3826244 BELT-DRIVE Caterpillar parts
HM415B
Rating:
Alternative (cross code) number:
CA3826244
382-6244
3826244
CA3826244
382-6244
3826244
Weight: 1 pounds 0 kg.
MULCHING HEAD,
This part in 5 request:
Show.
This information for suppliers only!
2024-12-05
2024-10-16
2022-02-18
2021-08-18
2020-11-04
Compatible equipment models: 3826244:
Number on catalog scheme:
7
For full view, you need register
Information:
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 175-5507 Nitrogen Charging Group 1
B 1P-2853 Spanner Wrench 1 Start By:
Remove the steering accumulator. Refer to Disassembly and Assembly, "Steering Accumulator - Remove".Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the component should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism.Note: The accumulator contains nitrogen gas that is under high pressure. Do not attempt to disassemble the accumulator until the pressure has been released.
Personal injury can result from the sudden release of high pressure oil.Be sure the engine has been shut off for a minimum of five minutes to ensure that the accumulator pressure is zero.The accumulator is filled with dry nitrogen. Do not loosen or remove the valve or the cap from the top of the accumulator.
Before the disassembly procedure, use Tooling (A) in order to verify that accumulator (1) is completely discharged.
Illustration 1 g01183788
Remove plug (2) .
Use Tooling (B) in order to remove nut (3). Remove spacer (4) .
Illustration 2 g01183805
Push fitting (5) into accumulator shell (6) .
Illustration 3 g01183808
Remove washer (7). Remove O-ring seal (8). Remove ring (9) ..
Illustration 4 g01183810
Fold ring (10) in half in order to remove ring (10) from accumulator shell (6) .
Illustration 5 g01183811
Remove fitting (5) from accumulator shell (6) .
Illustration 6 g01183817
Personal injury can result from being struck by parts propelled by a released spring force.Make sure to wear all necessary protective equipment.Follow the recommended procedure and use all recommended tooling to release the spring force.
Remove nut (11). Remove sleeve (12). Remove spring (13). Remove poppet (14) from fitting (5) .
Illustration 7 g01183823
Remove nut (15).
Remove seal (16) .
Remove valve assembly (17) .
Remove nut (18) .
Illustration 8 g01183832
Remove bladder (19) from accumulator shell (6) .
Table 1
Required Tools
Tool Part Number Part Description Qty
A 175-5507 Nitrogen Charging Group 1
B 1P-2853 Spanner Wrench 1 Start By:
Remove the steering accumulator. Refer to Disassembly and Assembly, "Steering Accumulator - Remove".Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the component should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism.Note: The accumulator contains nitrogen gas that is under high pressure. Do not attempt to disassemble the accumulator until the pressure has been released.
Personal injury can result from the sudden release of high pressure oil.Be sure the engine has been shut off for a minimum of five minutes to ensure that the accumulator pressure is zero.The accumulator is filled with dry nitrogen. Do not loosen or remove the valve or the cap from the top of the accumulator.
Before the disassembly procedure, use Tooling (A) in order to verify that accumulator (1) is completely discharged.
Illustration 1 g01183788
Remove plug (2) .
Use Tooling (B) in order to remove nut (3). Remove spacer (4) .
Illustration 2 g01183805
Push fitting (5) into accumulator shell (6) .
Illustration 3 g01183808
Remove washer (7). Remove O-ring seal (8). Remove ring (9) ..
Illustration 4 g01183810
Fold ring (10) in half in order to remove ring (10) from accumulator shell (6) .
Illustration 5 g01183811
Remove fitting (5) from accumulator shell (6) .
Illustration 6 g01183817
Personal injury can result from being struck by parts propelled by a released spring force.Make sure to wear all necessary protective equipment.Follow the recommended procedure and use all recommended tooling to release the spring force.
Remove nut (11). Remove sleeve (12). Remove spring (13). Remove poppet (14) from fitting (5) .
Illustration 7 g01183823
Remove nut (15).
Remove seal (16) .
Remove valve assembly (17) .
Remove nut (18) .
Illustration 8 g01183832
Remove bladder (19) from accumulator shell (6) .
Caterpillar parts catalog:
Parts belt Caterpillar catalog:
349E, 349E L, 349E L HVG, 349E L VG, 349F L
349E, 349E L, 349E L HVG, 349E L VG, 349F L
3994026
BELT
HM825, MD-250
HM825, MD-250
3300706
BELT-SERPENTINE
120M 2
120M 2
12M 2, 12M 3, 12M 3 AWD, 140M 2, 140M 3, 140M 3 AWD, 160M 2, 160M 3, 160M 3 AWD
120K, 120K 2, 12K, 140K, 140K 2, 160K
330 L, 330B L, E300, W330B
1098613
BELT
350, 350 L
350, 350 L
345B, 345B II, 345B L
2M4049
BELT
12E
12E
9D8386
BELT
12G, 16G
12G, 16G
9D5457
BELT
12G, 16G
12G, 16G