1438431 BOLT Caterpillar parts
3618, 824K, 825K, 826K, 834K, 836K, 988K
Rating:
Alternative (cross code) number:
CA1438431
143-8431
1438431
CA1438431
143-8431
1438431
Weight: 0.27 pounds 0 kg.
Information:
GRIP LENGTH
22
mm
HEAD HEIGHT
10.32
mm
HEX SIZE
24
mm
LENGTH
60
mm
MATERIAL
Stainless Steel Tensile Strength Min 895 MPa
THREAD SIZE
M16X2
LANDFILL COMPACTOR, WHEEL LOADER,
Compatible equipment models: 1438431:
Number on catalog scheme:
11
For full view, you need register
Information:
Removal Procedure
Start By:
Remove covers. Refer to Disassembly and Assembly, "Covers - Remove and Install" for the machine that is being serviced.Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the component should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism.Note: Put identification marks on all lines, on all hoses, on all wires, and on all tubes for installation purposes. Plug all lines, hoses, and tubes. This helps to prevent fluid loss and this helps to keep contaminants from entering the system.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Personal injury can result from hydraulic oil pressure and hot oil.Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system.Make sure all of the attachments have been lowered, oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.
Drain the hydraulic oil into a suitable container for storage or disposal.
Illustration 1 g00559148
Disconnect hose assembly (1) and hose assembly (2) .
Remove two bolts (3). Disconnect tube assembly (4) .
Illustration 2 g00559149
Remove the four bolts and washers (5). Disconnect tube assembly (6) .
Illustration 3 g00559150
Note: Rotate tube (7) clockwise and disconnect tube (7) from the junction box.
Remove the two bolts and washers (8). Remove tube assembly (7) .
Disconnect tube assembly (9) .
Illustration 4 g00559152
Remove tube (4) .
Illustration 5 g00559155
Remove tube (13) .
Disconnect wiring harness (14) .
Remove two bolts (11) and implement pump (12) .
Illustration 6 g00559157
Remove the four allen head screw (15). Remove junction box (16) .
Illustration 7 g00559158
Remove four bolts (17) and connector (18) .
Illustration 8 g00559159
Remove O-ring seal (19) on implement pump (12) .
Start By:
Remove covers. Refer to Disassembly and Assembly, "Covers - Remove and Install" for the machine that is being serviced.Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the component should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism.Note: Put identification marks on all lines, on all hoses, on all wires, and on all tubes for installation purposes. Plug all lines, hoses, and tubes. This helps to prevent fluid loss and this helps to keep contaminants from entering the system.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Personal injury can result from hydraulic oil pressure and hot oil.Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system.Make sure all of the attachments have been lowered, oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.
Drain the hydraulic oil into a suitable container for storage or disposal.
Illustration 1 g00559148
Disconnect hose assembly (1) and hose assembly (2) .
Remove two bolts (3). Disconnect tube assembly (4) .
Illustration 2 g00559149
Remove the four bolts and washers (5). Disconnect tube assembly (6) .
Illustration 3 g00559150
Note: Rotate tube (7) clockwise and disconnect tube (7) from the junction box.
Remove the two bolts and washers (8). Remove tube assembly (7) .
Disconnect tube assembly (9) .
Illustration 4 g00559152
Remove tube (4) .
Illustration 5 g00559155
Remove tube (13) .
Disconnect wiring harness (14) .
Remove two bolts (11) and implement pump (12) .
Illustration 6 g00559157
Remove the four allen head screw (15). Remove junction box (16) .
Illustration 7 g00559158
Remove four bolts (17) and connector (18) .
Illustration 8 g00559159
Remove O-ring seal (19) on implement pump (12) .
Caterpillar parts catalog:
Parts bolt Caterpillar catalog:
231D, 235D, 30/30, 3406E, 3608, 3618, 517, 518, 527, 528, 528B, 530B, 583T, 611, 613C, 613C II, 613G, 615, 615C, 623B, 633D, 725, 725C, 730, 730C, 735, 735B, 740, 740B, 773G, 773G LRC, 773G OEM, 775G,...
1800155
BOLT
3618
3618
16, 1693, 235, 245, 3606, 3608, 3612, 3616, 3618, 627, 631C, 657B, 657E, 666, 69D, 7261, 768B, 769, 769C, 769D, 771C, 771D, 772, 773B, 773D, 773E, 775B, 775D, 775E, 824B, 825B, 826B, 834, 977L, 980, 9...
140, 141, 30/30, 3192, 319D L, 319D LN, 320D, 320D GC, 320D L, 320D LRR, 320D RR, 320D2, 320E, 320E L, 320E LN, 320E LRR, 321D LCR, 323D L, 323D LN, 323D SA, 323E L, 324D, 324D L, 324E, 324E L, 324E L...
3618, 561C, 58, 69D, 769D, 771D, 773D, 773E, 775D, 775E, 776C, 776D, 777, 777B, 777D, 939, 939C, 941, 955K, 966C, 977K, C18, D4D, D5C, D5C III, D6C
1858882
BOLT
3606, 3608, 3612, 3616, 3618
3606, 3608, 3612, 3616, 3618
6S7567
BOLT
3618, CS-643
3618, CS-643
1526979
BOLT
3618
3618
1462762
BOLT
3618
3618
120, 120B, 120G, 120H, 120H ES, 120H NA, 12E, 12H, 12H ES, 12H NA, 135H, 135H NA, 140, 140H, 140H ES, 140H NA, 140K, 140M, 143H, 14G, 14H, 16, 160H, 160H ES, 160H NA, 160K, 160M, 163H, 163H NA, 16H, 2...
1440752
BOLT-HIGH TEMPERATURE
3616, 3618
3616, 3618