AVSPARE.COM
parts catalog

BLADE & EDGE GP-ANGLING 3967385 - Caterpillar



3967385 BLADE & EDGE GP-ANGLING Caterpillar parts D6T LGPPAT BLADE
Rating:
8
Alternative (cross code) number:
CA3967385
396-7385
3967385
Caterpillar 3967385 BLADE & EDGE GP-ANGLING

Buy BLADE & EDGE GP-ANGLING 3967385 Caterpillar genuine, new aftermarket tractor parts with delivery
TRACK-TYPE TRACTOR,

Compatible equipment models: 3967385:

TRACK-TYPE TRACTOR  D6T LGPPAT   Caterpillar
  For full view, you need register

Information:

Payload Weight Measurement
Payload weight measurement is a function of the suspension cylinder pressure sensors. Certain conditions could affect the accuracy of the Truck Payload Measurement System (TPMS) when the truck is loaded. Some of these conditions are listed as follow:
A truck is loaded on a sloped surface that is greater than 5%. Accuracy will become progressively worse as the slope becomes greater.Note: Refer to System Operation, "Payload Management Guidelines" for proper loading guidelines.
A suspension cylinder is not properly charged. The suspension cylinders may not cause an event even if the charge is incorrect. However, the weighing accuracy will be affected.Reference: See Special Instruction, SEHS9411, "Servicing the Suspension Cylinders for Off-Highway Trucks" for information on servicing the suspension cylinders.
Pushing down on the load with the loading tool during the loading process (packing the load).
Actuating the body raise lever during loading.
A failure to perform payload calibration after replacing components in the TPMS.
A failure to perform payload calibration after any substantial changes to the empty weight of the truck. Refueling does not require payload calibration.
Using a conveyor or a continuous feed system for loading.
Failures in the TPMS may cause the payload weight to become inaccurate. Diagnostic events will be shown in the "event list".
The incorrect VIMS 3G onboard software is installed.
The load is placed in the body, too far from the center of the marker.
The payload configuration is set incorrectly.Note: The accuracy of the TPMS is not affected if the first load is placed into the truck before the truck has stopped completely. The truck can also be repositioned during loading. If the accuracy of the payload measurement is suspect, confirm the list of items that follow:
The VIMS ECM have the correct software and the most recent revision.
No service work has been performed on the payload system that may have created the reported diagnostic.
The Payload system is configured correctly for the model of the truck. Refer to Testing and Adjusting, "Payload System - Configure".
The payload system has been calibrated. Refer to Testing and Adjusting, "Payload System - Calibrate".
The suspension cylinders are not topping out or bottoming out due to an incorrect charge pressure. Refer to Special Instruction, SEHS9411, "Servicing the Suspension Cylinders for Off-Highway Trucks"Payload Reweigh
The accuracy of the reweigh process will be affected if the haul road is in need of repair.


Parts blade Caterpillar catalog:

6V5849 BLADE AS-WIPER
120H, 120H ES, 120H NA, 120M, 120M 2, 12H, 12H ES, 12H NA, 12M, 135H, 135H NA, 140H, 140H ES, 140H NA, 140K, 140M, 140M 2, 143H, 14H, 14H NA, 160H, 160H ES, 160H NA, 160M, 160M 2, 163H, 163H NA, 16H, ...
1258175 BLADE AS-WIPER
65C, 75C, 75D, 85C, 85D, 953C, 963C, 973C, D3G, D3K XL, D3K2 LGP, D4G, D4K XL, D4K2 XL, D5G, D5K LGP, D5K2 XL, D5N, D5R LGP, D6K, D6K LGP, D6K XL, D6K2, D6K2 LGP, D6N, D6N LGP, D6R, D6R II, D6R III, D...
1285040 BLADE AS-WIPER
322B L, 325B L, 330B L, 345B, 345B II, 345B II MH, 345B L, 350, 375 L, 385B, 5080, D10T, D10T2, D11T, D6T LGP, D6T LGPPAT, D8T, D9T, DEUCE, M325B, R1300G, R1300G II, R1600, R1600G, R1600H, R1700G, W33...
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.