4214312 BLADE GP-UNIVERSAL Caterpillar parts
D6T XL
Rating:
Alternative (cross code) number:
CA4214312
421-4312
4214312
CA4214312
421-4312
4214312
TRACK-TYPE TRACTOR,
Compatible equipment models: 4214312:
Information:
Which Generate This Code:The Electronic Control Module (ECM) detects the following condition:
Exhaust inlet temperature is greater than the default temperature of 750 °C (1382 °F) for five seconds.
The engine has been running for three seconds.
The diagnostic codes CID-FMI 827-08 and CID-FMI 828-08 are not active.System Response:The ECM will log the event. The ECM derates the engine at 15 second intervals in 2 percent increments when the exhaust inlet temperature is above 750 °C (1382 °F) for five seconds up to a maximum derate of 25 percent. The Fuel limiting function will continue until the exhaust temperature returns below 740 °C (1364 °F). After the temperature returns below 740 °C (1364 °F) the derate due to a high exhaust temperature will be deactivated.
Low power
There may be an exhaust restriction.
There may be an air leak.Test Step 1. Check for "ACTIVE" Diagnostic Codes
Start the Caterpillar Electronic Technician (ET).
Turn the keyswitch to the ON position.
Check for any active diagnostic codes or logged diagnostic codes.Expected Result:There are no diagnostic codes that are present.Results:
OK - There are no diagnostic codes that are present. Proceed to Test Step 2.
Not OK - There are diagnostic codes that are present.Repair: Repair the diagnostic codes that are present. Refer to the appropriate topic in the "Troubleshooting With a Diagnostic Code" section of this manual. Ensure that the repair eliminates the problem.STOPTest Step 2. Perform a Check of the Exhaust System
Perform a check of the exhaust system. Refer to the diagnostic procedure Troubleshooting, "Exhaust Temperature is Too High" for possible causes.Expected Result:There are no problems with the exhaust system.Results:
OK - There may be an intermittent problem.Repair: Monitor the operation of the engine. Repair the problem. Ensure that the repair eliminates the problem.STOP
Not OK - There is a problem with the exhaust system.Repair: Repair the problem. Ensure that the repair eliminates the problem.STOP
Exhaust inlet temperature is greater than the default temperature of 750 °C (1382 °F) for five seconds.
The engine has been running for three seconds.
The diagnostic codes CID-FMI 827-08 and CID-FMI 828-08 are not active.System Response:The ECM will log the event. The ECM derates the engine at 15 second intervals in 2 percent increments when the exhaust inlet temperature is above 750 °C (1382 °F) for five seconds up to a maximum derate of 25 percent. The Fuel limiting function will continue until the exhaust temperature returns below 740 °C (1364 °F). After the temperature returns below 740 °C (1364 °F) the derate due to a high exhaust temperature will be deactivated.
Low power
There may be an exhaust restriction.
There may be an air leak.Test Step 1. Check for "ACTIVE" Diagnostic Codes
Start the Caterpillar Electronic Technician (ET).
Turn the keyswitch to the ON position.
Check for any active diagnostic codes or logged diagnostic codes.Expected Result:There are no diagnostic codes that are present.Results:
OK - There are no diagnostic codes that are present. Proceed to Test Step 2.
Not OK - There are diagnostic codes that are present.Repair: Repair the diagnostic codes that are present. Refer to the appropriate topic in the "Troubleshooting With a Diagnostic Code" section of this manual. Ensure that the repair eliminates the problem.STOPTest Step 2. Perform a Check of the Exhaust System
Perform a check of the exhaust system. Refer to the diagnostic procedure Troubleshooting, "Exhaust Temperature is Too High" for possible causes.Expected Result:There are no problems with the exhaust system.Results:
OK - There may be an intermittent problem.Repair: Monitor the operation of the engine. Repair the problem. Ensure that the repair eliminates the problem.STOP
Not OK - There is a problem with the exhaust system.Repair: Repair the problem. Ensure that the repair eliminates the problem.STOP
Caterpillar SIS machinery equipment:
Parts blade Caterpillar catalog:
3533039
BLADE AS-STRAIGHT
D6T XL
D6T XL
4226316
BLADE AS-UNIVERSAL
D6T XL
D6T XL
4211800
BLADE GP-UNIVERSAL
D6T XL
D6T XL
6V5849
BLADE AS-WIPER
120H, 120H ES, 120H NA, 120M, 120M 2, 12H, 12H ES, 12H NA, 12M, 135H, 135H NA, 140H, 140H ES, 140H NA, 140K, 140M, 140M 2, 143H, 14H, 14H NA, 160H, 160H ES, 160H NA, 160M, 160M 2, 163H, 163H NA, 16H, ...
120H, 120H ES, 120H NA, 120M, 120M 2, 12H, 12H ES, 12H NA, 12M, 135H, 135H NA, 140H, 140H ES, 140H NA, 140K, 140M, 140M 2, 143H, 14H, 14H NA, 160H, 160H ES, 160H NA, 160M, 160M 2, 163H, 163H NA, 16H, ...
1258175
BLADE AS-WIPER
65C, 75C, 75D, 85C, 85D, 953C, 963C, 973C, D3G, D3K XL, D3K2 LGP, D4G, D4K XL, D4K2 XL, D5G, D5K LGP, D5K2 XL, D5N, D5R LGP, D6K, D6K LGP, D6K XL, D6K2, D6K2 LGP, D6N, D6N LGP, D6R, D6R II, D6R III, D...
65C, 75C, 75D, 85C, 85D, 953C, 963C, 973C, D3G, D3K XL, D3K2 LGP, D4G, D4K XL, D4K2 XL, D5G, D5K LGP, D5K2 XL, D5N, D5R LGP, D6K, D6K LGP, D6K XL, D6K2, D6K2 LGP, D6N, D6N LGP, D6R, D6R II, D6R III, D...
6V5851
BLADE AS-WIPER
120G, 120M, 120M 2, 12G, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 140G, 140M, 140M 2, 140M 3, 140M 3 AWD, 14G, 14M, 160M, 160M 2, 160M 3, 160M 3 AWD, 16G, 16M, 24H, 24M, 525B, 535B, 545, 583T, 587R, 587T, ...
120G, 120M, 120M 2, 12G, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 140G, 140M, 140M 2, 140M 3, 140M 3 AWD, 14G, 14M, 160M, 160M 2, 160M 3, 160M 3 AWD, 16G, 16M, 24H, 24M, 525B, 535B, 545, 583T, 587R, 587T, ...
1466433
BLADE AS-WIPER
120M, 120M 2, 12M, 12M 2, 12M 3, 12M 3 AWD, 140M, 140M 2, 140M 3, 140M 3 AWD, 14M, 160M, 160M 2, 160M 3, 160M 3 AWD, 16M, 236D, 242D, 246D, 257D, 259D, 262D, 272D, 272D XHP, 277D, 279D, 287D, 289D, 29...
120M, 120M 2, 12M, 12M 2, 12M 3, 12M 3 AWD, 140M, 140M 2, 140M 3, 140M 3 AWD, 14M, 160M, 160M 2, 160M 3, 160M 3 AWD, 16M, 236D, 242D, 246D, 257D, 259D, 262D, 272D, 272D XHP, 277D, 279D, 287D, 289D, 29...
3341740
BLADE AS-ANGLING
D6T XL
D6T XL
3341765
BLADE AS-ANGLING
D6T XL
D6T XL
3341782
BLADE AS-ANGLING
D6T XL
D6T XL
3751307
BLADE AS
D6T XL
D6T XL
4211800
BLADE GP-UNIVERSAL
D6T XL
D6T XL
4226316
BLADE AS-UNIVERSAL
D6T XL
D6T XL
3533039
BLADE AS-STRAIGHT
D6T XL
D6T XL
3341749
BLADE AS-SEMI-UNIVERSAL
D6T LGP, D6T XL
D6T LGP, D6T XL
3683523
BLADE GP
D6K XL
D6K XL