BEARING FRONT CRANKSHAFT 9S3663 - Caterpillar

Ensure that all safety information, warnings, and instructions are read and understood before any operation or any maintenance procedures are performed. The user is responsible for the performance of maintenance, including all adjustments, the use of proper lubricants, fluids, and filters. The user is also responsible for the replacement of components due to normal wear and aging. Failure to adhere to proper maintenance intervals and procedures may result in diminished performance of the product and/or accelerated wear of components. Use fuel consumption, service hours, or calendar time, WHICH EVER OCCURS FIRST, to determine the maintenance intervals. Products that operate in severe operating conditions may require more frequent maintenance. Before each consecutive interval is performed, all maintenance from the previous interval must be performed.When Required
Automatic Start/Stop - Inspect
Battery - Recycle
Battery - Replace
Battery or Battery Cable - Disconnect
Coolant Sample (Level 2) - Obtain
Engine Air Cleaner Element (Single Element) - Inspect/Clean/Replace
Engine Oil - Change
Fuel Metering Valve - Check
Generator - Dry
Generator Set - Test
Generator Set Alignment - Check
Generator Winding - Test
Overhaul Considerations
Space Heater - Test
Stator Winding Temperature - Test
Throttle Control Valve - Check
Generator Lead - Check
Daily
Air Tank Moisture and Sediment - Drain
Electrical Connections - Check
Engine Air Cleaner Service Indicator - Inspect
Engine Oil Level - Check
Fuel Filter Differential Pressure - Check
Fumes Disposal Filter Differential Pressure - Check
Generator Bearing Temperature - Test/Record
Jacket Water Heater - Check
Power Factor - Check
Voltage and Frequency - Check
Coolant Level - Check
Walk-Around Inspection
Generator Load - Check
Initial 250 Service Hours
Cylinder Pressure - Test/Record
Every 250 Service Hours
Battery Charger - Check
Coolant Sample (Level 1) - Obtain
Engine Oil Sample - Obtain
Fumes Disposal Filter - Drain
Battery Electrolyte Level - Check
Cooling System Supplemental Coolant Additive (SCA) - Test/Add
Every 1000 Service Hours
Aftercooler Condensation - Drain
Alternator - Inspect
Belts - Inspect/Adjust/Replace
Crankcase Pressure - Measure
Engine Crankcase Breather - Clean
Engine Oil Filter - Change
Engine Speed/Timing Sensor - Clean/Inspect
Engine Valve Lash and Bridge - Check
Flexible Coupling - Inspect
Gas Pressure Regulator Condensation - Drain
Generator Winding Insulation - Test
Hoses and Clamps - Inspect/Replace
Inlet Air System - Check
Radiator - Clean
Valve Stem Projection - Measure/Record
Water Pump - Inspect
Every 2000 Service Hours
Carburetor Air/Fuel Ratio - Check/Adjust
Compressor Bypass - Check
Stator Lead - Check
Generator - Inspect
Generator Bearing - Lubricate
Generator Set Vibration - Inspect
Generator Set Vibration - Test/Record
Spark Plugs - Inspect/Replace
Every 3000 Service Hours
Spark Plugs - Inspect/Replace
Every 4000 Service Hours
Crankcase Blowby - Test/Record
Cylinder Pressure - Test/Record
Engine Mounts - Inspect
Engine Protective Devices - Check
Starting Motor - Inspect
Ignition System Timing - Check/Adjust
Between 7500 and 8000 Service Hours
Overhaul (Top End)
Every 8000 Service Hours
Coolant Temperature Regulator - Replace
Fumes Disposal Filter Element - Replace
Rotating Rectifier - Inspect/Test
Turbocharger - Inspect
Varistor - Check
Every 10 000 Service Hours
Generator Bearing - Inspect
Between 10 000 and 20 000 Service Hours
Engine Oil Temperature Regulator - Replace
Between 22 500 and 24 000 Service Hours
Overhaul (In-Frame)
Every 24 000 Service Hours or 3 Years
Coolant (NGEC) - Change
Between 37 500 and 40 000 Service Hours
Overhaul (Major)