4250081 BLADE AS-WIPER Caterpillar parts
950 GC
Rating:
Alternative (cross code) number:
CA4250081
425-0081
4250081
CA4250081
425-0081
4250081
Weight: 0.35 pounds 0 kg.
WHEEL LOADER,
Compatible equipment models: 4250081:
Number on catalog scheme:
5
For full view, you need register
Information:
Tilting the Cab
In order to permit easy access to the mechanical components and the hydraulic components, the cab can be tilted forward.The hydraulic pump is operated manually. The hydraulic pump is used in order to raise the cab. The hydraulic pump is used in order to lower the cab.
Illustration 1 g00701209
Turn off the battery disconnect switch. Remove the key.
Illustration 2 g00646542
There are two side panels. One panel is located on the right side of the cab. The other panel is located on the left side of the cab. Remove the side panels in order to gain access to the electrical connectors.
Illustration 3 g00701212
Carefully disconnect all of the electrical connectors.
Illustration 4 g00701208
Remove the nuts and the bolts that are located at each corner of the cab. In order to remove the rear bolts, remove the cover at the two rear corners of the cab. The bolts are under the covers.
Illustration 5 g00701211
Install the pins into the holes for the cab mount pivot. The holes are located under the cab at the front of the cab. The hole on the cab and the hole on the frame are aligned when the cab is in the lowered position. There is one hole on each side of the cab.
Illustration 6 g00701206
The pump is located on the right side of the machine.
Remove the pump handle from the storage location inside the cab. The handle is stored in a compartment behind the seat.
Illustration 7 g00701205
Rotate the valve clockwise to the RAISE position.
Insert the pump handle into the pump. Move the handle upward and move the handle downward in order to raise the cab.
Illustration 8 g00701201
Continue to raise the cab until the two holes are aligned. After the holes are aligned, install the pins into the holes.
Move the valve to the HOLD position. The HOLD position will prevent the buildup of pressure in the hydraulic system.Lowering the Cab
Use the photographs and callouts in Operation and Maintenance Manual, "Raising the Cab"for reference.
Illustration 9 g00701201
Remove the pins from the holes.
Move the valve counterclockwise to the LOWER position.
In order to lower the cab, use the pump handle.
After the cab is lowered, remove all of the pins. Install the bolts and the nuts in the mounts for the cab. Tighten the nuts and the bolts.
In order to permit easy access to the mechanical components and the hydraulic components, the cab can be tilted forward.The hydraulic pump is operated manually. The hydraulic pump is used in order to raise the cab. The hydraulic pump is used in order to lower the cab.
Illustration 1 g00701209
Turn off the battery disconnect switch. Remove the key.
Illustration 2 g00646542
There are two side panels. One panel is located on the right side of the cab. The other panel is located on the left side of the cab. Remove the side panels in order to gain access to the electrical connectors.
Illustration 3 g00701212
Carefully disconnect all of the electrical connectors.
Illustration 4 g00701208
Remove the nuts and the bolts that are located at each corner of the cab. In order to remove the rear bolts, remove the cover at the two rear corners of the cab. The bolts are under the covers.
Illustration 5 g00701211
Install the pins into the holes for the cab mount pivot. The holes are located under the cab at the front of the cab. The hole on the cab and the hole on the frame are aligned when the cab is in the lowered position. There is one hole on each side of the cab.
Illustration 6 g00701206
The pump is located on the right side of the machine.
Remove the pump handle from the storage location inside the cab. The handle is stored in a compartment behind the seat.
Illustration 7 g00701205
Rotate the valve clockwise to the RAISE position.
Insert the pump handle into the pump. Move the handle upward and move the handle downward in order to raise the cab.
Illustration 8 g00701201
Continue to raise the cab until the two holes are aligned. After the holes are aligned, install the pins into the holes.
Move the valve to the HOLD position. The HOLD position will prevent the buildup of pressure in the hydraulic system.Lowering the Cab
Use the photographs and callouts in Operation and Maintenance Manual, "Raising the Cab"for reference.
Illustration 9 g00701201
Remove the pins from the holes.
Move the valve counterclockwise to the LOWER position.
In order to lower the cab, use the pump handle.
After the cab is lowered, remove all of the pins. Install the bolts and the nuts in the mounts for the cab. Tighten the nuts and the bolts.
Caterpillar parts catalog:
Parts blade Caterpillar catalog:
4250078
BLADE AS-WIPER
950 GC
950 GC
4250078
BLADE AS-WIPER
950 GC
950 GC
950F II, 960F, 966F II, 970F
6C4161
BLADE AS-WIPER
950F, 966F, 980F
950F, 966F, 980F
5G4928
BLADE
910
910
5C9211
BLADE AS
920
920
6K9780
BLADE
992
992
8J2840
BLADE
950
950
5K5696
BLADE
966C, 988
966C, 988