2985873 BELT Caterpillar parts
C7.1
Rating:
Alternative (cross code) number:
CA2985873
298-5873
2985873
CA2985873
298-5873
2985873
Weight: 0.47 pounds 0 kg.
INDUSTRIAL ENGINE,
You can buy:
US$35.50
28 May 2025
FridayParts
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
YIHETOP Drive Belt 298-5873 2985873 Compatible for Caterpillar C7.1 Engine 318D2 320D2 313D2 GC Excavator
YIHETOP Part Number:298-5873, 2985873, CA2985873 || Compatible For Caterpillar Excavator:318D2, 318D2 L, 320 GX, 320D2 GC, 323 GX || Compatible For Caterpillar Engine:C7.1
YIHETOP Part Number:298-5873, 2985873, CA2985873 || Compatible For Caterpillar Excavator:318D2, 318D2 L, 320 GX, 320D2 GC, 323 GX || Compatible For Caterpillar Engine:C7.1
Compatible equipment models: 2985873:
Information:
Removal Procedure
Table 1
Required Tools    
Tool    Part Number    Part Description    Qty    
A (1)     221-9778     Puller Stud     1    
128-7889 Bridge Puller     1    
9U-6877 Thrust Bearing     1    
5P-8247 Hard Washer     1    
4K-0367 Nut     1    
( 1 ) The tools that are listed in the chart are part of the 9U-6891 Injector Tool Group .Start By:
Remove the electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit Injector - Remove".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01002969
Illustration 2 g01002972
Install the puller stud from Tooling (A) into unit injector sleeve (1) .
Install the following parts from Tooling (A) over the stud: bridge puller, thrust bearing, hard washer and nut. See Step 1.
Tighten the nut until unit injector sleeve (1) is pulled free of the cylinder head assembly.
Remove Tooling (A) from the unit injector sleeve.
Repeat Steps 1 through 4 in order to remove the remaining unit injector sleeves.
Table 1
Required Tools    
Tool    Part Number    Part Description    Qty    
A (1)     221-9778     Puller Stud     1    
128-7889 Bridge Puller     1    
9U-6877 Thrust Bearing     1    
5P-8247 Hard Washer     1    
4K-0367 Nut     1    
( 1 ) The tools that are listed in the chart are part of the 9U-6891 Injector Tool Group .Start By:
Remove the electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit Injector - Remove".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01002969
Illustration 2 g01002972
Install the puller stud from Tooling (A) into unit injector sleeve (1) .
Install the following parts from Tooling (A) over the stud: bridge puller, thrust bearing, hard washer and nut. See Step 1.
Tighten the nut until unit injector sleeve (1) is pulled free of the cylinder head assembly.
Remove Tooling (A) from the unit injector sleeve.
Repeat Steps 1 through 4 in order to remove the remaining unit injector sleeves.
Caterpillar parts catalog:
Parts belt Caterpillar catalog:
3754479
BELT TENSIONER GP
525D, 535D, 545D, 950 GC, C7.1, D6K2
525D, 535D, 545D, 950 GC, C7.1, D6K2
3779082
BELT TENSIONER
312D2, 312D2 GC, 312D2 L, 313D2, 313D2 LGP, 318D2 L, 416E, 416F, 420E, 420F, 422E, 422F, 428E, 428F, 430E, 430F, 432E, 432F, 434E, 434F, 442E, 444E, 444F, 450E, 450F, 559, 924K, 930K, 938K, AP-300D, A...
312D2, 312D2 GC, 312D2 L, 313D2, 313D2 LGP, 318D2 L, 416E, 416F, 420E, 420F, 422E, 422F, 428E, 428F, 430E, 430F, 432E, 432F, 434E, 434F, 442E, 444E, 444F, 450E, 450F, 559, 924K, 930K, 938K, AP-300D, A...
2831171
BELT-SERPENTINE
450E, C4.4, C6.6, C7.1
450E, C4.4, C6.6, C7.1
3652985
BELT-SERPENTINE
C4.4, C7.1, CB-44B, CB-54B, CP-54B, CP-68B, CP-74B, CS-54B, CS-56B, CS-64B, CS-66B, CS-76B, CS-78B, CW-34
C4.4, C7.1, CB-44B, CB-54B, CP-54B, CP-68B, CP-74B, CS-54B, CS-56B, CS-64B, CS-66B, CS-76B, CS-78B, CW-34
3096668
BELT
C7.1
C7.1
3828827
BELT
C7.1
C7.1
3160446
BELT-SERPENTINE
C4.4, D4K XL, D5K LGP
C4.4, D4K XL, D5K LGP
3L6052
BELT
D353C
D353C
2L8591
BELT
D353C
D353C
2L9492
BELT
D353C
D353C
3L1382
BELT
D342
D342
6B8536
BELT
D342
D342
4M9678
BELT
955H, D346
955H, D346