0969259 BOLT Caterpillar parts
14M, 16M, 301.5, 302.5, 303.5, 304.5, 3116, 320 L, 320B, 322, 322 LN, 322C, 322C FM, 324D, 324D FM, 324D FM LL, 324D L, 324D LN, 325C, 325C FM, 325D, 325D FM, 325D FM LL, 325D L, 325D MH, 326D L, 328D...
Rating:
Alternative (cross code) number:
CA0969259
096-9259
0969259
CA0969259
096-9259
0969259
Weight: 0.20 pounds 0 kg.
Information:
COATING/PLATING
Zinc-Dichromate Coating
GRIP LENGTH
26
mm
HEAD HEIGHT
9.09
mm
HEX SIZE
21
mm
LENGTH
60
mm
MATERIAL
Steel - 1040 MPa Min Tensile Strength
THREAD SIZE
M14X2
EXCAVATOR, WHEELED EXCAVATOR,
Compatible equipment models: 0969259:
Number on catalog scheme:
2
For full view, you need register
Information:
Do not overtighten the tracks. Tracks that are too tight can cause premature failure of the tracks. Tracks that are too tight can cause power loss and bearing failures.Tracks that are too loose increase the possibility of the track derailing or the drive lugs mis-feeding on the drive sprocket. In aggressive operating conditions, occasional mis-feeding is normal. If consistent mis-feeding is observed, ensure that the track tension is set to the recommended specification. If the track tension is set to the recommended specification and mis-feeding is still observed, then your application may require a tighter track tension. Increase the track tension until consistent mis-feeding is no longer observed.The intervals for track tension vary depending on the following conditions: the machine application, the operator, the soil conditions, the climate and the condition of the undercarriage components. Operators are responsible for basic visual inspections of the track tension on a daily basis.
Inspect
Illustration 1 g01450469Support the machine so that the track is a minimum of 51 mm (2 inch) above the ground.
Illustration 2 g01450565Measure the track sag at the middle track roller. Measure the distance from the bottom surface of the flange on the roller to the inside top surface of the track. Refer to the table for the proper specifications for your model.Note: Machines equipped with four track rollers, measure the track sag at the second or third track roller.
Table 1
Track Sag Specifications
239D and 249D 259D 279D and 289D 299D/D2 and 299D/D2 XHP
Minimum Sag 15 mm (0.59 inch) 15 mm (0.59 inch) 25 mm (0.98 inch) 25 mm (0.98 inch)
Maximum Sag 25 mm (0.98 inch) 25 mm (0.98 inch) 35 mm (1.378 inch) 35 mm (1.378 inch) Track Adjustment
Illustration 3 g01450599
To adjust the track, remove the access panel on the side of the undercarriage.
Illustration 4 g01450604
Pressurized grease in a cylinder is used to provide tension on the track. Use a grease gun in order to apply grease to the grease fitting on the cylinder. The track will be tightened.
Recheck the track tension.
Replace the access panel when the desired sag is achieved.Detension the track
Personal injury or death can result from grease under pressure.Grease coming out of the relief valve under pressure can penetrate the body causing injury or death.Do not stand directly in front of the relief valve to see if grease is escaping. Watch the track or track adjustment cylinder to see if the track is being loosened.If track does not loosen, close the relief valve and consult your Cat dealer.
Note: Many operations for maintenance of the undercarriage require the track to be loosened.
To detension the track, remove the access panel on the side of the undercarriage.
Loosen the grease fitting with a suitable device. Loosen the grease fitting carefully until the track begins to loosen.Note: Catch the grease in a suitable container. Dispose of the grease in accordance with all applicable regulations.Note: One turn should be sufficient. If grease does not flow as expected, the lock plate can be temporarily removed. The relief valve can be
Cat SIS web machinery list:
Parts bolt Caterpillar catalog:
320B FM LL, 322B L, 325B L, 325C, 330B L, 330D MH, 345B II, 345C, 345C L, 345C MH, 365B, 365B II, 365B L, 365C, 365C L, 365C L MH, 374D L, 374F L, 375, 375 L, 385B, 385C, 385C FS, 385C L, 385C L MH, 3...
2384C, 2484C, 322 FM L, 322B L, 322C, 322C FM, 324D FM, 324D FM LL, 324D L, 330, 330 FM L, 330B L, 330C, 330C FM, 330C L, 330C MH, 330D, 330D FM, 330D L, 330D MH, 336D L, 336E L, 345B, 345B II, 345B I...
325D FM, 325D FM LL, 330D FM, 330D L, 330D MH, 345B II, 345C, 345C L, 345C MH, 345D, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L, 349E L HVG, 349E L VG, 349F L, 365C L, 551, 552, 552 2, 568 FM LL
320C FM, 320D, 320D FM, 320D FM RR, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 323E L, 324E, 324E L, 324E LN, 329D L, 329E, 329E L, 336E, 336E H, 336E HVG, 336E L, 336E LH, 336E LN, 336F L, 345D L, 349...
324D, 324D L, 324D LN, 324E, 324E L, 324E LN, 325D, 325D L, 326D L, 329D, 329D L, 329D LN, 329E, 329E L, 329E LN, 330C, 330C L, 330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 3...
320B, 320C, 320D, 320D FM, 320D L, 320D2, 320D2 L, 320E, 320E LN, 321C, 322C, 322C FM, 323D L, 323D LN, 323D SA, 323D2 L, 323E L, 324D, 324D FM, 324D L, 324D LN, 324E, 324E L, 324E LN, 325C, 325C FM, ...
320C, 320C FM, 320D, 320D FM, 320D FM RR, 322C, 322C FM, 323D LN, 323D SA, 323E L, 324D, 324D L, 324D LN, 324E, 324E L, 324E LN, 325C, 325C FM, 325D, 325D L, 325D MH, 326D L, 329D, 329D L, 329D LN, 32...
325C, 330, 330 FM L, 330B L, 330C L, 330D, 330D L, 336D L, 345B, 345C, 345C L, 345D, 349D L, 350, 350 L, OEMS, TK1051
16M, 320D, 320D FM, 320D L, 320D2, 320D2 L, 320E, 320E LN, 322C, 323D L, 323D LN, 323D SA, 323D2 L, 323E L, 325C, 325D, 325D FM, 325D L, 328D LCR, 329D, 329D L, 329D LN, 329E, 329E L, 329E LN, 330C, 3...
320C, 325C, 330B L, 330C, 330C FM, 330C L, 330C MH, 330D, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 336E, 336E H, 336E HVG, 336E L, 336E LH, 336E LN, 336F L, 340D L, 340D2 L, 34...
1090, 2290, 320D, 320D FM, 322C FM, 324D FM, 324D FM LL, 325C, 325D, 325D L, 329D, 329D L, 329D LN, 329E, 329E L, 329E LN, 336E, 345C, 511, OEMS, TK711
320E LRR, 320E RR, 323E L, 325D L, 328D LCR, 329D, 329D L, 329E, 329E L, 349D, 374D L, 374F L, 390D, 390D L, 390F L
6C2206
BOLT
3306B
3306B
1A4399
BOLT
1673
1673
3H0368
BOLT (1.375" Long)
1673, 666
1673, 666
1673, 621H, 621K, 623H, 623K, 623K LRC, 627H, 627K, 627K LRC, 641B, 651, 651B, 657B, 666
6L8535
BOLT
1673, 615, 615C, 621, 623B, 623E, 623F, 623G, 623H, 633E
1673, 615, 615C, 621, 623B, 623E, 623F, 623G, 623H, 633E
4B4532
BOLT
1673, 173B, 183B, 966F II, 970F, IT38F, IT38G
1673, 173B, 183B, 966F II, 970F, IT38F, IT38G
1427396
BOLT
3054, 3054B
3054, 3054B
7C3153
BOLT
3054, AP-800, CP-433B, CS-323
3054, AP-800, CP-433B, CS-323
7C3152
BOLT
3054, AP-800, CP-433B, CS-323
3054, AP-800, CP-433B, CS-323
0320680
BOLT-12 POINT HEAD
231D, 235D, 973, G3406
231D, 235D, 973, G3406
0964034
BOLT-WING
303.5E, 304E, 305.5, 305.5E, 305E, 306E, 307, 307B, 307C, 307D, 307E, 308C, 308D, 308E, 308E2 CR, 311, 3116, 311B, 311C, 311F LRR, 312, 312B, 312C, 312C L, 313B, 314C, 315, 315B, 315B FM L, 315C, 317B...
303.5E, 304E, 305.5, 305.5E, 305E, 306E, 307, 307B, 307C, 307D, 307E, 308C, 308D, 308E, 308E2 CR, 311, 3116, 311B, 311C, 311F LRR, 312, 312B, 312C, 312C L, 313B, 314C, 315, 315B, 315B FM L, 315C, 317B...
3116, 315, 317, 320 L, 325B L, 330B L, 550, 550B, 560B, 570, 570B, 580, 580B, SW345B, SW60