2618287 BOGIE-MINOR Caterpillar parts
D11R, D11T
Rating:
Alternative (cross code) number:
CA2618287
261-8287
2618287
CA2618287
261-8287
2618287
Weight: 65 pounds 29 kg.
TRACK-TYPE TRACTOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$7.99
07 Jun 2023
CN: CCZ-US-
LaoXing Car Interior Decoration Personality Pendant The Joker Model Rearview Mirror Pendant Decoration Car Goods Interior Accessories
LaoXing MATERIAL: made of eco-friendly resin, safe and odorless. || Size: clown is 2*1.6 inch/ approx 5*4cm, total length is approx 12 inch/ 30cm. || IDEAL DECORATION: suitable for hanging on car rearview mirrors, add fun to our driving; a good decor for halloween party; an ideal gift for friends,family, etc. || FEATURES: The clown is in small size, will not affect the driving sight, and the lanyard is not too long, invoid to hit the glass when braking. and shake slightly when driving, which can well eliminate the driver's visual fatigue and increase safety. || PACKAGE INCLUDES: 1 Clown Hanging Ornaments.
LaoXing MATERIAL: made of eco-friendly resin, safe and odorless. || Size: clown is 2*1.6 inch/ approx 5*4cm, total length is approx 12 inch/ 30cm. || IDEAL DECORATION: suitable for hanging on car rearview mirrors, add fun to our driving; a good decor for halloween party; an ideal gift for friends,family, etc. || FEATURES: The clown is in small size, will not affect the driving sight, and the lanyard is not too long, invoid to hit the glass when braking. and shake slightly when driving, which can well eliminate the driver's visual fatigue and increase safety. || PACKAGE INCLUDES: 1 Clown Hanging Ornaments.
$571.43
24 Dec 2021
US: Florida-Parts-Z
2618287-MINOR 9W6723 for Caterpillar (CAT)
FIRST PRICE PARTS
FIRST PRICE PARTS
$537.64
14 Oct 2021
Amazon.com
CTP 2618287 Bogie Minor for Model D11R/D11T
CTP For Model D11R/D11T || Sold in each || Easy in-and-out fit
CTP For Model D11R/D11T || Sold in each || Easy in-and-out fit
Number on catalog scheme:
9
For full view, you need register
Information:
When an engine is first installed, the following steps must be completed for the initial setup of the Air/Fuel Ratio Control (AFRC).
Ensure that the engine controller is set to the correct engine configuration. Refer to Systems Operation, "Reset to Start". Selecting the improper configuration will cause bad engine response.
Open the power valve in order to eliminate any restriction in fuel flow. Turn the valve counterclockwise by three to four turns.
Position the control valve to the START position of 350 steps for the G3412 and G3516 engines. Position the control valve to the START position of 800 steps for the G3408 engine. Ensure that the switch is in the manual mode.
Bring the engine up to rated speed and load. Do not exceed the rated load. While the AFRC is still in the START position, adjust the power valve. Turn the valve in the clockwise direction in order to adjust the emissions level to 1 g/bhp of NOx.
After tuning the engine, verify proper operation of the NOx sensor by comparing the displayed reading to the reading on the portable measurement instrument. The slope and offset calibration adjustments are available. These adjustments are not normally required for the G3408 and G3412 engines.
Switch the air/fuel ratio control to the automatic mode in order to activate the control.
Operate the engine at various load and speed combinations in order to ensure that the air/fuel ratio control maintains the proper NOx emission levels. If necessary, adjust the offsets to the NOx target for the various inlet manifold pressures and speeds which represent the partial load points on the engine.
Ensure that the engine controller is set to the correct engine configuration. Refer to Systems Operation, "Reset to Start". Selecting the improper configuration will cause bad engine response.
Open the power valve in order to eliminate any restriction in fuel flow. Turn the valve counterclockwise by three to four turns.
Position the control valve to the START position of 350 steps for the G3412 and G3516 engines. Position the control valve to the START position of 800 steps for the G3408 engine. Ensure that the switch is in the manual mode.
Bring the engine up to rated speed and load. Do not exceed the rated load. While the AFRC is still in the START position, adjust the power valve. Turn the valve in the clockwise direction in order to adjust the emissions level to 1 g/bhp of NOx.
After tuning the engine, verify proper operation of the NOx sensor by comparing the displayed reading to the reading on the portable measurement instrument. The slope and offset calibration adjustments are available. These adjustments are not normally required for the G3408 and G3412 engines.
Switch the air/fuel ratio control to the automatic mode in order to activate the control.
Operate the engine at various load and speed combinations in order to ensure that the air/fuel ratio control maintains the proper NOx emission levels. If necessary, adjust the offsets to the NOx target for the various inlet manifold pressures and speeds which represent the partial load points on the engine.
Caterpillar parts catalog:
Parts bogie Caterpillar catalog:
D11N, D11R, D11T
D11R, D11T
D11R, D11T
D11R
D11R
D11N, D11R, D11T
D11N, D11R, D11T
D11N, D11R, D11T
D11N, D11R, D11T
D10R, D10T
D10R, D10T
D10N, D10R, D10T, D10T2, D9L
D9R, D9T
D9R, D9T
D11N, D11R, D11T
D11R
D11R
D11R, D11T
D11R, D11T