BOGIE AS-FRONT 1287256 - Caterpillar

1287256 BOGIE AS-FRONT Caterpillar parts D11N, D11R, D11T

Price: query
Add in request price Go to cart

Rating:

Alternative (cross code) number:
CA1287256
128-7256
1287256

Weight: 892 pounds 404 kg.

Buy BOGIE AS-FRONT 1287256 Caterpillar genuine, new aftermarket tractor parts with delivery
TRACK-TYPE TRACTOR,

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below

$4,132.98

24 Feb 2019

CATERPILLAR AFTERMARKET: CATERPILLAR AFT

Caterpillar Bogie AS-Front 1287256 New

Caterpillar 128-7256 Common Undercarriage (1287256)

$4,528.93

14 Mar 2020
893.97447241[401.85] Poun
-: -

Caterpillar 128-7256 Common Undercarriage (1287256)
1287256 Caterpillar, Undercarriage Parts Weight(lbs): 892.00 Length(cm): 81.5000 Width(cm): 121.5000 Depth(cm): 69.0000

$5,208.68

21 Jan 2019

BOGIE AS-FRONT

Show more prices Caterpillar parts

This part in 1 request: Show. This information for suppliers only!

#614536 128-7256

2021-03-11

Number on catalog scheme: 6

Caterpillar 1287256 Parts scheme BOGIE AS-FRONT

For full view, you need register

Compatible equipment models: 1287256:

TRACK-TYPE TRACTOR D11N D11R D11T Caterpillar

Information:

Use this procedure in order to troubleshoot an occurrence for a start inhibit or a stop request from the driven equipment or use this procedure if one of the following event codes is active. Refer to Troubleshooting, "Event Codes" for information about event codes. You must access the engine monitoring system on Caterpillar Electronic Technician (ET) in order to view the current trip points for these codes. For information on the engine monitoring system, refer to Troubleshooting, "Engine Monitoring System".
Table 1
Event Code
Description Conditions which Activate the Code System Response
E226(3) Driven Equipment Start Inhibit The Electronic Control Module (ECM) has received a signal which indicates that the driven equipment is not ready for the engine to start. The code is logged.
The shutdown output is activated.
Engine cranking is prevented.
E270(3) Driven Equipment Shutdown Requested While the engine is running, the ECM has received a signal which indicates that the driven equipment must be shut down. The code is logged.
The shutdown output is activated.
The engine is shut down. Probable Causes
Request from the driven equipment
Faulty circuit for the driven equipmentRecommended Actions
Request from the Driven Equipment
Determine whether the driven equipment has generated a request for the start inhibit or for the shutdown. Determine the cause for the request. Service the driven equipment according to the recommendations of the Original Equipment Manufacturer (OEM) of the equipment.Faulty Circuit for the Driven Equipment
Note: The circuit for the driven equipment input must remain closed in order for the engine to run.Inspect the wiring of the circuit and the P1 connector for the ECM. Look for damage and/or corrosion. Refer to Troubleshooting, "Electrical Connectors - Inspect" for information that is related to inspecting electrical connectors.Perform the following procedure to check the circuits for the driven equipment:
Disconnect the P1 ECM connector.
Fabricate a jumper wire that is long enough to create a test circuit across the harness connector for the switch that is at the driven equipment.
Create a continuous circuit by using the jumper wire to short circuit the terminals at the harness connector for the switch.
Use a multimeter to measure the resistance between terminals P1-21 and P1-31 at the connector for the ECM. Continuity must be measured for the circuit in order for the ECM to detect normal engine operation.
If the circuit does not have continuity, locate the source of the excessive resistance in the circuit. Perform the necessary repairs.