9P6834 BOGIE ASSEM. (front) Caterpillar parts
D8L
Rating:
Alternative (cross code) number:
CA9P6834
9P-6834
9P6834
CA9P6834
9P-6834
9P6834
Weight: 0.95 pounds 0 kg.
TRACK-TYPE TRACTOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$2,552.51
28 Jun 2017
BLQ: BLQ
9P6834 BOGIE A
9P6834 BOGIE A
9P6834 BOGIE A
Number on catalog scheme:
2
For full view, you need register
Compatible equipment models: 9P6834:
Information:
The Electronic Control Module (ECM) detects an abnormal fuel filter differential pressure.Use this procedure if one of the following event codes is active. Refer to Troubleshooting, "Event Codes" for information about event codes. For information on the engine monitoring system, refer to Troubleshooting, "Engine Monitoring System".Note: Some of the following codes may not be applicable for certain applications.
Table 1
Diagnostic Trouble Codes
J1939 Code CDL Code Code Description Comments
5584-15 E390 (1) Fuel Filter Restriction The code is logged.
The filter is becoming clogged. Change the filter at the next regular maintenance.
5584-16 E390 (2) Fuel Filter Restriction The code is logged.
The difference between the filtered fuel pressure and the unfiltered fuel pressure is greater than the trip point pressure.
The engine ECM will derate engine power.
Change the fuel filter.
5584-0 E390 (3) Fuel Filter Restriction The code is logged.
The difference between the filtered fuel pressure and the unfiltered fuel pressure is greater than the trip point pressure.
The engine ECM will derate engine power.
Change the fuel filter. Probable Causes
Fuel Filter
Fuel filterNote: Change the primary filter, the secondary filter, and the tertiary filter at the same time. Use clean fuel on the stud threads of filter base to reduce friction.Note: Do not fill the canister or the fuel filter before installation. The fuel can carry debris into the fuel filter and the fuel system may be damaged. The electric priming pump is designed to purge the trapped air in the new filters.
Table 2
Troubleshooting Test Steps Values Results
1. Change the fuel filters
A. Reset all active codes and clear all logged codes by cycling the keyswitch to the Off position. Change the primary fuel filter.
B. Prime the system with the electric priming pump.
C. Start the engine and allow the engine to idle for few minutes.
D. Turn the engine OFF and change the secondary fuel filter.
E. Prime the system with the electric priming pump.
F. Start the engine and allow the engine to idle for few minutes.
G. Turn the engine OFF and change the tertiary fuel filter.
H. Prime the system with the electric priming pump.
J. Restart the engine.
Fuel Filter
Result: The code is no longer active
STOP
Result: The event code becomes active after changing the fuel filters.
Repair: The problem may be electrical. Refer to Troubleshooting, "Sensor Signal (Analog, Active) - Test" for the procedure to troubleshoot the circuit.
If the procedure did not correct the issue, contact your Cat dealer Technical Communicator (TC). For further assistance, your TC can confer with the Dealer Solutions Network (DSN).
Table 1
Diagnostic Trouble Codes
J1939 Code CDL Code Code Description Comments
5584-15 E390 (1) Fuel Filter Restriction The code is logged.
The filter is becoming clogged. Change the filter at the next regular maintenance.
5584-16 E390 (2) Fuel Filter Restriction The code is logged.
The difference between the filtered fuel pressure and the unfiltered fuel pressure is greater than the trip point pressure.
The engine ECM will derate engine power.
Change the fuel filter.
5584-0 E390 (3) Fuel Filter Restriction The code is logged.
The difference between the filtered fuel pressure and the unfiltered fuel pressure is greater than the trip point pressure.
The engine ECM will derate engine power.
Change the fuel filter. Probable Causes
Fuel Filter
Fuel filterNote: Change the primary filter, the secondary filter, and the tertiary filter at the same time. Use clean fuel on the stud threads of filter base to reduce friction.Note: Do not fill the canister or the fuel filter before installation. The fuel can carry debris into the fuel filter and the fuel system may be damaged. The electric priming pump is designed to purge the trapped air in the new filters.
Table 2
Troubleshooting Test Steps Values Results
1. Change the fuel filters
A. Reset all active codes and clear all logged codes by cycling the keyswitch to the Off position. Change the primary fuel filter.
B. Prime the system with the electric priming pump.
C. Start the engine and allow the engine to idle for few minutes.
D. Turn the engine OFF and change the secondary fuel filter.
E. Prime the system with the electric priming pump.
F. Start the engine and allow the engine to idle for few minutes.
G. Turn the engine OFF and change the tertiary fuel filter.
H. Prime the system with the electric priming pump.
J. Restart the engine.
Fuel Filter
Result: The code is no longer active
STOP
Result: The event code becomes active after changing the fuel filters.
Repair: The problem may be electrical. Refer to Troubleshooting, "Sensor Signal (Analog, Active) - Test" for the procedure to troubleshoot the circuit.
If the procedure did not correct the issue, contact your Cat dealer Technical Communicator (TC). For further assistance, your TC can confer with the Dealer Solutions Network (DSN).
Caterpillar parts catalog:
Parts bogie Caterpillar catalog:
578, D8L, D8N, D8R, D8R II, D8T
D8L
D8L
D8L
7G0001
BOGIE
D10
D10
D8L