AVSPARE.COM
parts catalog

BLADE AS-UNIVERSAL 4Z9372 - Caterpillar



4Z9372 BLADE AS-UNIVERSAL Caterpillar parts D9R, D9T BLADE
Rating:
74
Alternative (cross code) number:
CA4Z9372
4Z-9372
4Z9372
Caterpillar 4Z9372 BLADE AS-UNIVERSAL
Weight: 0.010 pounds 0 kg.

Buy BLADE AS-UNIVERSAL 4Z9372 Caterpillar genuine, new aftermarket tractor parts with delivery
TRACK-TYPE TRACTOR,

Compatible equipment models: 4Z9372:

TRACK-TYPE TRACTOR  D9R   D9T   Caterpillar
Number on catalog scheme: 1
 
  For full view, you need register

Information:

Electronic Controls
Electronic Control Module
The ECM consists of two main components, the control computer (hardware) and the flash file (software). The ECM consists of a microprocessor and electronic circuitry. The flash file is the software for the control computer which contains operating maps that define power and torque curves. The ECM monitors the engine parameters during operation. The ECM supplies signals to the injector solenoids.The ECM governs engine speed. Desired engine speed is determined by the throttle signal and by certain sensor readings. Actual engine speed is supplied to the ECM by the engine speed/timing sensor.Fuel Injection
The ECM controls the timing of the engine by varying the signals to the electronic solenoids that control fuel injection. Fuel is injected only while an injector solenoid is energized by a 105 volt signal from the ECM. By controlling the timing and duration of the 105 volt signal, the ECM controls the fuel injection timing, the quantity of fuel and the desired engine speed. Injection timing depends on desired engine speed, load, and other operational factors.The ECM limits engine power during cold mode operation. The ECM may modify the injection timing and the ECM may cut out certain engine cylinders in cold mode operation. This will increase startability and this will reduce warm up time. Cold mode is activated whenever the engine coolant temperature falls below a predetermined value. Cold mode remains active until the engine coolant temperature has risen above a set temperature. The ECM is programmed at the factory to limit the quantity of fuel that can be injected. The position of the Fuel Ratio Control (FRC) controls the fuel limit for exhaust smoke. The FRC is based on the maximum allowable ratio of fuel to air. The FRC fuel position is increased when the ECM senses a higher turbocharger compressor outlet pressure. This will allow more fuel into the cylinder.The rated fuel position is a limit that is based on the engine power rating. This is similar to the rack stops and the torque spring on a mechanically governed engine. The rated fuel position limits the power curve and the torque curve for a specific engine family.Illustration 1 is a block diagram of the engine's electrical system.
Illustration 1 g01239935
Block diagram of engine components
Location of the Engine Components
Illustration 2 g01312507
Left side view
(1) Aftercooler temperature sensor
(2) Engine coolant temperature sensor
(3) Engine speed/timing sensor
(4) Left exhaust temperature sensor Location of the Engine Components
Illustration 3 g01312508
Right side view
(5) Right exhaust temperature sensor
(6) Timing calibration sensor
(7) Crankcase pressure sensor Location of the Engine Components
Illustration 4 g01312509
Front and back view
(2) Coolant temperature sensor
(1) Aftercooler temperature sensor
(8) Turbocharger compressor outlet pressure sensor
(9) Atmospheric pressure sensor
(10) Left turbocharger compressor inlet pressure sensor
(4) Left exhaust temperature sensor
(5) Right exhaust temperature sensor
(11) Right turbocharger compressor inlet pressure sensor
(12) ECM connector J1
(13) ECM
(14) ECM connector J2 Location of the Engine Components
Illustration 5 g01241242
Right front
(15) Filtered engine oil pressure sensor
(16) Unfiltered fuel pressure sensor
(17) Filtered fuel pressure sensor
(18) Unfiltered engine oil pressure sensor

Caterpillar SIS machinery equipment:

Caterpillar SIS

Caterpillar parts catalog:

Caterpillar parts catalog
D9R Custom Parts Manual 7TL00001-UP (MACHINE) POWERED BY 3408 Engine
D9R CUSTOM PARTS MANUAL ABK00001-UP (MACHINE)
D9T Track-Type Tractor RJS00001-UP (MACHINE) POWERED BY C18 Engine
D9R TRACK-TYPE TRACTOR WDM00001-UP (MACHINE) POWERED BY 3408C Engine
D9T TRACK-TYPE TRACTOR TWG00001-UP (MACHINE) POWERED BY C18 Engine


Parts blade Caterpillar catalog:

6V5849 BLADE AS-WIPER
120H, 120H ES, 120H NA, 120M, 120M 2, 12H, 12H ES, 12H NA, 12M, 135H, 135H NA, 140H, 140H ES, 140H NA, 140K, 140M, 140M 2, 143H, 14H, 14H NA, 160H, 160H ES, 160H NA, 160M, 160M 2, 163H, 163H NA, 16H, ...
5C8811 BLADE AS-WIPER
120M, 120M 2, 12M, 12M 2, 12M 3, 12M 3 AWD, 140M, 140M 2, 140M 3, 140M 3 AWD, 14M, 160M, 160M 2, 160M 3, 160M 3 AWD, 16M, 215, 227, 229, 245, 35, 414E, 416C, 416E, 416F, 420D, 420E, 420F, 422E, 426C, ...
6W3924 BLADE AS-WIPER
216, 216B, 226B, 232B, 236, 236B, 242B, 247, 247B, 248, 252B, 257B, 267, 267B, 268B, 287, 312B L, 315B L, 317B LN, 318B, 330 L, 350 L, 365B, 365B II, 385B, 65, 65C, 65E, 69D, 75C, 75D, 75E, 814B, 815B...
6V5851 BLADE AS-WIPER
120G, 120M, 120M 2, 12G, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 140G, 140M, 140M 2, 140M 3, 140M 3 AWD, 14G, 14M, 160M, 160M 2, 160M 3, 160M 3 AWD, 16G, 16M, 24H, 24M, 525B, 535B, 545, 583T, 587R, 587T, ...
8J4657 BLADE GP-STRAIGHT
5S, 6A, 6S, D6D, D6D SR
2824580 BLADE GP-STRAIGHT
311D LRR, 311F LRR, 312D, 312D L, 312D2, 312E, 312E L, 313D, 314D CR, 314D LCR, 314E CR, 314E LCR
2436702 BLADE GP
120M, 120M 2, 12M, 12M 2, 12M 3, 12M 3 AWD, 140M, 140M 2, 140M 3, 140M 3 AWD, 160M, 160M 2, 160M 3, 160M 3 AWD
2570197 BLADE & MOUNTING GP
M316C, M316D, M318C, M318D
2795387 BLADE GP-MULTIPURPOSE BUCKET
216, 216B, 216B3, 226B, 226B3, 228, 232B, 236, 236B, 236B3, 242B, 242B3, 246C, 247, 247B, 247B3, 248, 252B, 252B3, 256C, 257B, 257B3, 259B3, 262C, 267, 267B, 268B, 272C, 277C, 279C, 287, 287C, 289C, 2...
8E5204 BLADE AS-SEMI-UNIVERSAL
D6H, D6H II, D6H XL, D6H XR, D6R, D6R II
3828822 BLADE & MOUNTING GP
308E, 308E CR, 308E SR, 308E2 CR
9U8095 BLADE & EDGE GP
D6H, D6H XL, D6H XR, D6R, D6R II
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.