1798733 BOLT Caterpillar parts
320C, 320C FM, 320D, 320D FM, 320D FM RR, 322C, 322C FM, 323D LN, 323D SA, 323E L, 324D, 324D L, 324D LN, 324E, 324E L, 324E LN, 325C, 325C FM, 325D, 325D L, 325D MH, 326D L, 329D, 329D L, 329D LN, 32...
Rating:
Alternative (cross code) number:
CA1798733
179-8733
1798733
CA1798733
179-8733
1798733
Weight: 0.99 pounds 0 kg.
Information:
COATING/PLATING
Phosphate and Oil Coating
GRIP LENGTH
118
mm
HEAD HEIGHT
12.88
mm
HEX SIZE
30
mm
LENGTH
170
mm
MATERIAL
Steel 1170 MPa Min Tensile Strength
THREAD SIZE
M20X2.5
EXCAVATOR, UNDERCARRIAGE,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$21.49
24 Mar 2019
REPLACEMENT CATERPILLAR: REPLACEMENT CAT
CATERPILLAR 1798733 BOLT-HEX H NEW
Number on catalog scheme:
4
For full view, you need register
Compatible equipment models: 1798733:
Information:
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0074 Slide Hammer Puller 1
8B-7557 Adapter 1
B 1P-0520 Driver Group 1
C 138-7575 Link Bracket 2 Start By:
Remove the engine oil filter housing. Refer to Disassembly and Assembly, "Engine Oil Filter Housing - Remove".
Remove the crankshaft front seal and the wear sleeve. Refer to Disassembly and Assembly, "Crankshaft Front Seal and Wear Sleeve - Remove".
Remove accessory drive (front). Refer to Disassembly and Assembly, "Accessory Drive (Front) - Remove".
Remove the engine oil and water pump drive. Refer to Disassembly and Assembly, "Engine Oil and Water Pump Drive - Remove".
Remove the auxiliary water pump. Refer to Disassembly and Assembly, "Auxiliary Water Pump - Remove".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01255428
Remove the clips from front drive housing (3) .
Attach Tooling (C) and a suitable lifting device to mounting bracket (1). The weight of mounting bracket (1) is approximately 70 kg (154 lb).
Remove bolts (2) and mounting bracket (1) .
Illustration 2 g01255435
Remove elbow (5) and tube (4) .
Remove cover (6) and the O-ring seal from front drive housing (3) .
Remove the bolts from the end of shaft (8). Use Tooling (A) to remove shaft (8) and idler gear (7) from both sides of the engine.
Use Tooling (B) and a suitable press to remove the bearing from idler gear (7) .
Illustration 3 g01255488
Remove washers (10) from front drive housing (3) .
Attach Tooling (C) and a suitable lifting device to front drive housing (3). The weight of front drive housing (3) is approximately 200 kg (450 lb).
Remove the bolts that hold the engine oil pan to front drive housing (3). Remove bolts (9), front drive housing (3), and the front drive housing gasket.Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
B 1P-0520 Driver Group 1
C 138-7575 Link Bracket 2
D - Guide Bolt
5/8 - 11 NC by 8 inch 2
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 4 g01255488
Install the front drive housing gasket on the cylinder block. Install Tooling (D) in the cylinder block.
Attach Tooling (C) and a suitable lifting device to front drive housing (3). The weight of front drive housing (3) is approximately 200 kg (450 lb). Position front drive housing (3) on Tooling (D) .
Install bolts (9) in front drive housing (3) and tighten the bolts evenly. Cut the excess front drive housing gasket at the face of the cylinder block.
Inspect the condition of the gasket on the engine oil pan. Replace the gasket, if necessary. Install the bolts that attach the engine oil pan to front drive housing (3) .
Install washers (10) in front drive housing (3) .
Illustration 5 g01255435
Use Tooling (B) to install
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0074 Slide Hammer Puller 1
8B-7557 Adapter 1
B 1P-0520 Driver Group 1
C 138-7575 Link Bracket 2 Start By:
Remove the engine oil filter housing. Refer to Disassembly and Assembly, "Engine Oil Filter Housing - Remove".
Remove the crankshaft front seal and the wear sleeve. Refer to Disassembly and Assembly, "Crankshaft Front Seal and Wear Sleeve - Remove".
Remove accessory drive (front). Refer to Disassembly and Assembly, "Accessory Drive (Front) - Remove".
Remove the engine oil and water pump drive. Refer to Disassembly and Assembly, "Engine Oil and Water Pump Drive - Remove".
Remove the auxiliary water pump. Refer to Disassembly and Assembly, "Auxiliary Water Pump - Remove".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01255428
Remove the clips from front drive housing (3) .
Attach Tooling (C) and a suitable lifting device to mounting bracket (1). The weight of mounting bracket (1) is approximately 70 kg (154 lb).
Remove bolts (2) and mounting bracket (1) .
Illustration 2 g01255435
Remove elbow (5) and tube (4) .
Remove cover (6) and the O-ring seal from front drive housing (3) .
Remove the bolts from the end of shaft (8). Use Tooling (A) to remove shaft (8) and idler gear (7) from both sides of the engine.
Use Tooling (B) and a suitable press to remove the bearing from idler gear (7) .
Illustration 3 g01255488
Remove washers (10) from front drive housing (3) .
Attach Tooling (C) and a suitable lifting device to front drive housing (3). The weight of front drive housing (3) is approximately 200 kg (450 lb).
Remove the bolts that hold the engine oil pan to front drive housing (3). Remove bolts (9), front drive housing (3), and the front drive housing gasket.Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
B 1P-0520 Driver Group 1
C 138-7575 Link Bracket 2
D - Guide Bolt
5/8 - 11 NC by 8 inch 2
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 4 g01255488
Install the front drive housing gasket on the cylinder block. Install Tooling (D) in the cylinder block.
Attach Tooling (C) and a suitable lifting device to front drive housing (3). The weight of front drive housing (3) is approximately 200 kg (450 lb). Position front drive housing (3) on Tooling (D) .
Install bolts (9) in front drive housing (3) and tighten the bolts evenly. Cut the excess front drive housing gasket at the face of the cylinder block.
Inspect the condition of the gasket on the engine oil pan. Replace the gasket, if necessary. Install the bolts that attach the engine oil pan to front drive housing (3) .
Install washers (10) in front drive housing (3) .
Illustration 5 g01255435
Use Tooling (B) to install
Cat SIS web machinery list:
Parts bolt Caterpillar catalog:
320B FM LL, 322B L, 325B L, 325C, 330B L, 330D MH, 345B II, 345C, 345C L, 345C MH, 365B, 365B II, 365B L, 365C, 365C L, 365C L MH, 374D L, 374F L, 375, 375 L, 385B, 385C, 385C FS, 385C L, 385C L MH, 3...
2384C, 2484C, 322 FM L, 322B L, 322C, 322C FM, 324D FM, 324D FM LL, 324D L, 330, 330 FM L, 330B L, 330C, 330C FM, 330C L, 330C MH, 330D, 330D FM, 330D L, 330D MH, 336D L, 336E L, 345B, 345B II, 345B I...
320C FM, 320D, 320D FM, 320D FM RR, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 323E L, 324E, 324E L, 324E LN, 329D L, 329E, 329E L, 336E, 336E H, 336E HVG, 336E L, 336E LH, 336E LN, 336F L, 345D L, 349...
324D, 324D L, 324D LN, 324E, 324E L, 324E LN, 325D, 325D L, 326D L, 329D, 329D L, 329D LN, 329E, 329E L, 329E LN, 330C, 330C L, 330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 3...
320B, 320C, 320D, 320D FM, 320D L, 320D2, 320D2 L, 320E, 320E LN, 321C, 322C, 322C FM, 323D L, 323D LN, 323D SA, 323D2 L, 323E L, 324D, 324D FM, 324D L, 324D LN, 324E, 324E L, 324E LN, 325C, 325C FM, ...
325C, 330, 330 FM L, 330B L, 330C L, 330D, 330D L, 336D L, 345B, 345C, 345C L, 345D, 349D L, 350, 350 L, OEMS, TK1051
16M, 320D, 320D FM, 320D L, 320D2, 320D2 L, 320E, 320E LN, 322C, 323D L, 323D LN, 323D SA, 323D2 L, 323E L, 325C, 325D, 325D FM, 325D L, 328D LCR, 329D, 329D L, 329D LN, 329E, 329E L, 329E LN, 330C, 3...
320C, 325C, 330B L, 330C, 330C FM, 330C L, 330C MH, 330D, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 336E, 336E H, 336E HVG, 336E L, 336E LH, 336E LN, 336F L, 340D L, 340D2 L, 34...
320C, 320C FM, 320C L, 320D, 320D FM, 320D GC, 320D L, 320D LRR, 320D RR, 321C, 321D LCR, 323D L
1090, 2290, 320D, 320D FM, 322C FM, 324D FM, 324D FM LL, 325C, 325D, 325D L, 329D, 329D L, 329D LN, 329E, 329E L, 329E LN, 336E, 345C, 511, OEMS, TK711
320E LRR, 320E RR, 323E L, 325D L, 328D LCR, 329D, 329D L, 329E, 329E L, 349D, 374D L, 374F L, 390D, 390D L, 390F L
325C, 330C L, 330D L
2128611
BOLT
320C
320C
1700908
BOLT
574, 574B
574, 574B
2208761
BOLT
564, 574, 574B
564, 574, 574B
1835937
BOLT
574
574
1705577
BOLT
574, 574B
574, 574B
1705524
BOLT
574, 574B
574, 574B
2870190
BOLT
320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LRR, 320D RR, 323D L, 323D LN
320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LRR, 320D RR, 323D L, 323D LN
1795091
BOLT
320C, 322C
320C, 322C
9T8052
BOLT
14G, 14H, 14H NA, 14M, 16G, 16H, 16H NA, 16M, 320C, 325B L, 325D L, 330C, 345B II, CTV40, G315B, G320, G325B, MP15, MP318, P360, S305, S365B, S365C, VHC-30, VHS-50, VHS-60/3, VHS-60/4, VRG-20/2, VRG-4...
14G, 14H, 14H NA, 14M, 16G, 16H, 16H NA, 16M, 320C, 325B L, 325D L, 330C, 345B II, CTV40, G315B, G320, G325B, MP15, MP318, P360, S305, S365B, S365C, VHC-30, VHS-50, VHS-60/3, VHS-60/4, VRG-20/2, VRG-4...
1838273
BOLT
320C
320C
1838272
BOLT
320C, 321C, 323D L, 323D LN
320C, 321C, 323D L, 323D LN
320C, 320C FM, 320D, 320D FM, 320D L, 320D LRR, 320D RR, 320E LRR, 320E RR, 321C, 321D LCR