AVSPARE.COM
parts catalog

BODY 5M4999 - Caterpillar


5M4999 BODY Caterpillar parts 651, 657, 657B, 666
Rating:
45
Alternative (cross code) number:
CA5M4999
5M-4999
5M4999
Caterpillar 5M4999 BODY
Weight: 0.010 pounds 0 kg.

Buy BODY 5M4999 Caterpillar genuine, new aftermarket tractor parts with delivery
WHEEL SCRAPER, WHEEL TRACTOR,

Compatible equipment models: 5M4999:

WHEEL SCRAPER  657   657B  
WHEEL TRACTOR  651   657   666   Caterpillar
Number on catalog scheme: None
  For full view, you need register

Information:


Connect the 198-4237 Pressure Sensor to the pressure tap for Clutch 1. See Illustration 2 for the locations of all the pressure taps. Use the 198-4236 Adapter Cable in order to connect the pressure sensor to the 198-4234 Digital Indicator .
Make sure that the transmission direction switch is in the NEUTRAL position.
Make sure that the parking brake is engaged.
Start the engine.
Illustration 3 g01130612
The transmission oil temperature gauge should be at the center position.
Warm the transmission oil above approximately 40 °C (104 °F).
Illustration 4 g01107110
(A) Number 6 clutch (First gear) (B) Number 1 clutch (Reverse) (C) Number 5 clutch (Second gear) (D) Number 4 clutch (Third gear) (E) Number 2 clutch (Forward) (F) Number 3 clutch (Fourth gear)Note: If a new clutch solenoid modulating valve was installed, shift the transmission at least 12 times into a speed or a direction that uses the clutch solenoid modulating valve. Refer to Illustration 4 in order to identify the clutch solenoid modulating valve and the corresponding clutch. Allow sufficient time for the corresponding clutch to be fully pressurized.
Operate the engine at low idle.
Table 4
Clutch Engagement Calibration Submodes    
Submode 31     Number 1 Clutch Engagement
Reverse    
Submode 32     Number 2 Clutch Engagement
Forward    
Submode 33     Number 3 Clutch Engagement
Fourth Speed    
Submode 34     Number 4 Clutch Engagement
Third Speed    
Submode 35     Number 5 Clutch Engagement
Second Speed    
Submode 36     Number 6 Clutch Engagement
First Speed    
Illustration 5 g01107535
Service connector
Connect the 4C-8195 Control Service Tool to the service connector in the cab. The service connector is located on the back wall of the cab to the right of the operators station.
Use the 4C-8195 Control Service Tool to enter Transmission Calibration Mode 8 via the "MODE" switch.Note: The following procedure uses submode 31 to calibrate the number 1 Clutch. Refer to Table 4 for the correct submode for the clutch that is being calibrated.
Press and release the "CLEAR" switch. The Caterpillar Monitoring System display will read 81 27. Press the "CLEAR" switch until the display reads 81 31. Release the "CLEAR" switch.
If all the conditions are correct for calibration, the pressure for the particular clutch is shown in the display area of the Caterpillar Monitoring System. The units of the value that is displayed is 10 kPa. Multiply the value that is shown in the display by 10 to determine the true specified value in kPa. Record the value.In the remaining steps, adjustments are made so that this pressure is the actual pressure gauge reading. The pressure is also listed in Table 5.Note: If the conditions are not correct for calibration, the pressure is not shown in the display area. Instead, an error code (EXX) appears. The calibration will not run until all necessary conditions are met. Correct the error code and perform these procedures again. Refer to Table 1 for a list of the error codes and the meaning of the error codes.
When all conditions are met and the pressure is shown in the display area, shift the transmission direction control

Caterpillar parts catalog:

Caterpillar parts catalog
657 TRACTOR 46M00001-00177 (MACHINE)
657 SCRAPERS 47M00001-00111 (MACHINE)
666 SCRAPER 20G00176-00241 (MACHINE)
641 & 651 TRACTORS 33G00001-00155 (MACHINE)
657 SCRAPER 19G00001-00516 (MACHINE)
641 & 651 TRACTORS 33G00001-00155 (MACHINE)
657 SCRAPER 19G00001-00516 (MACHINE)
641 & 651 TRACTORS 33G00001-00155 (MACHINE)
657 SCRAPER 19G00001-00516 (MACHINE)
657 TRACTOR 31G00232-00578 (MACHINE)
641 & 651 TRACTORS 33G00001-00155 (MACHINE)
657 SCRAPER 19G00001-00516 (MACHINE)
666 SCRAPER 20G00001-00175 (MACHINE)
641 & 651 TRACTORS 33G00156-00279 (MACHINE)
657 TRACTOR 31G00232-00578 (MACHINE)
657 SCRAPER 19G00001-00516 (MACHINE)
666 SCRAPER 20G00001-00175 (MACHINE)
641 & 651 TRACTORS 41M00001-UP (MACHINE)
666 SCRAPER 20G00176-00241 (MACHINE)
657B SCRAPERS 47M00001-UP (MACHINE)
666B SCRAPER 20G00242-UP (MACHINE) POWERED BY D343 ENGINE
657 SCRAPERS 47M00001-00111 (MACHINE)
641 & 651 TRACTORS 33G00156-00279 (MACHINE)
641 & 651 TRACTORS 33G00280-00336 (MACHINE)
657 TRACTOR 31G00232-00578 (MACHINE)
666 TRACTOR 64H00001-UP (MACHINE)
657 TRACTOR 31G00001-00231 (MACHINE)


Parts body Caterpillar catalog:

2D6393 BODY
631C, 769C, 777
5J9732 BODY GROUP
641, 641B, 650B, 651
5J9733 BODY GROUP
650B, 657, 657B, 666
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.