2643636 BOLT-SOCKET HEAD Caterpillar parts
312D, 315D L, 320D GC, 3512, 3512B, 374F L, 390F L, C2.2, C3.3, C32, C4.4, C6.6
Rating:
Alternative (cross code) number:
CA2643636
264-3636
2643636
CA2643636
264-3636
2643636
Weight: 0.01 pounds 0 kg.
Information:
DR TYPE
HEX
GRIP LENGTH
2
mm
HEAD DIAMETER
10.5
mm
HEAD HEIGHT
3.15
mm
HEAD STYLE
SHD
LENGTH
20
mm
MATERIAL
Stainless Steel
SOCKET SIZE
4
mm
THREAD SIZE
M6X1
EXCAVATOR, GENERATOR SET,
Compatible equipment models: 2643636:
Number on catalog scheme:
12
For full view, you need register
Information:
Removal Procedure
Personal injury can result from hot coolant, steam and alkali.At operating temperature, engine coolant is hot and under pressure. The radiator and all lines to heaters or the engine contain hot coolant or steam. Any contact can cause severe burns.Remove cooling system pressure cap slowly to relieve pressure only when engine is stopped and cooling system pressure cap is cool enough to touch with your bare hand.Do not attempt to tighten hose connections when the coolant is hot, the hose can come off causing burns.Cooling System Coolant Additive contains alkali. Avoid contact with skin and eyes.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Drain the coolant from the system into a suitable container for storage or disposal. Refer to Operation and Maintenance Manual, "Cooling System Coolant (ELC) - Change".
Illustration 1 g01020800
Typical example
Remove nuts (1) from regulator housing (2) .
Remove regulator housing (2) . Remove studs (3) , if necessary.
Remove pipe plug (4) , if necessary.
Remove gasket (5) .
Remove water temperature regulator (6) . Remove pipe plug (7) , if necessary.
Remove lip seal (8) from regulator housing (2) .Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Group 1
B 5P-3413 Pipe Sealant 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 2 g01020800
Typical example
Install studs (3) in the water outlet manifold. Position gasket (5) on studs (3) .
Position the seal with the lip toward the inside of the housing. Lubricate the lip of the seal with glycerin. Install lip seal (8) in regulator housing (2) with Tooling (A) . Install the seal until contact with the counterbore in the housing.
Install pipe plug (4) and pipe plug (7) with Tooling (B) .
Position water temperature regulator (6) in regulator housing (2) .
Install regulator housing (2) with nuts (1) .
Refill the cooling system with coolant. Refer to Operation and Maintenance Manual, "Cooling System Coolant (ELC) - Change".
Personal injury can result from hot coolant, steam and alkali.At operating temperature, engine coolant is hot and under pressure. The radiator and all lines to heaters or the engine contain hot coolant or steam. Any contact can cause severe burns.Remove cooling system pressure cap slowly to relieve pressure only when engine is stopped and cooling system pressure cap is cool enough to touch with your bare hand.Do not attempt to tighten hose connections when the coolant is hot, the hose can come off causing burns.Cooling System Coolant Additive contains alkali. Avoid contact with skin and eyes.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Drain the coolant from the system into a suitable container for storage or disposal. Refer to Operation and Maintenance Manual, "Cooling System Coolant (ELC) - Change".
Illustration 1 g01020800
Typical example
Remove nuts (1) from regulator housing (2) .
Remove regulator housing (2) . Remove studs (3) , if necessary.
Remove pipe plug (4) , if necessary.
Remove gasket (5) .
Remove water temperature regulator (6) . Remove pipe plug (7) , if necessary.
Remove lip seal (8) from regulator housing (2) .Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Group 1
B 5P-3413 Pipe Sealant 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 2 g01020800
Typical example
Install studs (3) in the water outlet manifold. Position gasket (5) on studs (3) .
Position the seal with the lip toward the inside of the housing. Lubricate the lip of the seal with glycerin. Install lip seal (8) in regulator housing (2) with Tooling (A) . Install the seal until contact with the counterbore in the housing.
Install pipe plug (4) and pipe plug (7) with Tooling (B) .
Position water temperature regulator (6) in regulator housing (2) .
Install regulator housing (2) with nuts (1) .
Refill the cooling system with coolant. Refer to Operation and Maintenance Manual, "Cooling System Coolant (ELC) - Change".
Cat SIS web machinery list:
Parts bolt Caterpillar catalog:
2606672
BOLT
C2.2, C3.3, C4.4
C2.2, C3.3, C4.4
621H, 770G, 770G OEM, 772G, 772G OEM, 773F, 773G, 773G LRC, 773G OEM, 775F, 775G, 775G LRC, 775G OEM, 777F, 777G, 793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ, 844H, 844K, 854K, 990H, 990K, 992K, 993K, ...
336F L, 349F L, 374F L, 390F L, 966M, 966M XE, 972M, 972M XE, 980M, 982M, C13, C15, C18, C2.2, C3.3, C4.4, C7.1, C9.3, D9T
2606706
BOLT-SOCKET HEAD
C3.3, C32, C4.4, C6.6
C3.3, C32, C4.4, C6.6
2606673
BOLT
793F, 973C, C3.3, C4.4, CB-54, CB-64, M313D
793F, 973C, C3.3, C4.4, CB-54, CB-64, M313D
2606678
BOLT
C2.2, C3.3, C4.4, C6.6
C2.2, C3.3, C4.4, C6.6
2630164
BOLT
C1.5, C4.4, C6.6
C1.5, C4.4, C6.6
2662801
BOLT-LOCKING
C4.4
C4.4
2606712
BOLT
C4.4
C4.4
4168193
BOLT
C2.2, C4.4
C2.2, C4.4
2643630
BOLT
C4.4, C6.6
C4.4, C6.6
2739269
BOLT
C4.4
C4.4