9S6924 BEARING-SPECIAL BALL Caterpillar parts
910, 931B, D3B, G910, IT12
Rating:
Alternative (cross code) number:
CA9S6924
9S-6924
9S6924
CA9S6924
9S-6924
9S6924
Weight: 0.60 pounds 0 kg.
COMPACT WHEEL LOADER, WHEEL LOADER,
Compatible equipment models: 9S6924:
For full view, you need register
Information:
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
B 164-5924 Injector Bore Gauge 1
C 164-5927 Brush 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01082129Note: Refer to Special Instruction, REHS0116, "Removal and Installation of HEUI Injectors" for information for the removal of the carbon from the unit injector sleeve.
Use Tooling (B) to check the amount of carbon in the unit injector sleeve. Tooling (B) must come in contact with the top of unit injector sleeve (10). Use Tooling (C) to remove carbon in the seat of the unit injector.
Install the O-ring seals on the unit injector.
Lubricate the O-ring seals with clean engine oil.
Illustration 2 g01082133
Install unit injector (9) in the cylinder head.
Illustration 3 g01082121
Install clamp (7) and bolt (6).
Install O-ring seals (5) and (8).
Lubricate O-ring seals (5) and (8) with clean engine oil.
Illustration 4 g01082118
Illustration 5 g01082135
Install elbow (2), bolts (1), and capscrews (3).
If cap (11) was removed for any reason, tighten the bolts for the unit injector to the following torques:
Tighten Capscrews (3) to a torque of 1 0.2 N m (9 2 lb in).
Tighten Bolts (12) to a torque of 5 3 N m (44 27 lb in).
Tighten Bolts (1) to a torque of 5 3 N m (44 27 lb in).
Again, tighten Capscrews (3) to a torque of 12 3 N m (9 2 lb ft).
Again, tighten Bolts (12) to a torque of 47 9 N m (35 7 lb ft).
Again, tighten Bolts (1) to a torque of 47 9 N m (35 7 lb ft).
Install harness assembly (4). Note: Make sure that you use the correct harness assembly for the correct cylinder.Note: The harness assembly that is for the injector toward the front of the base is marked with white paint. The harness assembly that is for the injector toward the rear of the base is marked with a small "R".Tighten the nuts for harness assembly (4) to a torque of 1.70 0.25 N m (15 2 lb in).End By:
Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism Cover - Remove and Install".
Table 1
Required Tools
Tool Part Number Part Description Qty
B 164-5924 Injector Bore Gauge 1
C 164-5927 Brush 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01082129Note: Refer to Special Instruction, REHS0116, "Removal and Installation of HEUI Injectors" for information for the removal of the carbon from the unit injector sleeve.
Use Tooling (B) to check the amount of carbon in the unit injector sleeve. Tooling (B) must come in contact with the top of unit injector sleeve (10). Use Tooling (C) to remove carbon in the seat of the unit injector.
Install the O-ring seals on the unit injector.
Lubricate the O-ring seals with clean engine oil.
Illustration 2 g01082133
Install unit injector (9) in the cylinder head.
Illustration 3 g01082121
Install clamp (7) and bolt (6).
Install O-ring seals (5) and (8).
Lubricate O-ring seals (5) and (8) with clean engine oil.
Illustration 4 g01082118
Illustration 5 g01082135
Install elbow (2), bolts (1), and capscrews (3).
If cap (11) was removed for any reason, tighten the bolts for the unit injector to the following torques:
Tighten Capscrews (3) to a torque of 1 0.2 N m (9 2 lb in).
Tighten Bolts (12) to a torque of 5 3 N m (44 27 lb in).
Tighten Bolts (1) to a torque of 5 3 N m (44 27 lb in).
Again, tighten Capscrews (3) to a torque of 12 3 N m (9 2 lb ft).
Again, tighten Bolts (12) to a torque of 47 9 N m (35 7 lb ft).
Again, tighten Bolts (1) to a torque of 47 9 N m (35 7 lb ft).
Install harness assembly (4). Note: Make sure that you use the correct harness assembly for the correct cylinder.Note: The harness assembly that is for the injector toward the front of the base is marked with white paint. The harness assembly that is for the injector toward the rear of the base is marked with a small "R".Tighten the nuts for harness assembly (4) to a torque of 1.70 0.25 N m (15 2 lb in).End By:
Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism Cover - Remove and Install".
Caterpillar parts catalog:
Parts bearing Caterpillar catalog:
3P, 3S, 54, 613C, 613C II, 613G, 910, 931B, 933, 939, D3B, D3C II, D3C III, D4C III, D5C III
594, 931B, 931C, 931C II, 933, 935B, 939, D3B, D3C, D3C II, D3C III, D4C, D4C III, D5, D5C, D5C III, D6C, D7F, D8H, D9G
3P, D3B, D3C III, D4B, D4C, D4C II, D4C III, D5C, D5C III
627, 657B, 666B, 772, 773, 814, 910, 910E, 931B, 931C, 933, 935C, 939, 950, 966C, 980, 980B, 988, D3B, D3C II, D3C III, D4C, D4C III, D5C III, IT12B, R1300, R1300G, R1300G II, R1600, R1600G, R1600H, R...
3S, 4S, 5S, 6A, 955C, 955H, 977D, D3B, D4E, D5B, D7H
910, 931B, D3, IT12
931B, D3B, D4D
508, 518, 527, 931B, D5HTSK II, D9H
910, 931B
910, 910E, 910G, IT12B, IT14B, IT14F
814B, 815B, 826C, 834B, 836, 910, 916, 920, 926, 930, 930R, 936, 936F, 950, 950B, 950F, 950F II, 966C, 966D, 966F, 966R, 980B, 980C, 980F, 980F II, 988B, 992C, 994, CS-643, D25C, D30C, D350C, D35C, D3...
814B, 815B, 824C, 826C, 834B, 836, 910, 916, 926, 936, 936F, 950B, 950F, 950F II, 966D, 966F, 980C, 980F, 988B, 992C, 994, G936, IT18B, IT28B
657, 666, 769, 824, 834, 910, 931, 931B, 988, D3B, D3C II
14G, 14H, 14H NA, 16G, 16H, 16H NA, 518, 518C, 528, 528B, 530B, 578, 583R, 589, 613C, 613C II, 613G, 910, 916, 920, 930, 931B, 931C, 931C II, 933, 941, 951B, D3B, D3C, D3C III, D4B, D4C, D4C III, D4D,...
578, 583R, 589, 906H, 906H2, 907H, 907H2, 908H, 908H2, 910, 931, 931B, D3B, D3C II, G910, IT12
910, 931, 931B, D3B, D3C II, G910, IT12
12F, 12G, 141, 14E, 153, 16, 515, 518, 518C, 525, 525B, 525C, 528, 528B, 530B, 535B, 535C, 545, 545C, 561D, 571G, 572G, 578, 583K, 583R, 587R, 589, 594, 594H, 613, 613B, 613C, 615, 615C, 826B, 834B, 8...
910, 916, 926, 931B, 931C, 931C II, 933, 939, D3B, D3C, D3C III, D4B, D4C, D4C III, D5C, D5C III, G910, G916, G926, IT12, IT18, IT18B, IT28, IT28B
517, 527, 561M, 561N, 572R, 572R II, 583R, 587R, 587T, 814, 815, 910, 916, 926, 931B, 931C, 931C II, 933, 939, 950, 955K, 955L, 966C, D3B, D3C III, D4B, D4C, D4C III, D4H, D4H XL, D4HTSK II, D4HTSK II...
910, 916, 926, 926A, 931B, 931C, 931C II, 933, 939, D3B, D3C, D3C III, D4B, D4C, D4C III, D4H, D4HTSK II, D5C, D5C III, G910, G926, IT12, IT18B, IT28, IT28B
931B, 933, 966K, 966M XE, 972M XE, D3B, D3C III, D4B, D4C III
515, 525, 561M, 561N, 621, 621B, 621E, 621F, 621G, 621H, 621K, 621R, 623B, 623E, 623F, 623G, 623H, 623K, 623K LRC, 627B, 627E, 627F, 627G, 627H, 627K, 627K LRC, 631C, 631E, 631G, 633D, 633E II, 637D, ...
6V2753
BEARING
14G, 916, 926, 931B, D3B, D4B, G916, IT18, IT18B, IT28
14G, 916, 926, 931B, D3B, D4B, G916, IT18, IT18B, IT28