3L6052 BELT Caterpillar parts
D353C
Rating:
Alternative (cross code) number:
CA3L6052
3L-6052
3L6052
CA3L6052
3L-6052
3L6052
Weight: 2 pounds 0 kg.
INDUSTRIAL ENGINE,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
CTP 3L6052 External Engine V-Belt
CTP For External Engine || Highly Efficient || Easy in-and-out fit
CTP For External Engine || Highly Efficient || Easy in-and-out fit
CTP 3L6052 External Engine V-Belt
CTP For External Engine || Highly Efficient || Easy in-and-out fit
CTP For External Engine || Highly Efficient || Easy in-and-out fit
This part in 2 request:
Show.
This information for suppliers only!
2019-12-30
2018-03-26
Number on catalog scheme:
None
For full view, you need register
Compatible equipment models: 3L6052:
Information:
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
B 1P-0510 Driver Group 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01252599
Illustration 2 g01252424
Ensure that the oil hole in the bearing is aligned with the oil passage in housing (15). Use Tooling (B) and a suitable press to install bearing (14) in housing (15). Bearing (14) must be 1.5 0.5 mm (0.06 0.02 inch) below the surface of the housing. The diameter of bearing (14) must be 75.000 0.055 mm (2.9527 0.0022 inch) after installation.
Illustration 3 g01252620
Use Tooling (B) to install lip seal (13) in housing (15). Ensure that the lip of the seal is toward the bearing. Place clean engine oil on the lip seal.
Illustration 4 g01252420
Install shaft (7), retaining washers (12), the shims, and the bolts that hold shaft (7) in the housing.
Illustration 5 g01252622
Place clean engine oil on the bearing in the housing. Install shaft (1) and retaining washers (11) on shaft (7). Install retaining washers (11) and the bolts on the housing.
Clean water is the only lubricant that is permitted for assembly. DO NOT damage or touch the wear surfaces of the carbon ring or the ceramic ring. Install the ceramic ring with the smoothest face of the ring toward the carbon seal.
Illustration 6 g01252650
Install ceramic seal (10) in the rubber ring. Place clean water on the rubber ring and ceramic seal (10) for lubrication. Use hand pressure and the Tooling that is supplied with the seal group to install the ceramic seal.
Illustration 7 g01252659
Remove the spring from carbon seal assembly (9). Place clean water on the inside diameter of the carbon seal assembly for lubrication. Use hand pressure and the Tooling that is supplied with the seal group in order to install carbon seal assembly (9). The face of the seal should make light contact with the shaft.
Illustration 8 g01252660
Improper assembly of parts that are spring loaded can cause bodily injury.To prevent possible injury, follow the established assembly procedure and wear protective equipment.
Install spring (8) on carbon seal assembly (9).
Illustration 9 g01252664
Place clean engine oil on the shaft prior to installation of impeller (6). Install impeller (6) on the shaft. Use a suitable press to install impeller (6). Install the impeller until the distance between the face of the impeller and the face of the shaft is 0.000 0.076 mm (0.0000 0.0030 inch).
Illustration 10 g00592355
Install the O-ring seal around adapter (5). Place clean engine oil on the O-ring seal.
Position adapter (5) on the housing and install the bolts.
Illustration 11 g00592354
Place gear (2) on shaft (1) and install the bolts.
Install O-ring seals (3) and (4) on the housing. Place clean engine oil on the O-ring seals. End By:
Install the auxiliary water pump. Refer to Disassembly and Assembly, "Auxiliary Water Pump - Install".
Table 1
Required Tools
Tool Part Number Part Description Qty
B 1P-0510 Driver Group 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01252599
Illustration 2 g01252424
Ensure that the oil hole in the bearing is aligned with the oil passage in housing (15). Use Tooling (B) and a suitable press to install bearing (14) in housing (15). Bearing (14) must be 1.5 0.5 mm (0.06 0.02 inch) below the surface of the housing. The diameter of bearing (14) must be 75.000 0.055 mm (2.9527 0.0022 inch) after installation.
Illustration 3 g01252620
Use Tooling (B) to install lip seal (13) in housing (15). Ensure that the lip of the seal is toward the bearing. Place clean engine oil on the lip seal.
Illustration 4 g01252420
Install shaft (7), retaining washers (12), the shims, and the bolts that hold shaft (7) in the housing.
Illustration 5 g01252622
Place clean engine oil on the bearing in the housing. Install shaft (1) and retaining washers (11) on shaft (7). Install retaining washers (11) and the bolts on the housing.
Clean water is the only lubricant that is permitted for assembly. DO NOT damage or touch the wear surfaces of the carbon ring or the ceramic ring. Install the ceramic ring with the smoothest face of the ring toward the carbon seal.
Illustration 6 g01252650
Install ceramic seal (10) in the rubber ring. Place clean water on the rubber ring and ceramic seal (10) for lubrication. Use hand pressure and the Tooling that is supplied with the seal group to install the ceramic seal.
Illustration 7 g01252659
Remove the spring from carbon seal assembly (9). Place clean water on the inside diameter of the carbon seal assembly for lubrication. Use hand pressure and the Tooling that is supplied with the seal group in order to install carbon seal assembly (9). The face of the seal should make light contact with the shaft.
Illustration 8 g01252660
Improper assembly of parts that are spring loaded can cause bodily injury.To prevent possible injury, follow the established assembly procedure and wear protective equipment.
Install spring (8) on carbon seal assembly (9).
Illustration 9 g01252664
Place clean engine oil on the shaft prior to installation of impeller (6). Install impeller (6) on the shaft. Use a suitable press to install impeller (6). Install the impeller until the distance between the face of the impeller and the face of the shaft is 0.000 0.076 mm (0.0000 0.0030 inch).
Illustration 10 g00592355
Install the O-ring seal around adapter (5). Place clean engine oil on the O-ring seal.
Position adapter (5) on the housing and install the bolts.
Illustration 11 g00592354
Place gear (2) on shaft (1) and install the bolts.
Install O-ring seals (3) and (4) on the housing. Place clean engine oil on the O-ring seals. End By:
Install the auxiliary water pump. Refer to Disassembly and Assembly, "Auxiliary Water Pump - Install".
Caterpillar parts catalog:
Parts belt Caterpillar catalog:
2L9492
BELT
D353C
D353C
D353C
D353C
D353C
2L9492
BELT
D353C
D353C
D342
6B8536
BELT
D342
D342
4M9678
BELT
955H, D346
955H, D346
C7.1
824, D320A
D320A
D342C
D342C
D342C
D353C