AVSPARE.COM
parts catalog

BOLT 0 - Caterpillar



0 BOLT Caterpillar parts BOLT
Rating:
61
Alternative (cross code) number:
CA0
-0
0
Caterpillar 0 BOLT

Buy BOLT 0 Caterpillar genuine, new aftermarket tractor parts with delivery

Cross Reference:

CATERPILLAR 0, MECAFILTER FA3605,
Number on catalog scheme:
 
  For full view, you need register

Information:

GRADERS
120H (2AN, 3GR, 4MK, 5FM, 6NM, 6TM, 9FN, 9YR),
135H (3YK, 7MM, 8WN),
12H (2GS, 2LR, 2WR, 4ER, 4XM, 5ZM, 8MN),
140H (2ZK, 3AS, 3FR, 5HM, 8JM, 8KM, 9TN, 9ZN),
143H (1AL),
160H (2HS, 2FM, 3GM, 3HR, 6WM, 9EJ, 9JM),
163H (5AK) MOTOR GRADERSProblem:
Problems have been reported of difficulty in troubleshooting manual modulation problems on the above motor graders. The 111-7088 Pressure Switch is an important component to consider, but there is a lack of troubleshooting information on this switch. Also, the set points sometimes vary from the specification.Solution:
The following brief explanation provides a procedure to troubleshoot the 111-7088 Pressure Switch, which is used to communicate to the ECM when the manual modulation pedal is being used. When the pedal is depressed, the pressure switch opens and the ECM logic determines the correct OFF/ON directional clutch solenoid positions. During a speed change, the ECM determines transmission oil temperature and will switch the directional clutch solenoid to the OFF position when the oil is cold (less than 0 deg C or 32 deg F). The solenoid is left ON with warmer oil. During a directional shift, the ECM will turn the directional clutch solenoid to OFF and leave the range and speed clutch solenoids ON. Once the operator starts raising the modulation pedal, the pressure switch will close at 75 Kpa (11 psi). Once closed, the ECM completes the shift sequence by switching the proper clutch solenoids ON or OFF. If the pressure switch fails, the ECM shift sequence may not begin at the proper time and clutch modulation will be affected.The easiest method to troubleshoot the pressure switch is to disconnect the machine wiring harness from the switch. Jumper the two wires in the harness together using a 4E-2898 Plug Assembly or like jumper wire. Operate the machine to determine if the modulation problem remains. If there isn't a modulation problem, the 111-7088 Pressure Switch has failed and should be replaced. If the modulation problem remains, the problem is not in the pressure switch. Remove the jumper wire and connect the harness back to the pressure switch. The problem will be either cable adjustment or the modulation spool in the transmission hydraulic control valve.COPYRIGHT 1998 CATERPILLAR ALL RIGHTS RESERVED

Caterpillar parts catalog:

Caterpillar parts catalog
D8 TRACTOR / POWER SHIFT / 46A03044-10724 (MACHINE)


Parts bolt Caterpillar catalog:

2909407 BOLT
Caterpillar
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.