1564208 BOGIE-MINOR Caterpillar parts
D10R, D10T
Rating:
Alternative (cross code) number:
CA1564208
156-4208
1564208
CA1564208
156-4208
1564208
Weight: 52 pounds 23 kg.
TRACK-TYPE TRACTOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
CTP 1564208 Bogie Minor for Model D10R, Right
CTP For Model D10R || Right || Sold in each || Country of origin: United States
CTP For Model D10R || Right || Sold in each || Country of origin: United States
O2 Oxygen Sensor Compatible with 2004-2011 Saab 9-3 2010-2011 9-3X 2001-2005 Saturn L300 2000 LS2 LW2 2001-2003 LW300
AM Autoparts 10 Year Warranty || Reference Number(s): 0258006064,0258006175,0258006200,0258006447,0258006622,0258006624,09182000,1564208,1564403,16064,16175,16196,16200,16447,16622,16624,2133010,2344822,2344867,2344910,2344913,25024353,4570917,55353149,8670130,86701300,9182000,9470011,94700110,9470571,ES10732,ES20115,FE80173,FE80190,FE80707,LS6064,LS6175,LS6200,LS6447,LS6624,SG1073,SG1090,SG1526,SU1329,SU5863,SU6071,SU7808,V50760001,V95760020
AM Autoparts 10 Year Warranty || Reference Number(s): 0258006064,0258006175,0258006200,0258006447,0258006622,0258006624,09182000,1564208,1564403,16064,16175,16196,16200,16447,16622,16624,2133010,2344822,2344867,2344910,2344913,25024353,4570917,55353149,8670130,86701300,9182000,9470011,94700110,9470571,ES10732,ES20115,FE80173,FE80190,FE80707,LS6064,LS6175,LS6200,LS6447,LS6624,SG1073,SG1090,SG1526,SU1329,SU5863,SU6071,SU7808,V50760001,V95760020
Number on catalog scheme:
15
For full view, you need register
Information:
Use this procedure if any one of the diagnostic codes in Table 1 is active.
Table 1
Diagnostic Codes Table
Code Conditions which Generate this Code System Response
268-2 Programmed Parameter Fault : Erratic, Intermittent, or Incorrect The engine Electronic Control Module (ECM) detects that one or more of the programmable parameters have not been programmed. The ECM may use a default torque map or the ECM may limit the engine to low idle.
The code is active only.
1495-2 Injector Trim Codes Not Programmed The engine ECM detects that one or more of the trim codes for the injectors have not been programmed. The ECM may use a default torque map or the ECM may limit the engine to low idle.
The code is active only. Some system configuration parameters are configurable by the customer in order to suit the customer particular application. The configuration file contains all of the adjustable settings for the monitoring system. The engine is shipped from the factory with default values for these parameters. In most cases, the parameters do not require change. The system configuration parameters must be reprogrammed if an ECM is replaced and/or the engine rating is reprogrammed. System configuration parameters do not require change if the flash file is replaced. Proper values for these parameters are available on Caterpillar Electronic Technician (ET). Certain configuration parameters are also stamped on the engine information plate.If the default settings for the parameters have been modified, there will be no record at the factory of the changes. These settings can be downloaded into a laptop computer and saved to a file. The customer can then use the file in order to ease the future replacement of the ECM.Note: Changing the parameters that are protected by factory passwords may cause your Caterpillar warranty to be voided.Check Programmable Parameters (268-2)
If a programmable parameter has not been programmed, the ECM will generate a 268-2 Check Programmable Parameters diagnostic code. The unprogrammed parameters will be set to default. Certain aspects of the engine performance and engine monitoring may be affected. Program the missing parameter.Injector Trim Codes Not Programmed (1495-2)
The engine ECM detects that one or more of the "injector trim codes" have not been programmed. The injector code is a number that is found on each of the unit injectors. The ECM uses this number to compensate for manufacturing variations between individual injectors. If you replace any of the unit injectors, reprogram the code for the new injectors. Also, if you replace the ECM, reprogram all of the injector codes.Note: The injector codes are not part of the "Configuration" screen on Cat ET. "Injector Codes Calibration" can be found under "Calibrations" in the "Service" menu on Cat ET.
Engine Serial Number
Program the engine serial number to match the engine information plate. The serial number is not programmed on a new ECM.Rated Fuel Position
This parameter is used to set engine power. A factory password is required to change this setting.
Table 2
Minimum
Table 1
Diagnostic Codes Table
Code Conditions which Generate this Code System Response
268-2 Programmed Parameter Fault : Erratic, Intermittent, or Incorrect The engine Electronic Control Module (ECM) detects that one or more of the programmable parameters have not been programmed. The ECM may use a default torque map or the ECM may limit the engine to low idle.
The code is active only.
1495-2 Injector Trim Codes Not Programmed The engine ECM detects that one or more of the trim codes for the injectors have not been programmed. The ECM may use a default torque map or the ECM may limit the engine to low idle.
The code is active only. Some system configuration parameters are configurable by the customer in order to suit the customer particular application. The configuration file contains all of the adjustable settings for the monitoring system. The engine is shipped from the factory with default values for these parameters. In most cases, the parameters do not require change. The system configuration parameters must be reprogrammed if an ECM is replaced and/or the engine rating is reprogrammed. System configuration parameters do not require change if the flash file is replaced. Proper values for these parameters are available on Caterpillar Electronic Technician (ET). Certain configuration parameters are also stamped on the engine information plate.If the default settings for the parameters have been modified, there will be no record at the factory of the changes. These settings can be downloaded into a laptop computer and saved to a file. The customer can then use the file in order to ease the future replacement of the ECM.Note: Changing the parameters that are protected by factory passwords may cause your Caterpillar warranty to be voided.Check Programmable Parameters (268-2)
If a programmable parameter has not been programmed, the ECM will generate a 268-2 Check Programmable Parameters diagnostic code. The unprogrammed parameters will be set to default. Certain aspects of the engine performance and engine monitoring may be affected. Program the missing parameter.Injector Trim Codes Not Programmed (1495-2)
The engine ECM detects that one or more of the "injector trim codes" have not been programmed. The injector code is a number that is found on each of the unit injectors. The ECM uses this number to compensate for manufacturing variations between individual injectors. If you replace any of the unit injectors, reprogram the code for the new injectors. Also, if you replace the ECM, reprogram all of the injector codes.Note: The injector codes are not part of the "Configuration" screen on Cat ET. "Injector Codes Calibration" can be found under "Calibrations" in the "Service" menu on Cat ET.
Engine Serial Number
Program the engine serial number to match the engine information plate. The serial number is not programmed on a new ECM.Rated Fuel Position
This parameter is used to set engine power. A factory password is required to change this setting.
Table 2
Minimum
Caterpillar parts catalog:
Parts bogie Caterpillar catalog:
D10N, D10R, D10T, D10T2, D9L
D10R, D10T
7T0376
BOGIE AS
D10N, D10R, D10T, D9L
D10N, D10R, D10T, D9L
D10N, D10R, D10T, D10T2, D9L
D10N, D10R, D10T, D9L
D10R, D10T, D10T2
D10R, D10T
3623566
BOGIE AS
D10R, D10T, D10T2
D10R, D10T, D10T2
D10N, D10R, D10T, D10T2, D9L
D9R, D9T
D9R, D9T
D9N, D9R, D9T
D11R
D11R, D11T
D11R, D11T
D11R, D11T
D11N, D11R, D11T
D10R, D10T