BEARING-SLEEVE 9R0614 - Caterpillar

Electric Power Generation:
G3520C (S/N: CWW1-UP; CWY1-UP)
SR4 (S/N: 5KA1-UP; 5NA1-UP; 6AA1-UP; 6FA1-UP; 9AB1-UP)
Engine:
3208 (S/N: 29A1-UP; 30A1-UP; 5YF1-UP)
3304 (S/N: 5CA1-UP; 83Z1-UP)
3304B (S/N: DED1-UP; 2KK1-UP; 9HK1-UP)
3306 (S/N: 85Z1-UP)
3306B (S/N: B8D1-UP; EFA1-UP; 1CZ1-UP; 2AJ1-UP; 8JJ1-UP; 8NS1-UP; 9DS1-UP; 9NR1-UP)
3406 (S/N: 75Z1-UP)
3406B (S/N: 2WB1-11475; 4JK1-0098; 4PM1-UP; 4RG1-1501)
3406C (S/N: KPS1-UP; PFH1-UP; 1DZ1-UP; 1LS1-UP; 2WB11476-UP; 4JK0099-UP; 4RG1502-UP; 4ZR1-UP; 8FS1-UP; 9ES1-UP)
3406E (S/N: 9NN1-UP; 8AZ1-UP)
3408 (S/N: 78Z1-1143)
3408B (S/N: 2BG1-UP; 78Z1144-UP)
3412 (S/N: 1EZ1-UP; 2WJ1-UP; 3FZ1-UP; 4BZ1-UP; 81Z1-14500)
3412C (S/N: BAK1-UP; BAX1-UP; BCW1-UP; 2SZ1-UP; 5FL1-UP; 81Z14501-UP; 9EP1-UP)
3456 (S/N: BGA1-UP; CAH1-UP; CBX1-UP; CCB1-UP; EPE1-UP; GHJ1-UP)
3508 (S/N: CNF1-UP; CAW1-UP; PTK1-UP; 1JZ1-UP; 1ZF1-UP; 23Z1-UP; 3LS1-UP; 5PW1-UP; 5XM1-UP; 70Z1-UP)
3508B (S/N: BGX1-UP; CNB1-UP; PTN1-UP; 1FZ1-UP; 2HW1-UP; 4GM1-UP; 5KW1-UP; 6PN1-UP)
3512 (S/N: CMJ1-UP; FDR1-UP; PTG1-UP; PTH1-UP; 1KZ1-UP; 24Z1-UP; 3MS1-UP; 3WS1-UP; 3YF1-UP; 6PM1-UP; 6WW1-UP; 67Z1-UP)
3512B (S/N: BLF1-UP; BRK1-UP; CMC1-UP; FDE1-UP; PTF1-UP; PTM1-UP; 1GZ1-UP; 4AW1-UP; 5AW1-UP; 6GW1-UP; 6WN1-UP; 8RM1-UP)
3516 (S/N: CAL1-UP; CMD1-UP; 1LZ1-UP; 2TS1-UP; 25Z1-UP; 3JS1-UP; 3NS1-UP; 4XF1-UP; 5SJ1-UP; 6CL1-UP; 7KM1-UP; 73Z1-UP; 8TW1-UP)
3516B (S/N: BMB1-UP; BPJ1-UP; CPA1-UP; FDN1-UP; FDX1-UP; PPS1-UP; 1HZ1-UP; 1NW1-UP; 2JW1-UP; 6HN1-UP; 7RN1-UP; 8NW1-UP)
G3306 (S/N: CNR1-UP)
G3406 (S/N: KAR1-UP)
G3412 (S/N: KAP1-UP)
G3508 (S/N: CPJ1-UP; CPS1-UP; CPY1-UP)
G3512 (S/N: CRN1-UP; CSP1-UP)
G3516 (S/N: CSZ1-UP)
G3516B (S/N: CEY1-UP; CME1-UP; CSC1-UP)
G3520B (S/N: BGW1-UP; CWD1-UP)
Power Module:
PM3412 (S/N: CAJ1-UP)
PM3456 (S/N: B3G1-UP)
PM3508 (S/N: BLM1-UP)
PM3512 (S/N: BNR1-UP; BRF1-UP)
PM3516 (S/N: BPD1-UP; CAC1-UP)
PMG3516 (S/N: CFD1-UP)
Voltage Adjustment - Single Unit Operation
Personal injury or death can result from high voltage.When power generation equipment must be in operation to make tests and/or adjustments, high voltage and current are present.Improper test equipment can fail and present a high voltage shock hazard to its user.Make sure the testing equipment is designed for and correctly operated for high voltage and current tests being made.When servicing or repairing electric power generation equipment:
Make sure the unit is off-line (disconnected from utility and/or other generators power service), and either locked out or tagged DO NOT OPERATE.
Remove all fuses.
Make sure the generator engine is stopped.
Make sure all batteries are disconnected.
Make sure all capacitors are discharged.Failure to do so could result in personal injury or death. Make sure residual voltage in the rotor, stator and the generator is discharged.
Remove the generator's access panel.
Remove the sealing screws in order to gain access to the Level and Gain Adjustment Controls.
Turn the Gain Control counter-clockwise to zero. After turning the Gain Control counterclockwise to zero, turn the Gain Control five turns clockwise.
Perform the required maintenance on the engine prior to starting the engine.
Start the engine and allow the engine to warm up.
Increase the engine speed to the engine's full-governed speed (high idle).
Connect a voltmeter. Observe the voltmeter reading. If the desired voltage is not indicated, set the no-load voltage with level control.
Close the circuit breaker and gradually apply full load. Adjust the governor control until nameplate frequency is indicated on the frequency meter or until an engine tachometer indicates rated speed.Note: Full load must be applied to properly adjust regulator.
With full load applied, perform one of the following two steps.
If voltmeter reading increases with full load applied, turn the gain control in a counter-clockwise direction.
If voltmeter reading decreases with full load applied, turn the gain control in a clockwise direction.
Remove load. If necessary, adjust the