9J6687 BEARING-SLEEVE Caterpillar parts
854G, D9L
Rating:
Alternative (cross code) number:
CA9J6687
9J-6687
9J6687
CA9J6687
9J-6687
9J6687
Weight: 10 pounds 4 kg.
Information:
ID
102.29
mm
OD
127.114
mm
WIDTH
135
mm
TRACK-TYPE TRACTOR, WHEEL DOZER,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
CTP 9J6687 Sleeve Bearing for Heavy Equipment
CTP Sleeve Bearing Only || Sold in each || Easy in-and-out fit
CTP Sleeve Bearing Only || Sold in each || Easy in-and-out fit
CTP 9J6687 Sleeve Bearing for Heavy Equipment
CTP Sleeve Bearing Only || Sold in each || Easy in-and-out fit
CTP Sleeve Bearing Only || Sold in each || Easy in-and-out fit
Number on catalog scheme:
3C
For full view, you need register
Information:
Removal Procedure
Ensure that all adjustments and repairs that are carried out to the fuel system are performed by authorized personnel that have the correct training.Before beginning ANY work on the fuel system, refer to Operation and Maintenance Manual, "General Hazard Information and High Pressure Fuel Lines" for safety information. Refer to System Operation, Testing and Adjusting, "Cleanliness of Fuel System Components" for detailed information on the standards of cleanliness that must be observed during ALL work on the fuel system.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Turn the fuel supply to the OFF position.
Illustration 1 g01334883
Typical example
Make temporary identification marks on plastic tube assemblies (2), (4) and (5) in order to show the correct position of the tube assemblies.
Place a suitable container below the fuel filter base in order to catch any fuel that might be spilled.
Disconnect plastic tube assemblies (2), (4) and (5) from fuel filter base (1). Plug the plastic tube assemblies with new plugs. Cap the ports in the fuel filter base with new caps.
Remove fuel filter (6). Refer to Operation and Maintenance Manual, "Fuel System Secondary Filter - Replace".
Remove bolts (3) from fuel filter base (1). Remove the fuel filter base from the mounting bracket. Note: Do not disassemble the fuel filter base.Installation Procedure
Ensure that all adjustments and repairs that are carried out to the fuel system are performed by authorized personnel that have the correct training.Before beginning ANY work on the fuel system, refer to Operation and Maintenance Manual, "General Hazard Information and High Pressure Fuel Lines" for safety information. Refer to System Operation, Testing and Adjusting , "Cleanliness of Fuel System Components" for detailed information on the standards of cleanliness that must be observed during ALL work on the fuel system.
Ensure that fuel filter base (1) is clean and free from damage. If necessary, replace the complete fuel filter base and filter assembly.
Illustration 2 g01334883
Typical example
Position fuel filter base (1) on the mounting bracket. Install bolts (3). Tighten the bolts to a torque of 44 N m (32 lb ft).
Remove the plugs from the plastic tube assemblies. Remove the caps from the ports in the fuel filter base.
Ensure that the plastic tube assemblies are installed in the original positions. Failure to connect the plastic tube assemblies to the correct ports will allow contamination to enter the fuel system. Contaminated fuel will cause serious damage to the engine.
Connect plastic tube assemblies (2), (4) and (5) to fuel filter base (1).
If necessary, install a new fuel filter (6) to fuel filter base (1). Refer to Operation and Maintenance Manual, "Fuel System Secondary Filter - Replace" for the correct procedure.
Turn the fuel supply to the ON position. End By:
Remove the air from the fuel system. Refer to Operation and Maintenance Manual, "Fuel System - Prime".
Ensure that all adjustments and repairs that are carried out to the fuel system are performed by authorized personnel that have the correct training.Before beginning ANY work on the fuel system, refer to Operation and Maintenance Manual, "General Hazard Information and High Pressure Fuel Lines" for safety information. Refer to System Operation, Testing and Adjusting, "Cleanliness of Fuel System Components" for detailed information on the standards of cleanliness that must be observed during ALL work on the fuel system.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Turn the fuel supply to the OFF position.
Illustration 1 g01334883
Typical example
Make temporary identification marks on plastic tube assemblies (2), (4) and (5) in order to show the correct position of the tube assemblies.
Place a suitable container below the fuel filter base in order to catch any fuel that might be spilled.
Disconnect plastic tube assemblies (2), (4) and (5) from fuel filter base (1). Plug the plastic tube assemblies with new plugs. Cap the ports in the fuel filter base with new caps.
Remove fuel filter (6). Refer to Operation and Maintenance Manual, "Fuel System Secondary Filter - Replace".
Remove bolts (3) from fuel filter base (1). Remove the fuel filter base from the mounting bracket. Note: Do not disassemble the fuel filter base.Installation Procedure
Ensure that all adjustments and repairs that are carried out to the fuel system are performed by authorized personnel that have the correct training.Before beginning ANY work on the fuel system, refer to Operation and Maintenance Manual, "General Hazard Information and High Pressure Fuel Lines" for safety information. Refer to System Operation, Testing and Adjusting , "Cleanliness of Fuel System Components" for detailed information on the standards of cleanliness that must be observed during ALL work on the fuel system.
Ensure that fuel filter base (1) is clean and free from damage. If necessary, replace the complete fuel filter base and filter assembly.
Illustration 2 g01334883
Typical example
Position fuel filter base (1) on the mounting bracket. Install bolts (3). Tighten the bolts to a torque of 44 N m (32 lb ft).
Remove the plugs from the plastic tube assemblies. Remove the caps from the ports in the fuel filter base.
Ensure that the plastic tube assemblies are installed in the original positions. Failure to connect the plastic tube assemblies to the correct ports will allow contamination to enter the fuel system. Contaminated fuel will cause serious damage to the engine.
Connect plastic tube assemblies (2), (4) and (5) to fuel filter base (1).
If necessary, install a new fuel filter (6) to fuel filter base (1). Refer to Operation and Maintenance Manual, "Fuel System Secondary Filter - Replace" for the correct procedure.
Turn the fuel supply to the ON position. End By:
Remove the air from the fuel system. Refer to Operation and Maintenance Manual, "Fuel System - Prime".
Caterpillar parts catalog:
Parts bearing Caterpillar catalog:
844, 844H, 844K, 854G, 854K, 990, 990 II, 990H, 990K, 992G, 992K
24H, 834B, 836, 844, 988B, 988F, 988F II, 990, 990 II, D10N, D10R, D8L, D9L, D9R
844, 844H, 844K, 854G, 854K, 990, 990 II, 990H, 990K, 992G, 992K, 993K
D10N, D10R, D10T, D10T2, D9L
D10N, D10R, D10T, D10T2, D9L
854G, D10N, D10R, D10T, D10T2, D9L
854G, 854K, D11N, D11R, D11T
854G, 854K, D11N, D11R
D10N, D10R, D10T, D9L
D10N, D10R, D10T, D10T2, D9L
D10N, D10R, D9L
854G, D10N, D10R, D10T, D10T2, D9L
814F II, 824S, 834B, 836
4J8004
BEARING-SLEEVE
814F II, 824S, 834B, 836
814F II, 824S, 834B, 836
7J5322
BEARING
844H
844H
9J2607
BEARING
854G, 854K, D10, D11N, D11R, D11T
854G, 854K, D10, D11N, D11R, D11T
9J2606
BEARING
854G, 854K, D10, D11N, D11R, D11T
854G, 854K, D10, D11N, D11R, D11T
6N7045
BEARING--MAIN
992, D10, D348
992, D10, D348
6N7043
BEARING--MAIN (.050 IN. UNDERSIZE)
992, D10, D348
992, D10, D348
6N7044
BEARING--MAIN (.025 IN. UNDERSIZE)
992, D10, D348
992, D10, D348
6N3736
BEARING CENTER
D8H, D8K
D8H, D8K
6N3739
BEARING CENTER
D8H, D8K
D8H, D8K
D342, D342C, D8K