3927633 BLOCK Caterpillar parts
Rating:
Alternative (cross code) number:
CA3927633
392-7633
3927633
CA3927633
392-7633
3927633
You can buy:
US$85.62
15 Jul 2025
FridayParts
US$127.49
29 May 2025
FridayParts
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
FridayParts Fuel Pipe 3927633 3966863 Compatible for Cummins Engine 4B3.9 B5.9 GAS PLUS CM556 Replacement
FP FRIDAYPARTS New aftermarket parts; the picture is just for reference || Part Number: 3927633, 3966863 || Compatible for Cummins Engine 4B3.9 B5.9 GAS PLUS CM556 || Please verify your part number before ordering, if you have any question please don't hesitate to contact us
FP FRIDAYPARTS New aftermarket parts; the picture is just for reference || Part Number: 3927633, 3966863 || Compatible for Cummins Engine 4B3.9 B5.9 GAS PLUS CM556 || Please verify your part number before ordering, if you have any question please don't hesitate to contact us
VIIKEND Fuel Manifold 3927633 3966863 392-7633 Compatible with Cummins Engine 4B3.9 6C8.3 B3.3 B4.5 QSB6.7
VIIKEND Part Name: Fuel Manifold || Part Number: 3927633 3966863 392-7633 Note: Please check the fitment carefully before purchase. Or just tell us the part number you need. || Engine Model: QSB6.7 || Applicable: Compatible with Cummins Engine 4B3.9 6C8.3 B3.3 B4.5 QSB6.7 || Package included: 1pcs Fuel Manifold 3927633 3966863 392-7633
VIIKEND Part Name: Fuel Manifold || Part Number: 3927633 3966863 392-7633 Note: Please check the fitment carefully before purchase. Or just tell us the part number you need. || Engine Model: QSB6.7 || Applicable: Compatible with Cummins Engine 4B3.9 6C8.3 B3.3 B4.5 QSB6.7 || Package included: 1pcs Fuel Manifold 3927633 3966863 392-7633
HOLDWELL Fuel Return Line 3927633 3966863 Compatible with Cummins Engine B5.9 4B3.9 6C8.3 B3.3 B4.5 ISB CM2150 ISB6.7 CM2250 Hyundai Wheel Loader HL730-7 HM730TM-7 HL720-3C Crawler Dozer H70 H80
HOLDWELL Part Number: 3927633, 3966863 || Application: For Cummins Engine: B5.9, 4B3.9, 6C8.3, B3.3, B4.5, ISB CM2150, ISB6.7 CM2250, ISB6.7 CM2350 B101, ISBE4 CM850, ISC CM2150, ISC8.3 CM2250, ISL9 CM2350 L101, QSB3.9 30 CM550, QSB4.5 30 CM550, QSB6.7 CM2250 || Application: For Hyundai Wheel Loader: HL730-7, HM730TM-7, HL720-3C; For Hyundai Crawler Dozer: H70, H80; For Hyundai Excavator: R140LC-7, R140LC9S,R140W-7, R140W9S || Package Included: 1 x Fuel Return Line || We will try our best to provide a great quality service and a nice shopping experience. If you have any questions, please feel free to contact us. Thanks!
HOLDWELL Part Number: 3927633, 3966863 || Application: For Cummins Engine: B5.9, 4B3.9, 6C8.3, B3.3, B4.5, ISB CM2150, ISB6.7 CM2250, ISB6.7 CM2350 B101, ISBE4 CM850, ISC CM2150, ISC8.3 CM2250, ISL9 CM2350 L101, QSB3.9 30 CM550, QSB4.5 30 CM550, QSB6.7 CM2250 || Application: For Hyundai Wheel Loader: HL730-7, HM730TM-7, HL720-3C; For Hyundai Crawler Dozer: H70, H80; For Hyundai Excavator: R140LC-7, R140LC9S,R140W-7, R140W9S || Package Included: 1 x Fuel Return Line || We will try our best to provide a great quality service and a nice shopping experience. If you have any questions, please feel free to contact us. Thanks!
For full view, you need register
Information:
Description of the Universal Network Interface (UNI) Board
Illustration 1 g01277304
(1) Universal network interface (UNI) board The universal network interface (UNI) board is only in the flywheel cabinet.The Backup UPSNet is a backup internal communication port that works with the Primary UPSNet port on the system I/O. If a remote status panel is installed on the system, the panel will be connected to the dedicated port.Removal Procedure
Refer to Systems Operation, Testing and Adjusting, UENR3954, "Internal Component Preremoval Steps (Flywheel Cabinet)" in order to shut down the system and gain access to internal components.
Electrostatic discharge can damage integrated circuits or semiconductors if you touch bus connector pins. When not in use, keep the module in a static-shield bag. Follow these guidelines when you handle any module:Touch a grounded object to discharge static potential.Wear an approved wrist-strap grounding device.Do not touch the bus connector or connector pins.Do not touch circuit components inside the module.If available, use a static-safe work station.
Illustration 2 g01277384
UNI board
Disconnect all connectors. Refer to Illustration 2. Verify each label for each connector for subsequent installation.
Remove the ground screw from the "J6" connector.
Disconnect the white plastic standoffs that connect the board (1) to the left panel. Note: The UNI board (1) must be removed from the standoffs without bending the board.
Compress the head of each standoff so that the board (1) is not locked, but the board is still attached to the standoff.
Remove the board (1) from all standoffs at the same time. Installation Procedure
Electrostatic discharge can damage integrated circuits or semiconductors if you touch bus connector pins. When not in use, keep the module in a static-shield bag. Follow these guidelines when you handle any module:Touch a grounded object to discharge static potential.Wear an approved wrist-strap grounding device.Do not touch the bus connector or connector pins.Do not touch circuit components inside the module.If available, use a static-safe work station.
Position the board (1) in the cabinet over the white standoffs that are connected to the left panel. Install the board (1). Verify that all the standoffs are locked into the correct position.
Install the ground screw on the "J6" connector on the left panel.
Connect the wire connectors. Verify the labeling of each connector for proper placement. Refer to Illustration 2.
Table 1
Fuse Type
SIOD-F2 250 VAC 1 A
SIOD-F3 250VAC 2 A
SIOD-F4 250 VAC 2 A
SIOD-F5 250 VAC 2 A
Illustration 1 g01277304
(1) Universal network interface (UNI) board The universal network interface (UNI) board is only in the flywheel cabinet.The Backup UPSNet is a backup internal communication port that works with the Primary UPSNet port on the system I/O. If a remote status panel is installed on the system, the panel will be connected to the dedicated port.Removal Procedure
Refer to Systems Operation, Testing and Adjusting, UENR3954, "Internal Component Preremoval Steps (Flywheel Cabinet)" in order to shut down the system and gain access to internal components.
Electrostatic discharge can damage integrated circuits or semiconductors if you touch bus connector pins. When not in use, keep the module in a static-shield bag. Follow these guidelines when you handle any module:Touch a grounded object to discharge static potential.Wear an approved wrist-strap grounding device.Do not touch the bus connector or connector pins.Do not touch circuit components inside the module.If available, use a static-safe work station.
Illustration 2 g01277384
UNI board
Disconnect all connectors. Refer to Illustration 2. Verify each label for each connector for subsequent installation.
Remove the ground screw from the "J6" connector.
Disconnect the white plastic standoffs that connect the board (1) to the left panel. Note: The UNI board (1) must be removed from the standoffs without bending the board.
Compress the head of each standoff so that the board (1) is not locked, but the board is still attached to the standoff.
Remove the board (1) from all standoffs at the same time. Installation Procedure
Electrostatic discharge can damage integrated circuits or semiconductors if you touch bus connector pins. When not in use, keep the module in a static-shield bag. Follow these guidelines when you handle any module:Touch a grounded object to discharge static potential.Wear an approved wrist-strap grounding device.Do not touch the bus connector or connector pins.Do not touch circuit components inside the module.If available, use a static-safe work station.
Position the board (1) in the cabinet over the white standoffs that are connected to the left panel. Install the board (1). Verify that all the standoffs are locked into the correct position.
Install the ground screw on the "J6" connector on the left panel.
Connect the wire connectors. Verify the labeling of each connector for proper placement. Refer to Illustration 2.
Table 1
Fuse Type
SIOD-F2 250 VAC 1 A
SIOD-F3 250VAC 2 A
SIOD-F4 250 VAC 2 A
SIOD-F5 250 VAC 2 A
Parts block Caterpillar catalog:
3927632
BLOCK
Caterpillar
Caterpillar
3927631
BLOCK
Caterpillar
Caterpillar
3924185
BLOCK AS
Caterpillar
Caterpillar
3922003
BLOCK-CYLINDER
Caterpillar
Caterpillar
3899093
BLOCK-SUPPORT
Caterpillar
Caterpillar
3898037
BLOCK
Caterpillar
Caterpillar
3938038
BLOCK
Caterpillar
Caterpillar
3938037
BLOCK
Caterpillar
Caterpillar
3938036
BLOCK
Caterpillar
Caterpillar
3928867
BLOCK-SHIFT
Caterpillar
Caterpillar
3928328
BLOCK
Caterpillar
Caterpillar
3927634
BLOCK
Caterpillar
Caterpillar