2173031 BELT-SERPENTINE Caterpillar parts
938G II, 950H, 962H, IT38G II, IT62H
Rating:
Alternative (cross code) number:
CA2173031
217-3031
2173031
CA2173031
217-3031
2173031
Weight: 0.60 pounds 0 kg.
Information:
BELT SIZE
.16
mm
EFFECTIVE LENGTH
2594
mm
NUMBER OF RIBS
8
CROSS SECTION
PK
INTEGRATED TOOLCARRIER, WHEEL LOADER,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
AG Shock Absorber Compatible for Ford F-150 15-20 Del Izq
AG Shock Absorber AG Compatible For Ford F-150 2015-2020 Front Left || Pressurized nitrogen gas technology. This compound is best for shock absorbers, as they have a much higher heat tolerance to hydraulics. This allows them to better dampen and also extends the life of the damper. || Stem with micropolished chrome layer for better slip and reduced wear. Revolutionized multi-lip seal for improved sealing system efficiency. || Manufactured to the same specifications and load values as the original OEM shock absorbers. || Quality Warranty: 4 years against manufacturing defects directly with us. Satisfaction Guarantee, you have 15 days to try them. If you do not have it, we exchange them to you or return your money!
AG Shock Absorber AG Compatible For Ford F-150 2015-2020 Front Left || Pressurized nitrogen gas technology. This compound is best for shock absorbers, as they have a much higher heat tolerance to hydraulics. This allows them to better dampen and also extends the life of the damper. || Stem with micropolished chrome layer for better slip and reduced wear. Revolutionized multi-lip seal for improved sealing system efficiency. || Manufactured to the same specifications and load values as the original OEM shock absorbers. || Quality Warranty: 4 years against manufacturing defects directly with us. Satisfaction Guarantee, you have 15 days to try them. If you do not have it, we exchange them to you or return your money!
AG Shock Absorber Compatible for Ford F-150 15-18 Front Der
AG Shock Absorber AG Compatible For Ford F-150 2015-2018 Front Right || Pressurized nitrogen gas technology. This compound is best for shock absorbers, as they have a much higher heat tolerance to hydraulics. This allows them to better dampen and also extends the life of the damper. || Stem with micropolished chrome layer for better slip and reduced wear. Revolutionized multi-lip seal for improved sealing system efficiency. || Manufactured to the same specifications and load values as the original OEM shock absorbers. || Quality Warranty: 4 years against manufacturing defects directly with us. Satisfaction Guarantee, you have 15 days to try them. If you do not have it, we exchange them to you or return your money!
AG Shock Absorber AG Compatible For Ford F-150 2015-2018 Front Right || Pressurized nitrogen gas technology. This compound is best for shock absorbers, as they have a much higher heat tolerance to hydraulics. This allows them to better dampen and also extends the life of the damper. || Stem with micropolished chrome layer for better slip and reduced wear. Revolutionized multi-lip seal for improved sealing system efficiency. || Manufactured to the same specifications and load values as the original OEM shock absorbers. || Quality Warranty: 4 years against manufacturing defects directly with us. Satisfaction Guarantee, you have 15 days to try them. If you do not have it, we exchange them to you or return your money!
AG Shock Absorber Compatible for Ford Wolf 15-21 Front Der
AG Shock Absorber AG Compatible For Ford Lobo 2015-2021 Front Right || Pressurized nitrogen gas technology. This compound is best for shock absorbers, as they have a much higher heat tolerance to hydraulics. This allows them to better dampen and also extends the life of the damper. || Stem with micropolished chrome layer for better slip and reduced wear. Revolutionized multi-lip seal for improved sealing system efficiency. || Manufactured to the same specifications and load values as the original OEM shock absorbers. || Quality Warranty: 4 years against manufacturing defects directly with us. Satisfaction Guarantee, you have 15 days to try them. If you do not have it, we exchange them to you or return your money!
AG Shock Absorber AG Compatible For Ford Lobo 2015-2021 Front Right || Pressurized nitrogen gas technology. This compound is best for shock absorbers, as they have a much higher heat tolerance to hydraulics. This allows them to better dampen and also extends the life of the damper. || Stem with micropolished chrome layer for better slip and reduced wear. Revolutionized multi-lip seal for improved sealing system efficiency. || Manufactured to the same specifications and load values as the original OEM shock absorbers. || Quality Warranty: 4 years against manufacturing defects directly with us. Satisfaction Guarantee, you have 15 days to try them. If you do not have it, we exchange them to you or return your money!
Number on catalog scheme:
6
For full view, you need register
Compatible equipment models: 2173031:
Information:
Remove Front Drive Housing
START BY:a. remove oil and water pump driveb. remove accessory drive (front)c. remove fan drived. remove trunnione. remove crankcase breatherf. remove crankshaft front seal and wear sleeve 1. Remove the bolts, and remove cover (1) from the front drive housing. 2. Remove the bolts from plug (2), and use tooling (A) to remove plug (2) from the front drive housing. 3. Remove the bolts from shaft (3). Use tooling (A) to remove shaft (3), the gear and washer from the front drive housing.4. If necessary, remove the bearing from the gear. 5. Fasten a hoist to support (4), and remove the bolts to remove support (4) and base (5) as a unit from the front drive housing. The weight of the unit is 82 kg (180 lb.). 6. Remove fuel control lever (6) from fuel control linkage (7).
Fuel control linkage (7) must be moved for clearance to pull the front drive housing from the engine or damage to parts can be the result.
7. Fasten a hoist to front drive housing (8) with tooling (B). Remove two bolts, and install two 5/8"-11 NC guide bolts. Remove the remainder of the bolts from front drive housing (8), and remove it from the engine. The weight of front drive housing (8) is 209 kg (460 lb.).Install Front Drive Housing
1. Install two 5/8"-11 NC guide bolts in the end of the cylinder block. Fasten a hoist to front drive housing (1) with tooling (A). Put the gasket and front drive housing (1) in position on the guide bolts. Install the bolts to hold the front drive housing in position. Remove the guide bolts, and install the remainder of the bolts. Tighten all of the bolts evenly to their standard torques. Cut the gasket even with the bottom of the cylinder block. 2. Install fuel control lever (2) on the fuel control linkage. 3. Fasten a hoist to support (3), and put support (3) and base (4) as a unit in position on the front drive housing. Install the bolts to hold the unit in position. 4. Use tool group (B) to install the bearing in gear (5) if necessary. The bore in the bearing must be 90.00 0.06 mm (3.543 .002 in.) after assembly.5. Make sure the O-ring seal on shaft (7) has clean engine oil on it. Put washer (6) and gear (5) in position in the front drive housing, and install shaft (7). Install the bolts to hold these in position. 6. Make sure the O-ring seal on plug (8) has clean engine oil on it, and install plug (8) in the front drive housing. Install the bolts to hold the plug in position. 7. Make sure the O-ring seal on cover (9) has clean engine oil on it, and install cover (9) on the front drive housing. Install the bolts to hold the cover in position.END BY:a. install oil and water pump driveb. install accessory drive (front)c. install fan drived. install trunnione. install crankcase
START BY:a. remove oil and water pump driveb. remove accessory drive (front)c. remove fan drived. remove trunnione. remove crankcase breatherf. remove crankshaft front seal and wear sleeve 1. Remove the bolts, and remove cover (1) from the front drive housing. 2. Remove the bolts from plug (2), and use tooling (A) to remove plug (2) from the front drive housing. 3. Remove the bolts from shaft (3). Use tooling (A) to remove shaft (3), the gear and washer from the front drive housing.4. If necessary, remove the bearing from the gear. 5. Fasten a hoist to support (4), and remove the bolts to remove support (4) and base (5) as a unit from the front drive housing. The weight of the unit is 82 kg (180 lb.). 6. Remove fuel control lever (6) from fuel control linkage (7).
Fuel control linkage (7) must be moved for clearance to pull the front drive housing from the engine or damage to parts can be the result.
7. Fasten a hoist to front drive housing (8) with tooling (B). Remove two bolts, and install two 5/8"-11 NC guide bolts. Remove the remainder of the bolts from front drive housing (8), and remove it from the engine. The weight of front drive housing (8) is 209 kg (460 lb.).Install Front Drive Housing
1. Install two 5/8"-11 NC guide bolts in the end of the cylinder block. Fasten a hoist to front drive housing (1) with tooling (A). Put the gasket and front drive housing (1) in position on the guide bolts. Install the bolts to hold the front drive housing in position. Remove the guide bolts, and install the remainder of the bolts. Tighten all of the bolts evenly to their standard torques. Cut the gasket even with the bottom of the cylinder block. 2. Install fuel control lever (2) on the fuel control linkage. 3. Fasten a hoist to support (3), and put support (3) and base (4) as a unit in position on the front drive housing. Install the bolts to hold the unit in position. 4. Use tool group (B) to install the bearing in gear (5) if necessary. The bore in the bearing must be 90.00 0.06 mm (3.543 .002 in.) after assembly.5. Make sure the O-ring seal on shaft (7) has clean engine oil on it. Put washer (6) and gear (5) in position in the front drive housing, and install shaft (7). Install the bolts to hold these in position. 6. Make sure the O-ring seal on plug (8) has clean engine oil on it, and install plug (8) in the front drive housing. Install the bolts to hold the plug in position. 7. Make sure the O-ring seal on cover (9) has clean engine oil on it, and install cover (9) on the front drive housing. Install the bolts to hold the cover in position.END BY:a. install oil and water pump driveb. install accessory drive (front)c. install fan drived. install trunnione. install crankcase
Caterpillar parts catalog:
Parts belt Caterpillar catalog:
120H, 12H, 135H, 2290, 2390, 2391, 2491, 2590, 3126B, 322C, 322C FM, 325C, 325C FM, 325D L, 329D L, 330C, 330C FM, 330C L, 330C MH, 330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D...
9X8139
BELT-DRIVE
120G, 120H, 120H ES, 120H NA, 120M, 12G, 12H, 12H ES, 12H NA, 12M, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140M, 143H, 14H, 14H NA, 14M, 160G, 160H, 160H ES, 160H NA, 160M, 163H, 163H NA, 1...
120G, 120H, 120H ES, 120H NA, 120M, 12G, 12H, 12H ES, 12H NA, 12M, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140M, 143H, 14H, 14H NA, 14M, 160G, 160H, 160H ES, 160H NA, 160M, 163H, 163H NA, 1...
938G II, 950G II, 962G II, C7, CP-56, CP-64, CP-76, CS-56, CS-64, CS-74, D5K2 XL, IT38G II, IT62G II
950H, 962H, 966G II, 972G II, C15, D5R LGP, D6N, IT62H
938G II, 950H, 962H, D5N, D6N, IT38G II, IT62H
938G II, 950G II, 962G II, IT38G II, IT62G II
950H, 962H, IT62H
950H, 966G II, 972G II
2143015
BELT
950H
950H
349E, 349E L, 349E L HVG, 349E L VG, 349F L, 621B, 621G, 623G, 627F, 627G, 631D, 631E, 633E II, 637D, 637E, TK1051
3215168
BELT-SERPENTINE
631D, 631E, 631G, 633E II, 637D, 637E, 637G
631D, 631E, 631G, 633E II, 637D, 637E, 637G
3812510
BELT TENSIONER
621G, 623G, 627G, 631E, 631G, 633E II, 637E, 637G, 657E, 657G
621G, 623G, 627G, 631E, 631G, 633E II, 637E, 637G, 657E, 657G
621, 621B, 621E, 623E, 627B, 627E, 631E, 637D, 637E, 641B, 651E, 657E
924H, 924HZ, 928H, 928HZ
938G II, 950G II, 962G II, IT38G II, IT62G II
3110330
BELT TENSIONER
657E, 657G
657E, 657G
3300661
BELT-SERPENTINE
657E, 657G
657E, 657G
3812512
BELT TENSIONER
627G, 637D, 637E, 637G
627G, 637D, 637E, 637G
3812509
BELT TENSIONER
627G, 637D, 637E, 637G
627G, 637D, 637E, 637G
627G, 637D, 637E, 637G
627G, 637D, 637E, 637G