1977499 BOLT Caterpillar parts
325D FM LL, 330D FM, 414E, 416D, 416E, 416F, 420D, 420E, 420F, 422E, 422F, 424D, 428D, 428E, 428F, 430D, 430E, 430F, 432D, 432E, 432F, 434E, 434F, 438D, 442D, 442E, 444E, 444F, 446D, 450E, 450F, 5130,...
Rating:
Alternative (cross code) number:
CA1977499
197-7499
1977499
CA1977499
197-7499
1977499
Weight: 0.01 pounds 0 kg.
Information:
COATING/PLATING
Pigmented Organic Coating
GRIP LENGTH
2.1
mm
HEAD HEIGHT
2.92
mm
HEX SIZE
7
mm
LENGTH
25
mm
MATERIAL
Steel 830 MPa Min Tensile Strength
THREAD SIZE
M4X.7
ARTICULATED TRUCK, WHEEL TRACTOR,
Compatible equipment models: 1977499:
Information:
Remove & Install Crankshaft Rear Seal & Wear Sleeve
Start By:a. remove flywheel
Keep all parts clean from contaminants. Contaminants put into the system may cause rapid wear and shortened component life.
When a rear seal is replaced, the wear sleeve must also be replaced.
1. Remove the crankshaft rear seal with Tool (A). 2. Install Tool (C) as shown.3. Install Tool (B) between Tool (C) and the wear sleeve. Turn Tool (B) until the edge of the tool makes a flat place (crease) in the wear sleeve. Do this in two or more places until the wear sleeve is loose.4. Remove Tool (C) and the wear sleeve by hand. The following steps are for the installation of the crankshaft rear seal and wear sleeve.
Once there is a separation of a seal and wear sleeve they cannot be used again. Used seals cannot be used again.
Do not use any type of lubrication during the installation of the seal group.
The crankshaft seal and wear sleeve come as a set and must not be separated from each other at any time. Carefully read Special Instruction, SMHS8508, that is included with each seal and wear sleeve before any handling of the seal group is made.
5. Install the crankshaft rear seal and wear sleeve with Tooling (D) as follows: a. Put 9S-8871 Locator (1) in position on the crankshaft and install the 9S-8890 Bolts that hold it in place.b. Use 4C-9500 Quick Cure Primer to clean the outside diameter of the crankshaft flange (3) and the inside diameter of wear sleeve (2).c. Put 4C-9507 Retaining Compound on the outside diameter of crankshaft flange (3) and the inside diameter of wear sleeve (2).d. Put seal assembly [wear sleeve (2) and seal (6) on locator (1)]. Put 6V-7876 Installer (4) on locator (1) and install 9S-8858 Installer Nut (5). Put lubrication on the face of the washer and the nut.3. Tighten nut (5) until installer (4) comes in contact with locator (1).f. Remove Tooling (D) and check the wear sleeve and seal for correct installation.End By:a. install flywheel
Start By:a. remove flywheel
Keep all parts clean from contaminants. Contaminants put into the system may cause rapid wear and shortened component life.
When a rear seal is replaced, the wear sleeve must also be replaced.
1. Remove the crankshaft rear seal with Tool (A). 2. Install Tool (C) as shown.3. Install Tool (B) between Tool (C) and the wear sleeve. Turn Tool (B) until the edge of the tool makes a flat place (crease) in the wear sleeve. Do this in two or more places until the wear sleeve is loose.4. Remove Tool (C) and the wear sleeve by hand. The following steps are for the installation of the crankshaft rear seal and wear sleeve.
Once there is a separation of a seal and wear sleeve they cannot be used again. Used seals cannot be used again.
Do not use any type of lubrication during the installation of the seal group.
The crankshaft seal and wear sleeve come as a set and must not be separated from each other at any time. Carefully read Special Instruction, SMHS8508, that is included with each seal and wear sleeve before any handling of the seal group is made.
5. Install the crankshaft rear seal and wear sleeve with Tooling (D) as follows: a. Put 9S-8871 Locator (1) in position on the crankshaft and install the 9S-8890 Bolts that hold it in place.b. Use 4C-9500 Quick Cure Primer to clean the outside diameter of the crankshaft flange (3) and the inside diameter of wear sleeve (2).c. Put 4C-9507 Retaining Compound on the outside diameter of crankshaft flange (3) and the inside diameter of wear sleeve (2).d. Put seal assembly [wear sleeve (2) and seal (6) on locator (1)]. Put 6V-7876 Installer (4) on locator (1) and install 9S-8858 Installer Nut (5). Put lubrication on the face of the washer and the nut.3. Tighten nut (5) until installer (4) comes in contact with locator (1).f. Remove Tooling (D) and check the wear sleeve and seal for correct installation.End By:a. install flywheel
Cat SIS web machinery list:
Parts bolt Caterpillar catalog:
1472001
BOLT
320C FM, 320D, 320D FM, 320D FM RR, 320D L, 322C, 322C FM, 324D FM, 325C FM, 325D FM, 325D FM LL, 325D MH, 330B L, 330C, 330C FM, 330C L, 330D FM, 330D MH, 345B II, 345B L, 345C, 345C L, 345C MH, 365B...
320C FM, 320D, 320D FM, 320D FM RR, 320D L, 322C, 322C FM, 324D FM, 325C FM, 325D FM, 325D FM LL, 325D MH, 330B L, 330C, 330C FM, 330C L, 330D FM, 330D MH, 345B II, 345B L, 345C, 345C L, 345C MH, 365B...
3K3112
BOLT
10S, 814S, 816, D10, D11N, D250D, D250E, D25C, D300E, D9L
10S, 814S, 816, D10, D11N, D250D, D250E, D25C, D300E, D9L
4D8317
BOLT
16, 16G, 814S, 816, 824B, 825C, D250E, D9L
16, 16G, 814S, 816, 824B, 825C, D250E, D9L
3108642
BOLT-LOCKING
725, 725C, 730, 730C
725, 725C, 730, 730C
6T8853
BOLT-TRACK
5130, 5130B, D11N, D11R, D11T
5130, 5130B, D11N, D11R, D11T
4471721
BOLT
330D L, 336D, 336D L, 336D2, 336E, 336E H, 336E L, 336E LH, 336F L, 345C, 345D L, 349D, 349D L, 349E, 349E L, 349E L VG, 349F L, 374D L, 374F L, 385C, 385C FS, 385C L, 390D, 390D L, 568 FM LL, W345C M...
330D L, 336D, 336D L, 336D2, 336E, 336E H, 336E L, 336E LH, 336F L, 345C, 345D L, 349D, 349D L, 349E, 349E L, 349E L VG, 349F L, 374D L, 374F L, 385C, 385C FS, 385C L, 390D, 390D L, 568 FM LL, W345C M...
1121532
BOLT
2384C, 2484C, 322 FM L, 322B L, 322C, 322C FM, 324D FM, 324D FM LL, 324D L, 330, 330 FM L, 330B L, 330C, 330C FM, 330C L, 330C MH, 330D, 330D FM, 330D L, 330D MH, 336D L, 336E L, 345B, 345B II, 345B I...
2384C, 2484C, 322 FM L, 322B L, 322C, 322C FM, 324D FM, 324D FM LL, 324D L, 330, 330 FM L, 330B L, 330C, 330C FM, 330C L, 330C MH, 330D, 330D FM, 330D L, 330D MH, 336D L, 336E L, 345B, 345B II, 345B I...
3012299
BOLT-TRACK
325D FM, 325D FM LL, 330D FM, 330D L, 330D MH, 345B II, 345C, 345C L, 345C MH, 345D, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L, 349E L HVG, 349E L VG, 349F L, 365C L, 551, 552, 552 2, 568 FM LL
325D FM, 325D FM LL, 330D FM, 330D L, 330D MH, 345B II, 345C, 345C L, 345C MH, 345D, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L, 349E L HVG, 349E L VG, 349F L, 365C L, 551, 552, 552 2, 568 FM LL
4471718
BOLT
320C FM, 320D, 320D FM, 320D FM RR, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 323E L, 324E, 324E L, 324E LN, 329D L, 329E, 329E L, 336E, 336E H, 336E HVG, 336E L, 336E LH, 336E LN, 336F L, 345D L, 349...
320C FM, 320D, 320D FM, 320D FM RR, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 323E L, 324E, 324E L, 324E LN, 329D L, 329E, 329E L, 336E, 336E H, 336E HVG, 336E L, 336E LH, 336E LN, 336F L, 345D L, 349...
2012836
BOLT
324D, 324D L, 324D LN, 324E, 324E L, 324E LN, 325D, 325D L, 326D L, 329D, 329D L, 329D LN, 329E, 329E L, 329E LN, 330C, 330C L, 330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 3...
324D, 324D L, 324D LN, 324E, 324E L, 324E LN, 325D, 325D L, 326D L, 329D, 329D L, 329D LN, 329E, 329E L, 329E LN, 330C, 330C L, 330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 3...
1865649
BOLT
320B, 320C, 320D, 320D FM, 320D L, 320D2, 320D2 L, 320E, 320E LN, 321C, 322C, 322C FM, 323D L, 323D LN, 323D SA, 323D2 L, 323E L, 324D, 324D FM, 324D L, 324D LN, 324E, 324E L, 324E LN, 325C, 325C FM, ...
320B, 320C, 320D, 320D FM, 320D L, 320D2, 320D2 L, 320E, 320E LN, 321C, 322C, 322C FM, 323D L, 323D LN, 323D SA, 323D2 L, 323E L, 324D, 324D FM, 324D L, 324D LN, 324E, 324E L, 324E LN, 325C, 325C FM, ...
1504741
BOLT-TRACK
330B L, 330C, 330C FM, 330C L, 330D FM, 330D L, 330D MH, 345B, 345B II, 345B II MH, 345B L, 345C, 345C L, 345C MH, 551, 552, OEMS, TK751, TK752
330B L, 330C, 330C FM, 330C L, 330D FM, 330D L, 330D MH, 345B, 345B II, 345B II MH, 345B L, 345C, 345C L, 345C MH, 551, 552, OEMS, TK751, TK752
8C4982
BOLT-SOCKET HEAD
236D, 242D, 246D, 257D, 259D, 262D, 272D, 272D XHP, 277D, 279D, 287D, 289D, 299D, 299D XHP, 30/30, 3606, 3608, 3612, 3616, 416D, 416E, 416F, 420D, 420E, 420F, 422E, 422F, 428E, 428F, 430D, 430E, 430F,...
236D, 242D, 246D, 257D, 259D, 262D, 272D, 272D XHP, 277D, 279D, 287D, 289D, 299D, 299D XHP, 30/30, 3606, 3608, 3612, 3616, 416D, 416E, 416F, 420D, 420E, 420F, 422E, 422F, 428E, 428F, 430D, 430E, 430F,...
1641291
BOLT-SHOULDER
416D, 416E, 420D, 420E
416D, 416E, 420D, 420E
1836081
BOLT-SHOULDER
416D, 420D, 424D, 428D, 430D, 432D, 438D, 442D, 446D
416D, 420D, 424D, 428D, 430D, 432D, 438D, 442D, 446D
2224067
BOLT-SOCKET HEAD
414E, 416D, 416E, 420D, 420E, 422E, 424B, 424B HD, 424D, 428D, 428E, 430D, 430E, 432D, 432E, 434E, 438D, 442D, 442E, 444E, 450E, 450F, M313D, M315D, TH220B, TH330B, TH340B, TH350B, TH355B, TH460B, TH5...
414E, 416D, 416E, 420D, 420E, 422E, 424B, 424B HD, 424D, 428D, 428E, 430D, 430E, 432D, 432E, 434E, 438D, 442D, 442E, 444E, 450E, 450F, M313D, M315D, TH220B, TH330B, TH340B, TH350B, TH355B, TH460B, TH5...
1657019
BOLT
416D, 416E, 420D, 430D, 793D, 910G, C2.2, M312, M315
416D, 416E, 420D, 430D, 793D, 910G, C2.2, M312, M315
1729966
BOLT
307B, 320D, 320D L, 320D2, 320D2 L, 320E, 320E L, 320E LN, 328D LCR, 329D, 329D L, 329E, 329E L, 329E LN, 3512, 3512B, 3512C, 3516, 3516B, 3516C, 374F L, 416D, 420D, 424D, 428D, 430D, 432D, 438D, 442D...
307B, 320D, 320D L, 320D2, 320D2 L, 320E, 320E L, 320E LN, 328D LCR, 329D, 329D L, 329E, 329E L, 329E LN, 3512, 3512B, 3512C, 3516, 3516B, 3516C, 374F L, 416D, 420D, 424D, 428D, 430D, 432D, 438D, 442D...
1976657
BOLT-ROUND HEAD
416D, 416E, 416F, 420D, 420E, 420F, 422E, 424D, 428D, 428E, 430D, 430E, 430F, 432D, 432E, 434E, 438D, 442D, 442E, 444E, 446D, 450E, 450F, 621H, 621K, 623H, 623K, 623K LRC, 627H, 627K, 627K LRC
416D, 416E, 416F, 420D, 420E, 420F, 422E, 424D, 428D, 428E, 430D, 430E, 430F, 432D, 432E, 434E, 438D, 442D, 442E, 444E, 446D, 450E, 450F, 621H, 621K, 623H, 623K, 623K LRC, 627H, 627K, 627K LRC
2600045
BOLT-SPECIAL
416D, 416E, 416F, 420D, 420E, 420F, 422E, 424D, 428D, 428E, 430D, 430E, 430F, 432D, 432E, 434E, 438D, 442D, 442E, 444E, 446D, 450E, 450F, 621H
416D, 416E, 416F, 420D, 420E, 420F, 422E, 424D, 428D, 428E, 430D, 430E, 430F, 432D, 432E, 434E, 438D, 442D, 442E, 444E, 446D, 450E, 450F, 621H
1641265
BOLT
416D, 416E, 416F, 420D, 420E, 420F, 422E, 424D, 428D, 428E, 430D, 430E, 430F, 432D, 432E, 434E, 438D, 442D, 442E, 444E, 446D, 450E, 450F, 621H
416D, 416E, 416F, 420D, 420E, 420F, 422E, 424D, 428D, 428E, 430D, 430E, 430F, 432D, 432E, 434E, 438D, 442D, 442E, 444E, 446D, 450E, 450F, 621H
1053481
BOLT-SOCKET HEAD
301.4C, 301.7D, 301.7D CR, 302.2D, 302.4D, 303E CR, 307, 307B, 312D2, 312D2 GC, 312D2 L, 313D2, 313D2 LGP, 318D2 L, 325D, 330 L, 330D L, 385B, 416D, 416E, 416F, 420D, 420E, 420F, 422E, 424D, 428D, 428...
301.4C, 301.7D, 301.7D CR, 302.2D, 302.4D, 303E CR, 307, 307B, 312D2, 312D2 GC, 312D2 L, 313D2, 313D2 LGP, 318D2 L, 325D, 330 L, 330D L, 385B, 416D, 416E, 416F, 420D, 420E, 420F, 422E, 424D, 428D, 428...
3E8004
BOLT
315, 317, 320 L, 320N, 330D FM, 330D L, 330D LN, 336D, 336D L, 336D LN, 336D2, 336D2 L, 336E, 336E H, 336E L, 336E LH, 336E LN, 336F L, 416D, 420D, 424D, 428D, 430D, 432D, 438D, 442D, 446D, 5130, 568 ...
315, 317, 320 L, 320N, 330D FM, 330D L, 330D LN, 336D, 336D L, 336D LN, 336D2, 336D2 L, 336E, 336E H, 336E L, 336E LH, 336E LN, 336F L, 416D, 420D, 424D, 428D, 430D, 432D, 438D, 442D, 446D, 5130, 568 ...
2149035
BOLT
416D, 420D, 424D, 428D, 430D, 432D, 438D, 442D, 446D, 613G, 924G, 963D, 973D, CB-14B, D3K XL, D4K XL, D5K LGP, D6K LGP, PL61, TH210, TH215
416D, 420D, 424D, 428D, 430D, 432D, 438D, 442D, 446D, 613G, 924G, 963D, 973D, CB-14B, D3K XL, D4K XL, D5K LGP, D6K LGP, PL61, TH210, TH215