1937732 BELT TENSIONER Caterpillar parts
3512C, 814F, 815F, 816F, 966G II, 972G II, C-10, C-12
Rating:
Alternative (cross code) number:
CA1937732
193-7732
1937732
CA1937732
193-7732
1937732
Weight: 3 pounds 1 kg.
INDUSTRIAL ENGINE, WHEEL LOADER,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
Belt Tensioner 193-7732 1937732 for Caterpillar C10 C12 Engine
MGADOSIA Part Number: 193-7732 1937732 || Applicable models: Fit for Caterpillar C10 C12 Engine || Safety: 100% Tested Before Shipping to Ensure Product Safety, Stability and Durability. || Function: High-quality material for long-lasting durability. Perfect match for the original car and easy to install || TIPS: Please be sure to compare carefully with photos and check part number before buying items, If you are not sure this part is suitable, please feel free to contact us, we'll reply you as soon as possible.
MGADOSIA Part Number: 193-7732 1937732 || Applicable models: Fit for Caterpillar C10 C12 Engine || Safety: 100% Tested Before Shipping to Ensure Product Safety, Stability and Durability. || Function: High-quality material for long-lasting durability. Perfect match for the original car and easy to install || TIPS: Please be sure to compare carefully with photos and check part number before buying items, If you are not sure this part is suitable, please feel free to contact us, we'll reply you as soon as possible.
Compatible equipment models: 1937732:
Information:
Engine Crankshaft Will Not Turn
Possible Causes/Corrections
Low or No Battery Voltage/Check battery voltage. If battery voltage is less than 8 volts for a 12 volt system, or 16 volts for a 24 volt system, put a charge to the battery. If battery will not hold a charge, load test the battery as shown in the ELECTRICAL SYSTEM of the Testing and Adjusting section of this Service Manual. Bad Switch, Bad Wiring or Connection in Switch Circuit/With ignition switch in START position, check voltage at switch connection on starter solenoid. If there is no voltage, or if the voltage is low at this connection, check wiring, connections, ignition switch, and magnetic switch (if used). Bad Cable or Connection; Battery to Starter/With ignition switch in the START position, check voltage at connection of battery cable to starter. If there is no voltage, or if the voltage is low at this connection and there is good voltage at the battery, check for bad cable or connection between the battery and the starter. Bad Starter Solenoid/Remove and repair a solenoid which does not work when voltage is correct at both the battery and ignition switch connections. Bad Starter Motor/If the solenoid works and the starter motor does not turn the crankshaft, the starter motor is bad. Before removing the starter motor, turn the crankshaft by hand to be sure a mechanical failure inside the engine, transmission, or power take-off is not preventing the crankshaft from turning. If crankshaft turns freely by hand, engage the starter motor again. If the starter motor still will not work, remove the starter motor and repair it, or install a new starter motor. Transmission or Power Take-off (if so equipped) Problem Prevents Crankshaft From Turning/If crankshaft can not be turned by hand, disconnect the transmission and power take-off. If crankshaft will now turn, find the cause of the problem in the transmission or power take-off and make necessary corrections. Inside Problem Prevents Engine Crankshaft From Turning/If the crankshaft can not be turned after disconnecting the transmission and power take-off, remove the fuel nozzles and check for fluid in the cylinders while turning the crankshaft. If fluid in the cylinders is not the problem, the engine must be disassembled to check for other inside problems. Some of these inside problems are bearing seizure, piston seizure, and valves making contact with pistons.Engine Crankshaft Turns Too Slowly
Possible Causes/Corrections
Low Battery Voltage/Check battery voltage. If battery voltage is less than 8 volts for a 12 volt system, or 16 volts for a 24 volt system, put a charge to the battery. If the battery will not hold a charge, load test the battery as shown in the ELECTRICAL SYSTEM of the Testing and Adjusting section of this Service Manual. Bad Cable or Connection; Battery to Starter/With switch in START position, check voltage at battery cable connection to starter. If voltage is low at this connection and there is good voltage at the battery, check for bad cable or connection between the battery and
Possible Causes/Corrections
Low or No Battery Voltage/Check battery voltage. If battery voltage is less than 8 volts for a 12 volt system, or 16 volts for a 24 volt system, put a charge to the battery. If battery will not hold a charge, load test the battery as shown in the ELECTRICAL SYSTEM of the Testing and Adjusting section of this Service Manual. Bad Switch, Bad Wiring or Connection in Switch Circuit/With ignition switch in START position, check voltage at switch connection on starter solenoid. If there is no voltage, or if the voltage is low at this connection, check wiring, connections, ignition switch, and magnetic switch (if used). Bad Cable or Connection; Battery to Starter/With ignition switch in the START position, check voltage at connection of battery cable to starter. If there is no voltage, or if the voltage is low at this connection and there is good voltage at the battery, check for bad cable or connection between the battery and the starter. Bad Starter Solenoid/Remove and repair a solenoid which does not work when voltage is correct at both the battery and ignition switch connections. Bad Starter Motor/If the solenoid works and the starter motor does not turn the crankshaft, the starter motor is bad. Before removing the starter motor, turn the crankshaft by hand to be sure a mechanical failure inside the engine, transmission, or power take-off is not preventing the crankshaft from turning. If crankshaft turns freely by hand, engage the starter motor again. If the starter motor still will not work, remove the starter motor and repair it, or install a new starter motor. Transmission or Power Take-off (if so equipped) Problem Prevents Crankshaft From Turning/If crankshaft can not be turned by hand, disconnect the transmission and power take-off. If crankshaft will now turn, find the cause of the problem in the transmission or power take-off and make necessary corrections. Inside Problem Prevents Engine Crankshaft From Turning/If the crankshaft can not be turned after disconnecting the transmission and power take-off, remove the fuel nozzles and check for fluid in the cylinders while turning the crankshaft. If fluid in the cylinders is not the problem, the engine must be disassembled to check for other inside problems. Some of these inside problems are bearing seizure, piston seizure, and valves making contact with pistons.Engine Crankshaft Turns Too Slowly
Possible Causes/Corrections
Low Battery Voltage/Check battery voltage. If battery voltage is less than 8 volts for a 12 volt system, or 16 volts for a 24 volt system, put a charge to the battery. If the battery will not hold a charge, load test the battery as shown in the ELECTRICAL SYSTEM of the Testing and Adjusting section of this Service Manual. Bad Cable or Connection; Battery to Starter/With switch in START position, check voltage at battery cable connection to starter. If voltage is low at this connection and there is good voltage at the battery, check for bad cable or connection between the battery and
Caterpillar parts catalog:
Parts belt Caterpillar catalog:
1900634
BELT TENSIONER
3116, C-10, C-12, C9, MTC735
3116, C-10, C-12, C9, MTC735
1333545
BELT TENSIONER
3176C, 3196, C-10, C-12, CPT372
3176C, 3196, C-10, C-12, CPT372
1333544
BELT TENSIONER
3176C, 3196, 3512C, 793D, 797B, 854G, 992G, 994F, 994H, C-10, C-12
3176C, 3196, 3512C, 793D, 797B, 854G, 992G, 994F, 994H, C-10, C-12
1481974
BELT TENSIONER
3176C, 3196, C-10, C-12
3176C, 3196, C-10, C-12
1900649
BELT TENSIONER
12M, 140G, 140H, 140M, 143H, 14H, 160H, 163H, 16H, 3126B, 3126E, 3176C, 3196, 3406E, 385B, 5090B, 725, 730, AD30, BG-2455D, C-10, C-12, C-15, C-16, C-18, C15, C18, C7, C9, CX31-C9I, CX35-P800, TH31-E6...
12M, 140G, 140H, 140M, 143H, 14H, 160H, 163H, 16H, 3126B, 3126E, 3176C, 3196, 3406E, 385B, 5090B, 725, 730, AD30, BG-2455D, C-10, C-12, C-15, C-16, C-18, C15, C18, C7, C9, CX31-C9I, CX35-P800, TH31-E6...
1421987
BELT TENSIONER
C-10, C-12
C-10, C-12
2117878
BELT-SERPENTINE
C-10, C-12, D6N LGP, D6N OEM
C-10, C-12, D6N LGP, D6N OEM
2002279
BELT TENSIONER
3406E, 583T, 587T, C-12, C-15, C-16, C-9, C13, C15, D8T, TH35-C13T
3406E, 583T, 587T, C-12, C-15, C-16, C-9, C13, C15, D8T, TH35-C13T
2534531
BELT-SERPENTINE
950H, 962H, 966G II, 972G II, C15, D5R LGP, D6N, IT62H
950H, 962H, 966G II, 972G II, C15, D5R LGP, D6N, IT62H
1892218
BELT-SERPENTINE
966G II, 972G II
966G II, 972G II
2269380
BELT-SERPENTINE
966G II, 972G II
966G II, 972G II
2606107
BELT-SERPENTINE
966G II, 972G II
966G II, 972G II
1964195
BELT TENSIONER
3126B, 3126E, C-10, C-12
3126B, 3126E, C-10, C-12
1421987
BELT TENSIONER
C-10, C-12
C-10, C-12
1900649
BELT TENSIONER
12M, 140G, 140H, 140M, 143H, 14H, 160H, 163H, 16H, 3126B, 3126E, 3176C, 3196, 3406E, 385B, 5090B, 725, 730, AD30, BG-2455D, C-10, C-12, C-15, C-16, C-18, C15, C18, C7, C9, CX31-C9I, CX35-P800, TH31-E6...
12M, 140G, 140H, 140M, 143H, 14H, 160H, 163H, 16H, 3126B, 3126E, 3176C, 3196, 3406E, 385B, 5090B, 725, 730, AD30, BG-2455D, C-10, C-12, C-15, C-16, C-18, C15, C18, C7, C9, CX31-C9I, CX35-P800, TH31-E6...
1481974
BELT TENSIONER
3176C, 3196, C-10, C-12
3176C, 3196, C-10, C-12
1333544
BELT TENSIONER
3176C, 3196, 3512C, 793D, 797B, 854G, 992G, 994F, 994H, C-10, C-12
3176C, 3196, 3512C, 793D, 797B, 854G, 992G, 994F, 994H, C-10, C-12
1333545
BELT TENSIONER
3176C, 3196, C-10, C-12, CPT372
3176C, 3196, C-10, C-12, CPT372
1333529
BELT TENSIONER
C-10, C-12
C-10, C-12
1340642
BELT TENSIONER
3306C
3306C
1570096
BELT TENSIONER
C-10, C-12
C-10, C-12
1602296
BELT TENSIONER
C-10, C-12
C-10, C-12
2117878
BELT-SERPENTINE
C-10, C-12, D6N LGP, D6N OEM
C-10, C-12, D6N LGP, D6N OEM