BEARING 9M3893 - Caterpillar

Electric Power Generation: 3512 (S/N: ZAF1-UP) 3512B (S/N: ZAH1-UP; ZAJ1-UP) 3516B (S/N: ZAP1-UP) 3516C (S/N: SBK1-UP) C175-16 (S/N: WYB1-UP)Engine: 3508 (S/N: CNF1-UP; 95Y1-UP; 23Z1-UP) 3508B (S/N: CBB1-UP; CNB1-UP; S2B1-UP; S2D1-UP; ZAD1-UP; S2E1-UP; 7SM1-UP; 6PN1-UP; 5PS1-UP; 1TW1-UP; 3DW1-UP; 5KW1-UP) 3508C (S/N: TTB1-UP) 3512 (S/N: PTH1-UP; CMJ1-UP; 2WK1-UP; FDR1-UP; 6WW1-UP; 50Y1-UP; 24Z1-UP; 65Z1-UP; 67Z1-UP) 3512B (S/N: CMC1-UP; FDE1-UP; BLF1-UP; PTF1-UP; PWG1-UP; S2H1-UP; S2J1-UP; S2K1-UP; S2L1-UP; 8RM1-UP; 4TN1-UP; 3ZW1-UP; 4AW1-UP; 6GW1-UP; YAY1-UP) 3512C (S/N: TTC1-UP; TTF1-UP; SBG1-UP; MKH1-UP; LLK1-UP; SLM1-UP; E3X1-UP) 3516 (S/N: CMD1-UP; ZAL1-UP; GZR1-UP; YAS1-UP; 3SS1-UP; 71Z1-UP; 72Z1-UP; 73Z1-UP) 3516B (S/N: CBN1-UP; FDN1-UP; PBR1-UP; S2R1-UP; ZAR1-UP; GZS1-UP; S2S1-UP; YAT1-UP; S2W1-UP; 2FW1-UP; 4BW1-UP; S2X1-UP) 3516C (S/N: TTD1-UP; PAG1-UP; TTH1-UP; SBJ1-UP; TTJ1-UP; TKY1-UP) G3508 (S/N: 9TG1-UP; CPJ1-UP; WPN1-UP; CPS1-UP; CPY1-UP) G3512 (S/N: 7NJ1-UP; CRN1-UP; WPP1-UP) G3516 (S/N: ZBA1-UP; 3RC1-UP; 4EK1-UP; WPT1-UP; WPW1-UP; CSZ1-UP) G3516B (S/N: ZBB1-UP; ZBC1-UP; JEF1-UP)Pumper: SPF343C (S/N: RTX1-UP)Excavator: 5230B (S/N: 4HZ1-UP)Hydraulic Shovel: 6060 (S/N: DHN1-UP)Motor Grader: 160M (S/N: B9L1-UP)Transmission: TH55 - KRESS (S/N: KCH1-UP)Off-Highway Truck/Tractor: 776D (S/N: AFS1-UP) 777D (S/N: DCB1-UP; AGC1-UP; FKR1-UP) 785C (S/N: APX1-UP) 785D (S/N: MSY1-UP) 789C (S/N: 2BW1-UP) 789D (S/N: SPD1-UP) 793C (S/N: CBR1-UP; ATY1-UP) 793F (S/N: SSP1-UP)Petroleum Engine: 3508C (S/N: LLC1-UP; LLE1-UP) 3512C (S/N: LLA1-UP; R1A1-UP; LLF1-UP) 3516C (S/N: PES1-UP)Power Module: PM3516 (S/N: BPD1-UP; KEN1-UP; NBR1-UP)Track-Type Tractor: D11R (S/N: AAF1-UP; 7PZ1-UP)Wheel Dozer: 854G (S/N: A4W1-UP)Wheel Loader: 992G (S/N: AZX1-UP; ADZ1-UP) 994D (S/N: 3TZ1-UP) 994F (S/N: 4421-UP)Introduction
Do not handle the water pumps until the entire Special Instruction has been read and understood.Correct handling of the water pump used on the serial numbers listed above is necessary. Improper handling of the water pump can cause cracking of the face seal group, resulting in very early hour failures.Water Pump Handling Procedures
Water pumps may leak as a result of damaged face seals. Relative movement between the shaft and the housing may allow the drive shaft to contact the face seal in the water pump. If contact occurs, the face seal will be damaged, and very early hour failures can result.
Illustration 1 g03673385
Cutout of a typical water pump
Illustration 2 g03673386
View A (1) Water pump shaft (2) Rubber seal (3) 416-0603 Seal Gp (4) Ceramic ring (5) Water pump housingNote: The 416-0603 Seal Gp is a service replacement for all older seal group designs.
Do NOT move the water pump shaft (1) in respect to the water pump housing (5) .
NEVER handle the water pump by the shaft.
Use special care when removing the water pump from the shipping container.
The water pump should NEVER be set down with the shaft on the ground or other surface
Do NOT bump the shaft when installing the pump on the engine. Always use a hoist when installing the pump on the engine.
NEVER use a hammer, mount, or other device on the water pump or on the shaft which might cause movement between the shaft and the housing.
Do NOT use the installation tool as described in Service Magazine, SEPD0390. Use of the tool may result in loosening of the impeller. Use of the tool may cause failure of the water seal if the bolts are