect the machine harness connectors J1 and J2 from the machine ECM.
At the machine harness connector J1, measure the resistance from contact J1-41 to J1-40.Expected Result:The resistance is between 600 and 1800 ohms.Results:
OK - The resistance is between 600 and 1800 ohms. The circuit is correct. Proceed to Test Step 4.
NOT OK - The resistance is NOT between 600 and 1800 ohms. The circuit is open in the machine harness. Repair: Repair the machine harness or replace the machine harness.STOPTest Step 4. CHECK FOR A SHORT IN THE RETURN CIRCUIT OF THE MACHINE HARNESS.
The key start switch and the disconnect switch (if equipped) remain in the OFF position.
Disconnect the machine harness from the sensor.
At the machine harness connector J1, measure the resistance between contacts J1-40 and J1-41 to all sources of ground.Expected Result:Each resistance measurement is greater than 5000 ohms.Results:
OK - Each resistance measurement is greater than 5000 ohms. Proceed to Test Step5.
NOT OK - There is a short in the machine harness.Repair: Repair the machine harness or replace the machine harness.STOPTest Step 5. INSPECT THE SENSOR AND ADJUST THE SENSOR.
The key start switch and the disconnect switch (if equipped) remain in the OFF position. The sensor remains disconnected from the machine harness.
Remove the speed sensor. Inspect the sensor for damage or the presence
Cat SIS web machinery list:
Parts bearing Caterpillar catalog:
515, 525, 525B, 525C, 525D, 535B, 535C, 535D, 545, 545C, 545D, 555D, 928F, 938F, 938G, 938G II, 938H, 950 GC, IT28F, IT38F, IT38G, IT38G II, IT38H
515, 525, 525B, 525C, 525D, 535B, 535C, 535D, 545, 545C, 545D, 555D, 910E, 918F, 924F, 924G, 924GZ, 924H, 924HZ, 928F, 928G, 928H, 928HZ, 930G, 938F, 938G, 938G II, 938H, 950 GC, IT12B, IT14B, IT14F, ...
515, 525, 525B, 525C, 525D, 535B, 535C, 535D, 545, 545C, 545D, 555D, 928F, 938F, 938G, 938G II, 938H, 950 GC, IT28F, IT38F, IT38G, IT38G II, IT38H
515, 518C, 525, 525B, 525C, 528, 528B, 530B, 535B, 535C, 545, 545C, 814F, 815B, 815F, 816F, 924F, 924G, 924GZ, 924H, 924HZ, 926, 928F, 928G, 928H, 928HZ, 930G, 930R, 936, 936F, 938F, 938G, 938G II, 95...
24H, 24M, 611, 615, 615C, 918F, 924F, 924G, 924GZ, 924H, 924HZ, 926, 928F
928G, 928H, 928HZ, IT18F, IT28F, IT28G
533, 543, 924F, 924G, 924GZ, 924H, 924HZ, 924K, 928F, 928G, 928H, 928HZ, 930G, 930K, 938F, 938G, 938G II, 938H, 938K, HA770, HA771, HA870, HA871, IT18F, IT24F, IT28F, IT28G, IT38F, IT38G, IT38G II, IT...
910E, 918F, 924F, 924G, 924GZ, 924H, 924HZ, 928G, 928H, 928HZ, 930G, IT12B, IT14B, IT14F, IT18F, IT24F, IT28G
918F, 924F, 924G, 924GZ, 924H, 924HZ, 924K, IT18F, IT24F
924G, 924GZ, 924H, 924HZ, 928G, 928HZ, IT28G
928HZ, 930G, 950 GC, 950B, 950B/950E, 950F, 950F II, 950G, 950G II, 950H, 960F, 962G, 962G II, 962H, IT62G, IT62G II, IT62H
924G, 924GZ, 924H, 924HZ
924K, 930K, 950K, 962K, 973, 973C, 973D, 986H
963, 963B, 963C, 963D, 973, 973C, 973D
320D, 324D L, 325B L, 325C, 325D L, 329D L, 973, 973C, 973D, D7E, D7E LGP
973, 973C, 973D
973, 973C, 973D, 977K, 977L
1P8786
BEARING AS
973C, 973D, D7R, D7R II
973C, 973D, D7R, D7R II
525B, 535B, 545, 572R, 572R II, 623H, 631B, 631D, 631E, 631G, 637D, 637E, 637G, 953, 953C, 953D, D7H, D7R, D7R II, D7R XR
14G, 14H, 14H NA, 14M, 16G, 16H, 16H NA, 16M, 943, 953, 953C, 953D, D6R, D6R STD, D6T, D6T LGP, D6T LGPPAT
AP-1000B, AP-1055B, AP-1055D, AP-600D, AP-650B, AP-655C, AP-655D, AP1000E, AP1055E, AP555E, BG-225C, BG-2455C, BG-2455D, BG-245C, BG-260D, BG1000E, BG1055E, BG500E, BG600D, BG655D, D6H, D6H II, D6H XL...
583T, D6R, D6R II, D6R III, D6R STD, D6T, D6T LGP, D6T LGPPAT, D6T XL, PL83
2582306
BEARING-SLEEVE
D6R, D6R II
D6R, D6R II
578, 583R, 587R, 589, 814B, 814F, 815B, 815F, 816B, 816F, 824C, 824G, 824G II, 824H, 825C, 825G, 825G II, 825H, 826C, 826G, 826G II, 826H, 834B, 836, 836G, 836H, 918F, 924F, 926, 938F, 950F, 950F II, ...