1691637 BOLT Caterpillar parts
424B, 424B HD, 908, CP-433E, CP-44, CP-573E, CP-64, CP-663E, CP-68B, CP-74B, CP-76, CS-423E, CS-433E, CS-44, CS-56B, CS-64, CS-663E, CS-683E, CS-68B, CS-74, CS-74B, CS-76B, CS-78B
Rating:
Alternative (cross code) number:
CA1691637
169-1637
1691637
CA1691637
169-1637
1691637
Weight: 0.21 pounds 0 kg.
Information:
COATING/PLATING
Phosphate and Oil Coating
GRIP LENGTH
31
mm
HEAD HEIGHT
9.09
mm
HEX SIZE
22
mm
LENGTH
65
mm
MATERIAL
Steel - 1040 MPa Min Tensile Strength
THREAD SIZE
M14X1.5
BACKHOE LOADER, VIBRATORY COMPACTOR,
Compatible equipment models: 1691637:
Number on catalog scheme:
2
For full view, you need register
Information:
Installation Procedure
Table 1
Tool Part Number Part Description Qty
A - Plastigage -
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Install the connecting rod bearings dry when the clearance checks are made. Put clean engine oil on the connecting rod bearings for final assembly.
Install the upper half of the connecting rod bearing in the connecting rod.
Install the lower half of the connecting rod bearing in the connecting rod.Note: Align the tabs on the back of the connecting rod bearings with the tab grooves in the connecting rod.
Illustration 1 g00487493
In order to check the connecting rod bearing clearance, put Tool (A) on the connecting rod bearing, as shown.
Put clean engine oil (SAE 30) on the connecting rod bolts.
When the connecting rod caps are installed, ensure that the identification marks are aligned.
Illustration 2 g00487412
Note: Do not turn the crankshaft when Tool (A) is positioned.
Ensure that connecting rod (3) is in position on the crankshaft. Install connecting rod cap (2) and connecting rod nuts (1) on connecting rod (3) .
Illustration 3 g00287852
Tighten the connecting rod nuts to a torque of 40 4 N m (30 3 lb ft). Mark the position of the nuts. Tighten each nut for an additional 90 degrees (1/4 turn).
Remove the connecting rod cap. Measure Tool (A) on the bearing surface before Tool (A) is removed. The clearance between the connecting rod bearing and a new crankshaft should be 0.076 to 0.168 mm (.0025 to .0066 inch). The clearance between the connecting rod bearing and a used crankshaft should be 0.25 mm (0.01 inch).
Install connecting rod cap (2) and connecting rod nuts (1) on connecting rod (3). Repeat Step 6 in order to tighten the nuts.
Repeat Steps 1 through 8 for the remaining connecting rod bearings.End By:
Install the oil pan plate. Refer to Disassembly and Assembly, "Engine Oil Pan Plate - Remove and Install".
Install the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Install".
Table 1
Tool Part Number Part Description Qty
A - Plastigage -
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Install the connecting rod bearings dry when the clearance checks are made. Put clean engine oil on the connecting rod bearings for final assembly.
Install the upper half of the connecting rod bearing in the connecting rod.
Install the lower half of the connecting rod bearing in the connecting rod.Note: Align the tabs on the back of the connecting rod bearings with the tab grooves in the connecting rod.
Illustration 1 g00487493
In order to check the connecting rod bearing clearance, put Tool (A) on the connecting rod bearing, as shown.
Put clean engine oil (SAE 30) on the connecting rod bolts.
When the connecting rod caps are installed, ensure that the identification marks are aligned.
Illustration 2 g00487412
Note: Do not turn the crankshaft when Tool (A) is positioned.
Ensure that connecting rod (3) is in position on the crankshaft. Install connecting rod cap (2) and connecting rod nuts (1) on connecting rod (3) .
Illustration 3 g00287852
Tighten the connecting rod nuts to a torque of 40 4 N m (30 3 lb ft). Mark the position of the nuts. Tighten each nut for an additional 90 degrees (1/4 turn).
Remove the connecting rod cap. Measure Tool (A) on the bearing surface before Tool (A) is removed. The clearance between the connecting rod bearing and a new crankshaft should be 0.076 to 0.168 mm (.0025 to .0066 inch). The clearance between the connecting rod bearing and a used crankshaft should be 0.25 mm (0.01 inch).
Install connecting rod cap (2) and connecting rod nuts (1) on connecting rod (3). Repeat Step 6 in order to tighten the nuts.
Repeat Steps 1 through 8 for the remaining connecting rod bearings.End By:
Install the oil pan plate. Refer to Disassembly and Assembly, "Engine Oil Pan Plate - Remove and Install".
Install the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Install".
Cat SIS web machinery list:
Parts bolt Caterpillar catalog:
120M, 120M 2, 12M, 12M 2, 12M 3, 12M 3 AWD, 140M, 140M 2, 140M 3, 140M 3 AWD, 14M, 160M, 160M 2, 160M 3, 160M 3 AWD, 16M, 30/30, 517, 527, 583T, 587R, 587T, 613G, 621H, 621K, 623H, 623K, 623K LRC, 627...
1090, 115, 1190, 1190T, 1290T, 1390, 206, 212, 2290, 229D, 2390, 2391, 2491, 2590, 311, 311B, 311C, 311D LRR, 311F LRR, 312, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313D, 3...
301.4C, 303.5D, 304D CR, 311, 311B, 312B, 312E, 313B, 316E L, 3176B, 320E LN, 323E L, 328D LCR, 365B, 365B L, 365C, 365C L, 365C L MH, 374D L, 374F L, 385B, 385C, 385C FS, 385C L, 385C L MH, 390D, 390...
120B, 140B, 307, 312, 315, 317, 325 LN, 330, 350, 375, 375 L, 5080, 902, 906, 906H, 906H2, 907H, 907H2, 908, 908H, 908H2, 910K, 914G, 914K, 924G, 924GZ, 924H, 924HZ, 924K, 928H, 928HZ, 930G, 930K, 938...
1090, 115, 1190, 1190T, 1290T, 1390, 2290, 2384C, 2390, 2391, 2491, 2590, 312D, 323D L, 325C, 325D, 325D L, 328D LCR, 329D L, 330, 330 FM L, 330 L, 330B, 330B L, 330C, 330C FM, 330C L, 330C MH, 330D, ...
824K, 825G, 825G II, 825H, 825K, 826K, 836G, 836H, 962G, 966F, 966F II, 966G, 970F, 972G, 980H, 990 II, CP-433E, CP-44, CP-533E, CP-56, CP-573E, CP-64, CP-663E, CP-76, CS-423E, CS-433E, CS-44, CS-533E...
1390, 231D, 2590, 318C, 319C, 320C, 321C, 322B L, 322C, 323D L, 324D LN, 325B L, 325C, 325D, 325D L, 330, 330B L, 330C, 330C L, 330D L, 330D LN, 336D L, 345C, 345C L, 350, 350 L, 365B, 365B II, 365C, ...
2470C, 2570C, 2670C, 2864C, 328D LCR, 375, 375 L, 385B, 385C, 385C L, 390D, 390D L, 390F L, 5080, 5230, 5230B, 553C, 563C, 573C, 586C, 623H, 623K, 623K LRC, 63, 725, 730, 735, 740, 740B, 793F, 793F AC...
206, 225, 814F, 814F II, 815F, 815F II, 816F, 816F II, 902, 906, 908, 914G, 924F, 924G, 924GZ, 928G, 938F, 938G, 938G II, 938H, 950F II, 950G, 950G II, 960F, 962G, 962G II, 966F II, 966G, 966G II, 966...
784C, 785, 785C, 785D, 789B, 793, 793B, 793C, 844, 844H, 844K, 953C, 966F, 980C, CP-68B, CP-74B, CS-56B, CS-66B, CS-68B, CS-74B, D8L, D9N
10-20B, 12M 2, 140M, 160M, 515, 525, 587T, AP-1055D, AS3251C, AS3301C, BG-2455D, BG-260D, CB-614, CP-433C, CP-433E, CP-44, CP-56, CP-563, CP-573E, CP-64, CP-68B, CP-74B, CS-323C, CS-433C, CS-433E, CS-...
902, 906, 908, R1300
140, 16, 1673, 1693, 206, 212, 214, 224, 225, 235, 3181, 3406, 3406C, 3408, 3408B, 3408C, 3412, 3412C, 3512, 3512B, 3512C, 3606, 3608, 3612, 3616, 3618, 416, 424B, 424B HD, 426, 428, 613C, 615, 615C, ...
236D, 242D, 246D, 303.5E, 303E CR, 304E, 305.5, 305.5E, 305E, 307, 307B, 307C, 308C, 308E, 308E CR, 308E SR, 311, 311B, 311F LRR, 312, 312B, 312B L, 315, 315B, 315B FM L, 315B L, 317, 317B LN, 318B, 3...
216B3, 226B3, 236D, 242D, 257D, 259D, 311F LRR, 320 L, 320D, 320D L, 320D LRR, 320D RR, 321D LCR, 322B L, 322B LN, 323D L, 325 LN, 325B L, 328D LCR, 330B L, 330D, 330D FM, 330D L, 330D LN, 330D MH, 33...
3759417
BOLT-TRACK
289C, 299C, 299D, 299D XHP
289C, 299C, 299D, 299D XHP
3759416
BOLT-TRACK
289C, 299C, 299D, 299D XHP
289C, 299C, 299D, 299D XHP
10 FT, 10B, 120H, 120H ES, 120H NA, 120M, 12G, 12H, 12H ES, 12H NA, 12M, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140M, 143H, 14H, 14H NA, 14M, 160H, 160H ES, 160H NA, 160M, 163H, 163H NA, 2...
120H, 12H, 135H, 140H, 143H, 160H, 163H, 312C, 325C, 345C, 345C L, 375, 375 L, 424B, 424B HD, 5130, 584, 623E, 623F, 623G, 950G, 950G II, 962G, 962G II, 992G, 992K, AP-1000B, AP-1055B, AP-650B, BG-225...
2949800
BOLT
424B, 424B HD
424B, 424B HD
2235550
BOLT
424B, 424B HD, CP-433E, CP-44, CS-423E, CS-433E, CS-44
424B, 424B HD, CP-433E, CP-44, CS-423E, CS-433E, CS-44
3318531
BOLT-SPECIAL
424B, 424B HD
424B, 424B HD
3311700
BOLT
424B, 424B HD
424B, 424B HD
416F, 420F, 424B, 424B HD, 428F, 430F, 432F, 434F, 444F, 450F, 525D, 535D, 545D, 555D, 924G, 924GZ, 924H, 924HZ, 928G, 928H, 928HZ, 930G, C4.4, C4.4XQ100, C4.4XQ80, C7.1, CB-44B, CB-54B, CP-54B, CP-68...