9Y0199 BEARING-CONNECTING ROD Caterpillar parts
3176
Rating:
Alternative (cross code) number:
CA9Y0199
9Y-0199
9Y0199
CA9Y0199
9Y-0199
9Y0199
Weight: 0.70 pounds 0 kg.
TRUCK ENGINE,
Compatible equipment models: 9Y0199:
Number on catalog scheme:
3
For full view, you need register
Information:
Introduction
The problem that is identified below does not have a known permanent solution. Until a permanent solution is known, use the solution that is identified below.Problem
The existing oil hoses are failing due to both heat exposure and abrasion.Solution
The new 423-4640 Hose As and 423-4641 Hose As are a direct replacement for the existing 148-2104 Hose As and 144-0119 Hose As . Refer to Table 1 for a list of parts needed to install the new hose assemblies.The removal procedure for existing hoses and the installation procedure for the new installing the new hose assemblies is shown below.
Table 1
New Part Number Description Quantity
319-6220 Elbow As 1
423-4640 Hose As 1
423-4641 Hose As 1
228-7093 O-Ring Seal 1
6V-1889 Clip 4
8T-7088 Grommet 3
204-2281 Cable Strap 3 Note: If either of the 148-2104 Hose As or 144-0119 Hose As fail, replacing all existing part numbers with the new parts is required.Removal and Installation Procedure
Illustration 1 g03340064
(1) Seal O-Ring (2) Clips (Retain the Bolts and Washers for reassembly) (3) Hose Assembly (4) Seal O-Ring (5) Adapter
Remove the hose assemblies and mounting hardware indicated in Illustration 1.
Illustration 2 g03340934
(6) 228-7093 O-Ring Seal (7) 423-4641 Hose As (8) 423-4640 Hose As (9) Two 8T-7088 Grommets (10) Two 204-2281 Cable Straps (11) Two 6V-1889 Clips (12) Two 8T-4121 Hard Washers (13) 8T-4136 Bolt (14) 8T-4133 Nut (15) 319-6220 Elbow As
Connect hoses (7) and (8) to the remote oil filter base.Note: New O-ring (6) must be used connecting hose (8) .
Route hoses (7) and (8) and secure the hoses to the bracket where shown using clips (11), washers (12), bolts (13), and nut (14) .Note: Bolts (113) and washers (12) were retained from the removal of the old parts.
Install connector (15) into the oil line adapter. Connect the hoses to the connectors as shown.
Install grommets (9) and cable straps (10) as shown in Illustration 2.
The problem that is identified below does not have a known permanent solution. Until a permanent solution is known, use the solution that is identified below.Problem
The existing oil hoses are failing due to both heat exposure and abrasion.Solution
The new 423-4640 Hose As and 423-4641 Hose As are a direct replacement for the existing 148-2104 Hose As and 144-0119 Hose As . Refer to Table 1 for a list of parts needed to install the new hose assemblies.The removal procedure for existing hoses and the installation procedure for the new installing the new hose assemblies is shown below.
Table 1
New Part Number Description Quantity
319-6220 Elbow As 1
423-4640 Hose As 1
423-4641 Hose As 1
228-7093 O-Ring Seal 1
6V-1889 Clip 4
8T-7088 Grommet 3
204-2281 Cable Strap 3 Note: If either of the 148-2104 Hose As or 144-0119 Hose As fail, replacing all existing part numbers with the new parts is required.Removal and Installation Procedure
Illustration 1 g03340064
(1) Seal O-Ring (2) Clips (Retain the Bolts and Washers for reassembly) (3) Hose Assembly (4) Seal O-Ring (5) Adapter
Remove the hose assemblies and mounting hardware indicated in Illustration 1.
Illustration 2 g03340934
(6) 228-7093 O-Ring Seal (7) 423-4641 Hose As (8) 423-4640 Hose As (9) Two 8T-7088 Grommets (10) Two 204-2281 Cable Straps (11) Two 6V-1889 Clips (12) Two 8T-4121 Hard Washers (13) 8T-4136 Bolt (14) 8T-4133 Nut (15) 319-6220 Elbow As
Connect hoses (7) and (8) to the remote oil filter base.Note: New O-ring (6) must be used connecting hose (8) .
Route hoses (7) and (8) and secure the hoses to the bracket where shown using clips (11), washers (12), bolts (13), and nut (14) .Note: Bolts (113) and washers (12) were retained from the removal of the old parts.
Install connector (15) into the oil line adapter. Connect the hoses to the connectors as shown.
Install grommets (9) and cable straps (10) as shown in Illustration 2.
Caterpillar parts catalog:
Parts bearing Caterpillar catalog:
120H, 120H NA, 12H, 12H NA, 135H, 135H NA, 140H, 140H NA, 140K, 14H NA, 160H, 160H NA, 160K, 1673C, 215B, 235, 3114, 3116, 3126, 3126B, 3176, 3176B, 3176C, 3196, 3208, 320B, 325B L, 3304, 3304B, 3306,...
120G, 130G, 1673C, 1676, 1693, 3176, 3306, 3306C, 3406, 3406B, 3406C, 3408, 3408C, 3408E, 3412, 528, 613, 613B, 623F, 920, 930, 950, 950B, 966C, 980B, D9G
1673C, 3176, 3176B, 3176C, 3196, 3208, 3306, 3306C, 3406, 3406B, 3406C, 3406E, 3408, 3408C, 3408E, 3412, 3456, 623F, 980B, C-10, C-12, C-15, C-16, D6C
3176, 3176B, 75, 75C, 85C, R1700 II
3176, 3176B, 75, 75C, 85C, R1700 II
3176, 3176B, 75, 75C, 85C, R1700 II
3176, 3176B, 75, 75C, 85C, R1700 II
140H, 143H, 14H, 14M, 160H, 163H, 16H, 16M, 3176, 3176B, 3176C, 3196, 345B, 345B II, 345B II MH, 345B L, 345C, 345C L, 345C MH, 345D, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L, 349E L HVG, 349E L ...
3176, 3176B, 75, 75C, 85C, R1700 II
3176, 3176B, 75, 75C, 85C, R1700 II
140H, 143H, 14H, 160H, 163H, 3176, 3176B, 3176C, 345B, 345B II, 345B II MH, 345B L, 480, 572R II, 65E, 725, 75, 75C, 75D, 75E, 814F, 815F, 816F, 85C, 966G II, C-10, CPT372, D7R II, R1600, R1600G, R170...
12H ES, 140G, 140H, 140H ES, 140H NA, 143H, 14H NA, 160H, 160H ES, 160H NA, 163H NA, 3176, 3176B, 3176C, 3306, 480, 528B, 530B, 65E, 75, 75C, 75D, 75E, 85C, C-10, D6E SR, D6H, D6H XL, D6H XR, D7H, R17...
3114, 3116, 924F, 963B, AP-1000, AP-1050, CB-634C, CP-563, CS-533C, CS-563C, CS-573C, CS-583C, IT24F, M318, M320
213B, 214B, 3116, 320 L, 325, 325B, 918F, 928F, 938F, 950F, CP-563, CS-533
3116, 3126
3116, 3126, 3126B, 325D, 330D, C-9, C7, C9, CX31-C9I, PM-102, TH31-E61
2W3633
BEARING-ROLLER
3406B
3406B
3176, 3176B, 3406B, 3406C, 3406E, C-10, C-12
1064337
BEARING-THRUST
3114, 3116
3114, 3116
7C9537
BEARING
330B, 3406B, 3406C, 350, 966G, 970F, D6H, D6R, D7H
330B, 3406B, 3406C, 350, 966G, 970F, D6H, D6R, D7H
3116
205B, 213B, 3116, 320 L, 918F, 938F, 950F, E200B
