AVSPARE.COM
parts catalog

BOGIE AS-FRONT 9W7610 - Caterpillar


9W7610 BOGIE AS-FRONT Caterpillar parts D8L
Rating:
28
Alternative (cross code) number:
CA9W7610
9W-7610
9W7610
Caterpillar 9W7610 BOGIE AS-FRONT
Weight: 336 pounds 152 kg.

Buy BOGIE AS-FRONT 9W7610 Caterpillar genuine, new aftermarket tractor parts with delivery
TRACK-TYPE TRACTOR,

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below
$2,552.51
 

27 May 2017

BLQ: BLQ
9W7610 BOGIE A
Number on catalog scheme: 2
  For full view, you need register

Compatible equipment models: 9W7610:

TRACK-TYPE TRACTOR  D8L   Caterpillar

Information:


Illustration 1 g02559897
Table 1
Specification for 342-7302 Cylinder Block Gp
Item Qty Part Specification Description
1 6 248-7585 Orifice Use the following procedure to install the orifice:
Orifice (1) is only for number three cylinder through number eight cylinder.
1. Align the orifice with the outside diameter chamfer facing the cylinder block.
2. Apply green Loctite 620 to the outside diameter of the orifice.
3. Fully seat the orifice in the block flush with the head face. Remove any excessive Loctite from the head and insert face.
2 2 248-7584 Orifice Use the following procedure to install the orifice:
Orifice (2) is only for number one cylinder and for number two cylinder.
1. Align the orifice with the outside diameter chamfer facing the cylinder block.
2. Apply green Loctite 620 to the outside diameter of the orifice.
3. Fully seat the orifice in the block flush with the head face. Remove any excessive Loctite from the head and insert face.
3 1 6V-6560 O-Ring Seal Before assembly, lightly lubricate all around the bore with clean engine oil.
Illustration 2 g03356630
Front view of engine
Table 2
Item Qty Part Specification Description
A 16 371-6455 Dowel Align the cross hole of the dowel in parallel with the center line of the crankshaft. Refer to Illustration 2.
Extension of dowels from the face of the cylinder block is 7.0 0.5 mm (0.28 0.02 inch).
B 32 6V-3535 Dowel Extension of dowels from the face of the cylinder block is 16.0 1.0 mm (0.63 0.04 inch).
4 9 249-6392 Camshaft Bearing Before assembly, apply green 8T-2998 Lubricant to the inner diameter of each camshaft bearing.
The camshaft bearing joint must be in the 2 O'clock or the 10 O'clock position. The oil hole must be on the centerline of the bore.
Illustration 3 g02898357
Right side view
Table 3
Item Qty Part Specification Description
C 4 4N-0683 Dowel Extension of dowel from the face of the cylinder block is 19.0 1.0 mm (0.75 0.04 inch).
Illustration 4 g02898358
Rear view of engine
Table 4
Item Qty Part Specification Description
5 2 244-2446 Cup Plug Before assembly, apply High Strength or High Temperature Anaerobic Flange Sealant to the outside diameter and to the bores of cup plugs.
6 26 262-1102 Cup Plug Before assembly, apply High Strength or High Temperature Anaerobic Flange Sealant to the outside diameter and to the bores of cup plugs.
Installation depth is 3.4 1.8 mm (0.13 0.07 inch).
D - - Bore in the block for the camshaft bearing is 98.00 0.02 mm (3.858 0.001 inch).
F - - New dimension from centerline of crankshaft bearing bore to the top of the block is 650 mm (25.6 inch).
7

Caterpillar parts catalog:

Caterpillar parts catalog
D8L TRACTOR 53Y00001-UP (MACHINE) POWERED BY 3408 ENGINE


Parts bogie Caterpillar catalog:

7T8555 BOGIE-MINOR
578, D8L, D8N, D8R, D8R II, D8T
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.