8E4197 BIT-END Caterpillar parts
844, 844H, 844K, D8L, D9N, D9R, D9T
Rating:
Alternative (cross code) number:
CA8E4197
8E-4197
8E4197
CA8E4197
8E-4197
8E4197
Weight: 115 pounds 52 kg.
TRACK-TYPE TRACTOR, WHEEL DOZER,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
8E4197 BIT-END RH (New AFTERMARKET) - G&T Engine Parts
G&T Engine Parts Fits equipment: ENGINE - MACHINE: 3408, 3408C, 3408E, 3412D, 3412E, C18, C27; TRACK-TYPE TRACTOR: D9R, D9T; WHEEL DOZER: 844, 844K, 844H; WORK TOOL: !, 834G, 836G. || Condition: NEW AFTERMARKET || Weight: 126.5 lbs || Dimensions: 10-10-10.38 in || Use of any OEM manufacturer name is not intended to represent any relationship between the two companies, instead it indicates that we sell replacement parts that are compatible with OEM components.
G&T Engine Parts Fits equipment: ENGINE - MACHINE: 3408, 3408C, 3408E, 3412D, 3412E, C18, C27; TRACK-TYPE TRACTOR: D9R, D9T; WHEEL DOZER: 844, 844K, 844H; WORK TOOL: !, 834G, 836G. || Condition: NEW AFTERMARKET || Weight: 126.5 lbs || Dimensions: 10-10-10.38 in || Use of any OEM manufacturer name is not intended to represent any relationship between the two companies, instead it indicates that we sell replacement parts that are compatible with OEM components.
End Bit - Hot Cupped fits Caterpillar 8E4197
National 1 Track & Parts We use precision manufacturing to deliver the highest quality parts
National 1 Track & Parts We use precision manufacturing to deliver the highest quality parts
Number on catalog scheme:
11
For full view, you need register
Compatible equipment models: 8E4197:
Information:
Use this procedure in order to troubleshoot a problem with the fuel filters. Or, use this procedure if any of the following event codes are active.
Table 1
Event Codes
J1939 Code and Description Conditions which Generate this Code System Response
95-15 Engine Fuel Filter Differential Pressure : High - least severe (1) The difference between the filtered fuel pressure and the unfiltered fuel pressure is greater than the trip point pressure. The code is logged.
The ECM may derate the engine or shutdown the engine. Probable Causes
Fuel filter element
Electrical problemRecommended Actions
Note: The procedures have been listed in order of probability. Complete the procedures in the order of the listed test steps.
Table 2
Troubleshooting Test Step Value Result
1. Active Codes and Logged Codes
A. Establish communication between Caterpillar Electronic Technician (ET) and the Electronic Control Module (ECM).
B. Monitor the diagnostic codes on Cat ET. Check for active or logged diagnostic codes. Specifically check for codes that could be associated to a restricted fuel supply.
Note: Wait at least 30 seconds in order for diagnostic codes to become active.
Engine Logged or Active Codes Result: A diagnostic code is present.
Repair: Troubleshoot any codes before continuing with this procedure.
Verify that the repair eliminated the problem.
Result: The problem has not been resolved.
Proceed to Test Step 2.
2. Fuel Filter Element
A. Replace the appropriate fuel filter elements for the code.
B. Prime the fuel system. Refer to the Operation and Maintenance Manual for information.
C. Restart the engine and check for an active event code for the filter that was changed.
Filter
Result: After starting the engine, the event code is no longer active for the filter that was changed.
STOP
Result: After starting the engine, the event code remained active for the filter that was changed
Proceed to Test Step 3
3. Electrical Problem
A. Inspect the sensor, wiring, and connectors for damage and corrosion. Refer to Troubleshooting, "Electrical Connectors - Inspect" for information that is related to intermittent electrical problems.
B. Determine if an associated code is present for a pressure sensor that is related the filter.
Electrical codes
Result: A circuit component is damaged or corroded.
Repair: Repair or replace the circuit component.
Verify that the repair eliminated the problem.
Result: There is a fault code for a sensor that is related to the filter.
Refer to Troubleshooting, "Sensor Signal (Analog, Active) - Test"
If the procedure did not correct the issue, contact your Cat dealer Technical Communicator (TC). For further assistance, your TC can confer with the Dealer Solutions Network (DSN).
Table 1
Event Codes
J1939 Code and Description Conditions which Generate this Code System Response
95-15 Engine Fuel Filter Differential Pressure : High - least severe (1) The difference between the filtered fuel pressure and the unfiltered fuel pressure is greater than the trip point pressure. The code is logged.
The ECM may derate the engine or shutdown the engine. Probable Causes
Fuel filter element
Electrical problemRecommended Actions
Note: The procedures have been listed in order of probability. Complete the procedures in the order of the listed test steps.
Table 2
Troubleshooting Test Step Value Result
1. Active Codes and Logged Codes
A. Establish communication between Caterpillar Electronic Technician (ET) and the Electronic Control Module (ECM).
B. Monitor the diagnostic codes on Cat ET. Check for active or logged diagnostic codes. Specifically check for codes that could be associated to a restricted fuel supply.
Note: Wait at least 30 seconds in order for diagnostic codes to become active.
Engine Logged or Active Codes Result: A diagnostic code is present.
Repair: Troubleshoot any codes before continuing with this procedure.
Verify that the repair eliminated the problem.
Result: The problem has not been resolved.
Proceed to Test Step 2.
2. Fuel Filter Element
A. Replace the appropriate fuel filter elements for the code.
B. Prime the fuel system. Refer to the Operation and Maintenance Manual for information.
C. Restart the engine and check for an active event code for the filter that was changed.
Filter
Result: After starting the engine, the event code is no longer active for the filter that was changed.
STOP
Result: After starting the engine, the event code remained active for the filter that was changed
Proceed to Test Step 3
3. Electrical Problem
A. Inspect the sensor, wiring, and connectors for damage and corrosion. Refer to Troubleshooting, "Electrical Connectors - Inspect" for information that is related to intermittent electrical problems.
B. Determine if an associated code is present for a pressure sensor that is related the filter.
Electrical codes
Result: A circuit component is damaged or corroded.
Repair: Repair or replace the circuit component.
Verify that the repair eliminated the problem.
Result: There is a fault code for a sensor that is related to the filter.
Refer to Troubleshooting, "Sensor Signal (Analog, Active) - Test"
If the procedure did not correct the issue, contact your Cat dealer Technical Communicator (TC). For further assistance, your TC can confer with the Dealer Solutions Network (DSN).
Cat SIS web machinery list:
Parts bit Caterpillar catalog:
8A, D8L
834G, 834H, 834K, D8N, D8R, D8R II, D9N, D9R
834G, 834H, 834K, D8N, D8R, D8R II, D9N, D9R
844, 844H, 844K, D8L, D9N, D9R, D9T
824H, 824K, 826H, 826K, D9R
824H, 824K, 826H, 826K, D9R
D8L, D9N, D9R, D9T
D8L, D9N, D9R, D9T
844, 844H, 844K, D8L, D9N, D9R, D9T
120H NA, 12H NA, 135H NA, 140H NA, 140M, 143H, 14M, 160H NA, 160M, 163H NA, SNOW WING
120H NA, 12H NA, 135H NA, 140H NA, 140M, 143H, 14M, 160H NA, 160M, 163H NA, SNOW WING
2675451
BIT-END
963C, 963D
963C, 963D
5G8268
BIT
933C, 939C, 943
933C, 939C, 943
1774552
BIT-END
D6M, D6N
D6M, D6N
825G, 826C, 826G, 826G II, 826H, 826K, 834G, 836, 836G, 836H, 836K, D7E, D7E LGP, D7H, D7R, D7R II
825G, 826C, 826G, 826G II, 826H, 826K, 834G, 836, 836G, 836H, 836K, D7E, D7E LGP, D7H, D7R, D7R II
3937859
BIT-END
824H, 824K
824H, 824K
824H, 824K
834H, 834K, D8N, D8R, D8R II, D8T
834H, 834K, D8N, D8R, D8R II, D8T