AVSPARE.COM
parts catalog

BLADE AS-U 4Z9066 - Caterpillar



4Z9066 BLADE AS-U Caterpillar parts BLADE
Rating:
61
Alternative (cross code) number:
CA4Z9066
4Z-9066
4Z9066
Caterpillar 4Z9066 BLADE AS-U
Weight: 0.80 pounds 0 kg.

Buy BLADE AS-U 4Z9066 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:

Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-7405 Eyebolt 1
B 138-7575 Link Bracket 2
C 138-7576 Link Bracket 2
D - 3/4 inch - 10 NC by 6 inch Guide Bolt 2
E - Loctite 7649 -
F - Loctite 277 - Note: Check the O-ring seals, the gaskets, and the seals for wear or for damage. Replace the components, if necessary.
Illustration 1 g03872965
Install O-ring seal (11).
Illustration 2 g02742396
Install Tooling (D) to the axle housing. Note: Tooling (D) must be modified in order to be used as a guide bolt. Position Tooling (D) in a suitable vice. Remove the head of the bolt in order to use Tooling (D) as a guide bolt.
Install Tooling (C) and a suitable lifting device to the differential and bevel gear assembly. The weight of the rear differential and bevel gear assembly is approximately 415 kg (915 lb). Install the differential and bevel gear assembly to the axle housing.
Remove Tooling (D) from the axle housing.
Apply Tooling (E) then apply Tooling (F) to 45 bolts (10).
Install 45 bolts (10). Tighten 45 bolts (10) to a torque of 475 60 N m (350 44 lb ft).
Illustration 3 g01088537
Attach Tooling (B) and a suitable lifting device to front trunnion support (9). The weight of front trunnion support (9) is approximately 87 kg (192 lb). Install front trunnion support (9) to the pinion housing.
Illustration 4 g01088536
Install yoke assembly (8).
Install manifold (7) to the rear axle housing.
Install clip (6).
Illustration 5 g01088136
Typical example
Install O-ring seal (4) to pin (5).
Use Tooling (A) in order to install pin (5) to the axle housing.
Illustration 6 g01088544
Typical example
Install cover (3) and bolts (1). Tighten bolts (1) evenly to a torque of 47 N m (35 lb ft).
Use a feeler gauge to measure the gap between the axle housing and cover (3).
Subtract 0.05 0.03 mm (0.002 0.001 inch) from the measurement found in Step 14, to give the thickness of shims required.
Remove bolts (1) and cover (3).
Illustration 7 g01088133
Install shims (2), cover (3) and bolts (1). Tighten bolts (1) to a torque of 100 15 N m (75 10 lb ft). End By:
Install the axle shafts. Refer to Disassembly and Assembly, "Axle Shaft - Install".
Install the rear axle assembly. Refer to Disassembly and Assembly, "Oscillating Axle (Rear) - Install".


Parts blade Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.