2683205 BOLT Caterpillar parts
16M, 2384C, 2484C, 301.6C, 302.5C, 559C, 579C, 583T, 587R, 587T
Rating:
Alternative (cross code) number:
CA2683205
268-3205
2683205
CA2683205
268-3205
2683205
Weight: 0.16 pounds 0 kg.
Information:
COATING/PLATING
Dacromet 320 Plus L Coating
GRIP LENGTH
6
mm
HEAD HEIGHT
0
mm
HEX SIZE
21
mm
LENGTH
50
mm
MATERIAL
Steel - 1040 MPa Min Tensile Strength
THREAD SIZE
M14X2
KNUCKLEBOOM LOADER, PIPELAYER,
Compatible equipment models: 2683205:
Information:
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7574 Link Bracket 2 Start By:
Remove the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Remove".
Remove the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting Motor - Remove and Install".
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products.Dispose of all fluids according to local regulations and mandates.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01008304
Remove bolts (1) that fasten the engine oil pan to flywheel housing (2).
Illustration 2 g01058428
Install Tooling (A) and a suitable lifting device on flywheel housing (2). The weight of flywheel housing (2) is approximately 80 kg (175 lb).
Remove bolts (3). Remove the flywheel housing from the cylinder block.
Remove gasket (4) from the flywheel housing. Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 138-7574 Link Bracket 2
B - Loctite Blue RTV Silicone -
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Thoroughly clean the flywheel housing and the rear face of the cylinder block. These components must be free of the following substances: oil, fuel, water, gasket adhesive, assembly compounds, and any other foreign material.
Illustration 3 g01058428
Install Tooling (A) and a suitable lifting device on flywheel housing (2). The weight of flywheel housing (2) is approximately 80 kg (175 lb).
Install gasket (4) on the dowel pins of the cylinder block. Apply Tooling (B) to the bottom of gasket (4) in order to fill the space at the cylinder block, the flywheel housing, and the engine oil pan.
Position flywheel housing (2) on the cylinder block. Install bolts (3) and remove Tooling (A).
Illustration 4 g00551652
Tighten the bolts, as follows:
In a numerical sequence, tighten Bolt (1) through Bolt (9) to a torque of 100 20 N m (30 15 lb ft).
In a numerical sequence, tighten Bolt (10) through Bolt (24) to a torque of 40 10 N m (30 7 lb ft).
In a numerical sequence, again tighten Bolt (1) through Bolt (9) to a torque of 135 20 N m (100 15 lb ft).
In a numerical sequence, again tighten Bolt (10) through Bolt (24) to a torque of 55 10 N m (40 7 lb ft).
Illustration 5 g01008304
Install bolts (1) that fasten the engine oil pan to flywheel housing (2). End By:
Install the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting Motor - Remove and Install".
Install the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Install".
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7574 Link Bracket 2 Start By:
Remove the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Remove".
Remove the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting Motor - Remove and Install".
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products.Dispose of all fluids according to local regulations and mandates.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01008304
Remove bolts (1) that fasten the engine oil pan to flywheel housing (2).
Illustration 2 g01058428
Install Tooling (A) and a suitable lifting device on flywheel housing (2). The weight of flywheel housing (2) is approximately 80 kg (175 lb).
Remove bolts (3). Remove the flywheel housing from the cylinder block.
Remove gasket (4) from the flywheel housing. Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 138-7574 Link Bracket 2
B - Loctite Blue RTV Silicone -
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Thoroughly clean the flywheel housing and the rear face of the cylinder block. These components must be free of the following substances: oil, fuel, water, gasket adhesive, assembly compounds, and any other foreign material.
Illustration 3 g01058428
Install Tooling (A) and a suitable lifting device on flywheel housing (2). The weight of flywheel housing (2) is approximately 80 kg (175 lb).
Install gasket (4) on the dowel pins of the cylinder block. Apply Tooling (B) to the bottom of gasket (4) in order to fill the space at the cylinder block, the flywheel housing, and the engine oil pan.
Position flywheel housing (2) on the cylinder block. Install bolts (3) and remove Tooling (A).
Illustration 4 g00551652
Tighten the bolts, as follows:
In a numerical sequence, tighten Bolt (1) through Bolt (9) to a torque of 100 20 N m (30 15 lb ft).
In a numerical sequence, tighten Bolt (10) through Bolt (24) to a torque of 40 10 N m (30 7 lb ft).
In a numerical sequence, again tighten Bolt (1) through Bolt (9) to a torque of 135 20 N m (100 15 lb ft).
In a numerical sequence, again tighten Bolt (10) through Bolt (24) to a torque of 55 10 N m (40 7 lb ft).
Illustration 5 g01008304
Install bolts (1) that fasten the engine oil pan to flywheel housing (2). End By:
Install the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting Motor - Remove and Install".
Install the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Install".
Caterpillar parts catalog:
Parts bolt Caterpillar catalog:
7X0423
BOLT
120K, 120K 2, 120M, 120M 2, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 160K, 160M, 160M 2, 160M 3, 160M 3 AWD, 583R, 583T, D10T, D9R, D9T
120K, 120K 2, 120M, 120M 2, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 160K, 160M, 160M 2, 160M 3, 160M 3 AWD, 583R, 583T, D10T, D9R, D9T
1123928
BOLT
120K, 120K 2, 14M, 16M, 322 LN, 322B LN, 322C, 324D, 324D L, 324D LN, 325B L, 325C, 325D, 325D FM, 325D FM LL, 325D L, 325D MH, 329D L, 329D LN, CB-44B, CB-54B, D3G, D4G, D5G, M325C MH, M325D L MH, M3...
120K, 120K 2, 14M, 16M, 322 LN, 322B LN, 322C, 324D, 324D L, 324D LN, 325B L, 325C, 325D, 325D FM, 325D FM LL, 325D L, 325D MH, 329D L, 329D LN, CB-44B, CB-54B, D3G, D4G, D5G, M325C MH, M325D L MH, M3...
1657637
BOLT-SOCKET HEAD
572R II, 583T, 587R, 587T, D7R II, D8R, D8R II, D8T, PL83, PL87
572R II, 583T, 587R, 587T, D7R II, D8R, D8R II, D8T, PL83, PL87
7X0429
BOLT
10-20B, 12M 2, 140M, 160M, 515, 525, 587T, AP-1055D, AS3251C, AS3301C, BG-2455D, BG-260D, CB-614, CP-433C, CP-433E, CP-44, CP-56, CP-563, CP-573E, CP-64, CP-68B, CP-74B, CS-323C, CS-433C, CS-433E, CS-...
10-20B, 12M 2, 140M, 160M, 515, 525, 587T, AP-1055D, AS3251C, AS3301C, BG-2455D, BG-260D, CB-614, CP-433C, CP-433E, CP-44, CP-56, CP-563, CP-573E, CP-64, CP-68B, CP-74B, CS-323C, CS-433C, CS-433E, CS-...
7Y5232
BOLT
14M, 16H, 16M, 345B, 345B L, 365B, 375, 375 L, 5080, 5110B, 797, 797B, 797F, 844, 844H, 844K, 990 II, 990H, 990K, D6G2 LGP, D6G2 XL, D7E, D7E LGP
14M, 16H, 16M, 345B, 345B L, 365B, 375, 375 L, 5080, 5110B, 797, 797B, 797F, 844, 844H, 844K, 990 II, 990H, 990K, D6G2 LGP, D6G2 XL, D7E, D7E LGP
7Y5215
BOLT-SOCKET HEAD
1390, 2484C, 2590, 320 L, 320B, 320C, 320D, 320D FM, 320D2, 320D2 L, 320N, 322 FM L, 322 LN, 322B, 322B L, 322B LN, 322C, 322C FM, 323D L, 323D LN, 323D SA, 324D, 324D FM, 324D FM LL, 324D L, 324D LN,...
1390, 2484C, 2590, 320 L, 320B, 320C, 320D, 320D FM, 320D2, 320D2 L, 320N, 322 FM L, 322 LN, 322B, 322B L, 322B LN, 322C, 322C FM, 323D L, 323D LN, 323D SA, 324D, 324D FM, 324D FM LL, 324D L, 324D LN,...
1J0962
BOLT
16G, 16M, 8A
16G, 16M, 8A
6V7729
BOLT
16M, 657E, 657G, 777F, 777G, 793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ
16M, 657E, 657G, 777F, 777G, 793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ
2869155
BOLT-SELF-LOCKING
120M, 120M 2, 12M, 12M 2, 12M 3, 12M 3 AWD, 140M, 140M 2, 140M 3, 140M 3 AWD, 14M, 160M, 160M 2, 160M 3, 160M 3 AWD, 16M, 938H, IT38H
120M, 120M 2, 12M, 12M 2, 12M 3, 12M 3 AWD, 140M, 140M 2, 140M 3, 140M 3 AWD, 14M, 160M, 160M 2, 160M 3, 160M 3 AWD, 16M, 938H, IT38H
1073953
BOLT
120M, 12M, 14M, 16M, 345B II, 345C, 345C L, 365B, 365B II, 365B L, 365C, 365C L, 365C L MH, 374D L, 374F L, 375, 375 L, 385B, 385C, 385C FS, 385C L, 385C L MH, 390D, 5080, 5090B, 5110B, 525B, 525C, 53...
120M, 12M, 14M, 16M, 345B II, 345C, 345C L, 365B, 365B II, 365B L, 365C, 365C L, 365C L MH, 374D L, 374F L, 375, 375 L, 385B, 385C, 385C FS, 385C L, 385C L MH, 390D, 5080, 5090B, 5110B, 525B, 525C, 53...
1D4691
BOLT-CARRIAGE
120M, 120M 2, 12M, 12M 2, 12M 3, 12M 3 AWD, 140M, 140M 2, 140M 3, 140M 3 AWD, 14G, 14H, 14H NA, 14M, 160M, 160M 2, 160M 3, 160M 3 AWD, 16G, 16H, 16H NA, 16M, 24H, 24M, 785B, 785C, 789B, 789C, 793B, 79...
120M, 120M 2, 12M, 12M 2, 12M 3, 12M 3 AWD, 140M, 140M 2, 140M 3, 140M 3 AWD, 14G, 14H, 14H NA, 14M, 160M, 160M 2, 160M 3, 160M 3 AWD, 16G, 16H, 16H NA, 16M, 24H, 24M, 785B, 785C, 789B, 789C, 793B, 79...
1121532
BOLT
2384C, 2484C, 322 FM L, 322B L, 322C, 322C FM, 324D FM, 324D FM LL, 324D L, 330, 330 FM L, 330B L, 330C, 330C FM, 330C L, 330C MH, 330D, 330D FM, 330D L, 330D MH, 336D L, 336E L, 345B, 345B II, 345B I...
2384C, 2484C, 322 FM L, 322B L, 322C, 322C FM, 324D FM, 324D FM LL, 324D L, 330, 330 FM L, 330B L, 330C, 330C FM, 330C L, 330C MH, 330D, 330D FM, 330D L, 330D MH, 336D L, 336E L, 345B, 345B II, 345B I...
2695224
BOLT
300.9D, 301.6C, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313D2, 313D2 LGP, 314D CR, 314D LCR, 314E CR, 314E LCR
300.9D, 301.6C, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313D2, 313D2 LGP, 314D CR, 314D LCR, 314E CR, 314E LCR
2268599
BOLT
301.6C, 302.5C
301.6C, 302.5C
2500394
BOLT
301.6C
301.6C
2230386
BOLT
301.6C
301.6C
2230408
BOLT
301.6C
301.6C
2230323
BOLT
301.6C
301.6C
2683212
BOLT
302.5C
302.5C
2234295
BOLT
302.5C, 587R, 587T, CP-573E, CP-64, CP-663E, CP-68B, CP-74B, CP-76, CS-56B, CS-64, CS-663E, CS-683E, CS-68B, CS-74, CS-74B, CS-76B, CS-78B
302.5C, 587R, 587T, CP-573E, CP-64, CP-663E, CP-68B, CP-74B, CP-76, CS-56B, CS-64, CS-663E, CS-683E, CS-68B, CS-74, CS-74B, CS-76B, CS-78B
2596120
BOLT-SOCKET HEAD
302.5C
302.5C
1505984
BOLT
302.5C, 924G, 924GZ, 930G, HF201, HF201B, HF221, IT28G
302.5C, 924G, 924GZ, 930G, HF201, HF201B, HF221, IT28G
1053485
BOLT-SOCKET HEAD
302.5C, 312D2, 316E L, 318E L, 320 L, 320B, 320B L, 320C, 320D, 320D L, 320E LN, 322 LN, 322B L, 322B LN, 322C, 323E L, 324D, 324D FM, 324D FM LL, 324D L, 324D LN, 325B L, 325C, 325D, 325D FM, 325D FM...
302.5C, 312D2, 316E L, 318E L, 320 L, 320B, 320B L, 320C, 320D, 320D L, 320E LN, 322 LN, 322B L, 322B LN, 322C, 323E L, 324D, 324D FM, 324D FM LL, 324D L, 324D LN, 325B L, 325C, 325D, 325D FM, 325D FM...
1990957
BOLT
302.5C, 901C, 902C, 903C, 910K, 914K
302.5C, 901C, 902C, 903C, 910K, 914K