1466372 BLOWER AS Caterpillar parts
216, 228, 236, 248, 267, 301.5, 302.5, 303.5, 304.5
Rating:
Alternative (cross code) number:
CA1466372
146-6372
1466372
CA1466372
146-6372
1466372
Weight: 3 pounds 1 kg.
MINI HYD EXCAVATOR, SKID STEER LOADER,
Compatible equipment models: 1466372:
Number on catalog scheme:
5
For full view, you need register
Information:
Removal Procedure
Drain the engine oil into a suitable container for storage or disposal.
Illustration 1 g02440317
Remove guard assemblies (1).
Illustration 2 g02440318
Typical example.
Remove dip stick (2).
Illustration 3 g02440319Note: Mark the location for each of bolts (5). The bolts are not all the same length.
Remove hose assembly (3), harness assembly (4), bolts (5), oil pan (6), and the gasket.
Illustration 4 g02440322
Remove bolts (7) and spacer (8).Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Guide Stud
M8 by 100mm 4
B - Loctite 593 Silicone Sealer -
Illustration 5 g02440322
Install spacer (8) and bolts (7).
Illustration 6 g02440358
Install Tooling (A) in Locations (X). Install the gasket and oil pan (6).
Illustration 7 g02440376
Illustration 8 g02440378
Install bolts (5). Tighten bolts (5) in the sequence shown, to a torque of 22 N m (195 lb in).
Remove Tooling (A). Install the remainder of bolts (5). Tighten bolts (5) in the sequence shown, to a torque of 22 N m (195 lb in).
Illustration 9 g02441036
Install hose assembly (3) and harness assembly (4).
Illustration 10 g02440318
Apply Tooling (B) to the nut and install dip stick (2).
Illustration 11 g02440317
Install guard assemblies (1).End By:
Fill the engine oil. Refer to Operations and Maintenance Manual, "Engine Oil - Change" for the correct draining and filling procedures.
Drain the engine oil into a suitable container for storage or disposal.
Illustration 1 g02440317
Remove guard assemblies (1).
Illustration 2 g02440318
Typical example.
Remove dip stick (2).
Illustration 3 g02440319Note: Mark the location for each of bolts (5). The bolts are not all the same length.
Remove hose assembly (3), harness assembly (4), bolts (5), oil pan (6), and the gasket.
Illustration 4 g02440322
Remove bolts (7) and spacer (8).Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Guide Stud
M8 by 100mm 4
B - Loctite 593 Silicone Sealer -
Illustration 5 g02440322
Install spacer (8) and bolts (7).
Illustration 6 g02440358
Install Tooling (A) in Locations (X). Install the gasket and oil pan (6).
Illustration 7 g02440376
Illustration 8 g02440378
Install bolts (5). Tighten bolts (5) in the sequence shown, to a torque of 22 N m (195 lb in).
Remove Tooling (A). Install the remainder of bolts (5). Tighten bolts (5) in the sequence shown, to a torque of 22 N m (195 lb in).
Illustration 9 g02441036
Install hose assembly (3) and harness assembly (4).
Illustration 10 g02440318
Apply Tooling (B) to the nut and install dip stick (2).
Illustration 11 g02440317
Install guard assemblies (1).End By:
Fill the engine oil. Refer to Operations and Maintenance Manual, "Engine Oil - Change" for the correct draining and filling procedures.
Caterpillar parts catalog:
Parts blower Caterpillar catalog:
1337469
BLOWER AS
416C, 426C, 428C, 436C, 438C, 928G
416C, 426C, 428C, 436C, 438C, 928G
1471483
BLOWER AS
416C, 426C, 428C, 436C, 438C
416C, 426C, 428C, 436C, 438C
1455344
BLOWER
TH103, TH62, TH63, TH82, TH83
TH103, TH62, TH63, TH82, TH83
416B, 426B, 428B, 438B, 446B
3Y0714
BLOWER FAN AND GUARD
D5, D5B
D5, D5B
120M, 3412C, 966H, C27, C32
236D, 242D, 246D, 257D, 259D, 262D, 272D, 272D XHP, 277D, 279D, 287D, 289D, 299D, 299D XHP
416E, 416F, 420E, 420F, 422E, 422F, 428E, 428F, 430E, 430F, 432E, 432F, 434E, 434F, 442E, 444E, 444F, 450E, D3G, D4G, D5G
1741227
BLOWER AS
TH220B, TH330B, TH340B, TH350B, TH355B, TH460B, TH560B, TH580B
TH220B, TH330B, TH340B, TH350B, TH355B, TH460B, TH560B, TH580B
2043125
BLOWER GP-CAB
TH210, TH215
TH210, TH215
416D, 416E, 420D, 420E, 424D, 428D, 430D, 430E, 432D, 438D, 442D, 446D