1534089 BIT GP-AUGER Caterpillar parts
A13, A19, A26B, A7B
Rating:
Alternative (cross code) number:
CA1534089
153-4089
1534089
CA1534089
153-4089
1534089
Weight: 337 pounds 152 kg.
AUGER,
Information:
The orifice tube may be located in the refrigerant line near the evaporator inlet, or in the in-line dryer.If the orifice tube is located in the refrigerant line near the evaporator inlet, use the procedure that follows. If the orifice tube is located in the in-line dryer, refer to Dryer Replacement.Removing the Orifice Tube
Refer to Safety Requirements before service work is performed on the air conditioning system.The refrigerant must be recovered before removing the accumulator. Refer to the Testing and Adjusting, "Refrigerant Recovery" section.
Do not attempt to remove the orifice tube with pliers. Do not twist or rotate the orifice tube in the tube assembly.
Illustration 1 g00379603
Orifice tube (1) O-Ring seals (2) Lugs (3) Body (4) Drive screw (5) Finger lock
Disconnect the high side line at the enlarged section of the evaporator inlet port. This will expose the orifice tube for removal.
Align the short fingers of the 1U-9890 Orifice Removal Tool with the ribs of the orifice tube. Insert the tool onto the tube until the tool bottoms out.
Turn drive screw (4) clockwise. Turn far enough to engage the lugs (2) on the orifice tube in the finger lock (5) . The finger lock (5) is part of the removal tool.
Hold the drive screw (4) stationary. Thread the body (3) forward until the body makes contact with the inlet port.
Continue holding the drive screw stationary, and thread the body forward until the orifice tube becomes free.
Illustration 2 g00381412
Removing the broken orifice tube (3) Body (4) Drive screw (6) Extractor tip
For the removal of the orifice tube assembly, use the extractor tip (6) on 1U-9890 Orifice Removal Tool . Insert the tool into the evaporator inlet tube and thread the tool into the brass center of the orifice tube.
Repeat steps 3 and 4.
If only the brass center of the orifice tube is removed, thread the tool into the plastic body and repeat step 3 and 4.Orifice Tube Installation
Lubricate the O-Ring on the orifice tube with the proper clean refrigerant oil.
Place the orifice tube into the 1U-9890 Orifice Removal Tool . Insert the orifice tube straight into the evaporator inlet tube without twisting until the tube is seated.
Disengage the removal tool from the orifice tube.
Use a new O-Ring that is lubricated with clean refrigerant oil. Reconnect the high side line at the enlarged section of the evaporator inlet port.
Do a leak test. Evacuate the system and recharge the system. Refer to the Testing and Adjusting, "Refrigerant Systems-Evacuate" section. Also, refer to the Testing and Adjusting, "Refrigerant Systems-Charge" section.
Caterpillar SIS machinery equipment:
Caterpillar SIS
303.5E CR Mini Hydraulic Excavator JX200001-UP (MACHINE) POWERED BY C1.8 Engine »
153-4089
BIT GP-AUGER
A13 Auger ACY00001-UP (MACHINE) »
153-4089
BIT GP-AUGER
A19 Auger ADA00001-UP (MACHINE) »
153-4089
BIT GP-AUGER
A19B & A26B Augers LLS00001-UP (MACHINE) »
153-4089
BIT GP-AUGER
A7B & A14B Augers JMT00001-UP (MACHINE) »
153-4089
BIT GP-AUGER
305E2 CR Mini Hydraulic Excavator DJX00001-UP (MACHINE) POWERED BY C2.4 Engine »
153-4089
BIT GP-AUGER
303.5E 2CR Mini Hydraulic Excavator BG800001-UP (MACHINE) POWERED BY C1.7 Engine »
153-4089
BIT GP-AUGER
305.5E2 CR Mini Hydraulic Excavator EJX00001-UP (MACHINE) POWERED BY C2.4 Engine »
153-4089
BIT GP-AUGER
307E2 Mini Hydraulic Excavator KC900001-UP (MACHINE) POWERED BY C2.4 Engine »
153-4089
BIT GP-AUGER
Parts bit Caterpillar catalog:
3667752
BIT GP-AUGER
308E2 CR, A26B, A7B
308E2 CR, A26B, A7B
1534085
BIT GP-AUGER
A13, A19, A26, A26B, A7, A7B
A13, A19, A26, A26B, A7, A7B
1534091
BIT GP-AUGER
A19, A26B
A19, A26B
1534095
BIT GP-AUGER
A19, A26B
A19, A26B
2173194
BIT GP-AUGER
A19, A26
A19, A26
3720261
BIT GP-AUGER
A26B, A7B
A26B, A7B
1566331
BIT AS
A13, A19, A26, A26B, A7, A7B
A13, A19, A26, A26B, A7, A7B
1566332
BIT AS
A13, A19, A26, A26B, A7, A7B
A13, A19, A26, A26B, A7, A7B
1566333
BIT AS
A13, A19, A26, A26B, A7, A7B
A13, A19, A26, A26B, A7, A7B
1566334
BIT AS-AUGER
A13, A19, A26B, A7B
A13, A19, A26B, A7B
1566336
BIT AS-AUGER
A13, A19, A26B, A7B
A13, A19, A26B, A7B
2173193
BIT AS
A19, A26
A19, A26
1534086
BIT GP-AUGER
A13, A19, A26, A26B, A7, A7B
A13, A19, A26, A26B, A7, A7B
1534085
BIT GP-AUGER
A13, A19, A26, A26B, A7, A7B
A13, A19, A26, A26B, A7, A7B
1534084
BIT GP-AUGER
A13, A19, A26, A26B, A7, A7B
A13, A19, A26, A26B, A7, A7B
1534083
BIT GP-AUGER
305.5E, A13, A19, A26, A26B, A7, A7B
305.5E, A13, A19, A26, A26B, A7, A7B
3234280
BIT-END
527
527
3234279
BIT-END
527
527
3359033
BIT-END
D7R II
D7R II
3359032
BIT-END
D7R II
D7R II
2173194
BIT GP-AUGER
A19, A26
A19, A26
1534095
BIT GP-AUGER
A19, A26B
A19, A26B
1534091
BIT GP-AUGER
A19, A26B
A19, A26B
1534092
BIT GP-AUGER
A13, A19, A26B, A7B
A13, A19, A26B, A7B