9W7919 BEARING-SLEEVE Caterpillar parts
Rating:
Alternative (cross code) number:
CA9W7919
9W-7919
9W7919
CA9W7919
9W-7919
9W7919
Weight: 4 pounds 2 kg.
Information:
ID
182.4
mm
OD
192.4
mm
WIDTH
96
mm
Related part:
9W7919
BEARING-SLV-YM
4253647
CL
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
CTP 9W7919 Sleeve Bearing for Heavy Equipment
CTP Sleeve Bearing Only || Sold in each || Easy in-and-out fit
CTP Sleeve Bearing Only || Sold in each || Easy in-and-out fit
CTP 9W7919 Sleeve Bearing for Heavy Equipment
CTP Sleeve Bearing Only || Sold in each || Easy in-and-out fit
CTP Sleeve Bearing Only || Sold in each || Easy in-and-out fit
Information:
View A-A(1) Install bolts to hold wheels and tighten in sequence shown to a torque of ... 70 15 N m (50 11 lb ft) Then tighten bolts again in same sequence to a torque of ... 1125 100 N m (820 75 lb ft)(2) Put 9S3263 Thread Lock on threads of bolts and tighten to a torque of ... 20 4 N m (15 3 lb ft)(3) Put 9S3263 Thread Lock on threads of bolts and tighten by hand in sequence shown. Then tighten bolts again in same sequence to a torque of ... 25 7 N m (18 5 lb ft)(4) Torque for nut ... 68 7 N m (50 5 lb ft) See Procedure to Adjust Bearings
Section B-B(5) Rubber toric seals and all surfaces in contact with them must be clean and dry at assembly. Put a thin layer of oil on the surfaces of the metal seals that are in contact just before installation. Metal seal rings must be square with the bore and rubber toric seals must not be bulged or twisted. Put lubricant on all other seals at assembly. Procedure to Adjust Bearings1. Install hub with inner bearing on spindle. Then install outer bearing on spindle loose. Install washer, lockwasher, and nut (4) on spindle.2. Tighten nut (4) to a torque of 68 7 N m (50 5 lb ft).3. Rotate hub two full revolutions.4. Do Steps 2 and 3 again three more times in sequence.5. After nut (4) has been tightened the final time, bend a tang of lockwasher into slot of nut (4). If a tang of lockwasher is not in alignment with a slot of nut (4), then tighten nut (4) until the most nearly aligned tang is in alignment with a slot.
Caterpillar SIS machinery equipment:
Caterpillar SIS
D9R Track-Type Tractor Differential Steering 7TL00001-00556 (MACHINE) POWERED BY 3408 Engine »
9W-7919
KIT-FINAL DRIVE BEARING
D9R Track-Type Tractor Power Shift 8BL00830-01052 (MACHINE) POWERED BY 3408 Engine »
9W-7919
KIT-FINAL DRIVE BEARING
D9R Track-Type Tractor Differential Steering 7TL00557-00851 (MACHINE) POWERED BY 3408 Engine »
9W-7919
KIT-FINAL DRIVE BEARING
D9R Track-Type Tractor Power Shift 8BL01053-UP (MACHINE) POWERED BY 3408 Engine »
9W-7919
KIT-FINAL DRIVE BEARING
D9R Track-Type Tractor Differential Steering 7TL00852-UP (MACHINE) POWERED BY 3408 Engine »
9W-7919
KIT-FINAL DRIVE BEARING
D9R Track-Type Tractor Differential Steering ABK00001-UP (MACHINE) POWERED BY 3408 Engine »
9W-7919
KIT-FINAL DRIVE BEARING
Parts bearing Caterpillar catalog:
9W6438
BEARING
Caterpillar
Caterpillar
9W6437
BEARING
Caterpillar
Caterpillar
9W5782
BEARING LUBE
Caterpillar
Caterpillar
9W5780
BEARING
Caterpillar
Caterpillar
9W5639
BEARING A=
Caterpillar
Caterpillar
9W4708
BEARING
Caterpillar
Caterpillar
9W9994
BEARING
Caterpillar
Caterpillar
9W9993
BEARING
Caterpillar
Caterpillar
9W9992
BEARING
Caterpillar
Caterpillar
9W9832
BEARING
Caterpillar
Caterpillar
9W9308
BEARING-SLEEVE
Caterpillar
Caterpillar
9W7949
BEARING
Caterpillar
Caterpillar