3H6740 BOLT Caterpillar parts
3508, 3512, 3516, D337, D343, D353C, D375D, D4D
Rating:
Alternative (cross code) number:
CA3H6740
3H-6740
3H6740
CA3H6740
3H-6740
3H6740
Weight: 0.010 pounds 0 kg.
Information:
GRIP LENGTH
44.45
mm
HEAD HEIGHT
7.37
mm
HEX SIZE
14.29
mm
LENGTH
69.85
mm
MATERIAL
Stainless Steel - 758 MPa Minimum Tensile Strength
THREAD SIZE
.38-16
GEN SET ENGINE, VEHICULAR ENGINE,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$5.51
11 Aug 2023
Amazon.com
CTP 3H6740 Cap Screw for Heavy Equipment
CTP Cap Screw Only || Sold In Each || Easy in-and-out fit
CTP Cap Screw Only || Sold In Each || Easy in-and-out fit
$2.45
12 Apr 2023
Amazon.com
CTP 3H6740 Cap Screw for Heavy Equipment
CTP Cap Screw Only || Sold In Each || Easy in-and-out fit
CTP Cap Screw Only || Sold In Each || Easy in-and-out fit
$1.55
07 Feb 2023
Amazon.com
CTP 3H6740 Cap Screw for Heavy Equipment
CTP Cap Screw Only || Sold In Each || Easy in-and-out fit
CTP Cap Screw Only || Sold In Each || Easy in-and-out fit
Number on catalog scheme:
11
For full view, you need register
Compatible equipment models: 3H6740:
Information:
Description
Illustration 1 g01276398
(1) Power distribution board (PWD) The power distribution board (PWD) is located on the upper left panel of the flywheel cabinet.The PWD distributes all 24 VDC power to the following components: MMU boards, vacuum pump, fans and controls.The lower left panel of the flywheel cabinet contains the T1 transformer for the flywheel. T1 power is fed from the circuit breaker that is located on the lower left panel of the flywheel cabinet.Removal Procedure
Refer to Systems Operation, Testing and Adjusting, UENR3954, "Internal Component Preremoval Steps (Flywheel Cabinet)" in order to shut down the system and gain access to internal components.
Electrostatic discharge can damage integrated circuits or semiconductors if you touch bus connector pins. When not in use, keep the module in a static-shield bag. Use the following guidelines when you handle any module:Touch a grounded object to discharge static potential.Wear an approved wrist-strap grounding device.Do not touch the bus connector or connector pins.Do not touch circuit components inside the module.If available, use a static-safe work station.
Remove the static switch assembly in order to access the board (1). Refer to Systems Operation, Testing and Adjusting, UENR3954, "Static Switch" for the removal procedure.
Illustration 2 g01277014
PWD board connections
Disconnect all connectors from the board (1). Verify each label for each connector for subsequent installation. Refer to Illustration 2 for wire connections.
Disconnect the nine white plastic standoffs that connect the board (1) to the left panel. Note: The board (1) must be removed from the standoffs without bending the board (1).
Compress the head of each standoff so that the board (1) is not locked, but the board (1) is still attached to the standoff.
Remove the board (1) from all standoffs at the same time. Installation Procedure
Electrostatic discharge can damage integrated circuits or semiconductors if you touch bus connector pins. When not in use, keep the module in a static-shield bag. Follow these guidelines when you handle any module:Touch a grounded object to discharge static potential.Wear an approved wrist-strap grounding device.Do not touch the bus connector or connector pins.Do not touch circuit components inside the module.If available, use a static-safe work station.
Position the board (1) in the cabinet over the white standoffs that are connected to the left panel. Install the board (1). Verify that all the standoffs are locked into the correct position.
Connect the wire connectors. Verify the labeling of each connector for proper placement. Refer to Illustration 2.
Illustration 1 g01276398
(1) Power distribution board (PWD) The power distribution board (PWD) is located on the upper left panel of the flywheel cabinet.The PWD distributes all 24 VDC power to the following components: MMU boards, vacuum pump, fans and controls.The lower left panel of the flywheel cabinet contains the T1 transformer for the flywheel. T1 power is fed from the circuit breaker that is located on the lower left panel of the flywheel cabinet.Removal Procedure
Refer to Systems Operation, Testing and Adjusting, UENR3954, "Internal Component Preremoval Steps (Flywheel Cabinet)" in order to shut down the system and gain access to internal components.
Electrostatic discharge can damage integrated circuits or semiconductors if you touch bus connector pins. When not in use, keep the module in a static-shield bag. Use the following guidelines when you handle any module:Touch a grounded object to discharge static potential.Wear an approved wrist-strap grounding device.Do not touch the bus connector or connector pins.Do not touch circuit components inside the module.If available, use a static-safe work station.
Remove the static switch assembly in order to access the board (1). Refer to Systems Operation, Testing and Adjusting, UENR3954, "Static Switch" for the removal procedure.
Illustration 2 g01277014
PWD board connections
Disconnect all connectors from the board (1). Verify each label for each connector for subsequent installation. Refer to Illustration 2 for wire connections.
Disconnect the nine white plastic standoffs that connect the board (1) to the left panel. Note: The board (1) must be removed from the standoffs without bending the board (1).
Compress the head of each standoff so that the board (1) is not locked, but the board (1) is still attached to the standoff.
Remove the board (1) from all standoffs at the same time. Installation Procedure
Electrostatic discharge can damage integrated circuits or semiconductors if you touch bus connector pins. When not in use, keep the module in a static-shield bag. Follow these guidelines when you handle any module:Touch a grounded object to discharge static potential.Wear an approved wrist-strap grounding device.Do not touch the bus connector or connector pins.Do not touch circuit components inside the module.If available, use a static-safe work station.
Position the board (1) in the cabinet over the white standoffs that are connected to the left panel. Install the board (1). Verify that all the standoffs are locked into the correct position.
Connect the wire connectors. Verify the labeling of each connector for proper placement. Refer to Illustration 2.
Caterpillar parts catalog:
Parts bolt Caterpillar catalog:
120, 12E, 12F, 14E, 613, 613B, 950, D343, D5E
3512, 57, 621, 621E, 621F, 621G, 621H, 621K, 623B, 623E, 623F, 623G, 623H, 623K, 623K LRC, 627B, 627E, 627F, 627G, 627H, 627K, 627K LRC, 936F, 988B, 988F, 988F II, AD30, D10R, D6H, D6H XL, D6R, D7R
16G, 206, 214, 224, 983B, AP-1200, AP-800, CB-424, CP-433B, CS-431B, D353C, G342C, PR-75, WE-601B
205B, 211B, 215, 215B, 215C, 215D, 225, 229, 312B L, 312C, 323D LN, 561B, 561C, 633, 633D, 639D, 941, 943, 951B, 953, 953B, 953C, 955C, 955H, 955K, 955L, 977D, D4D, D4E, D4E SR, D5, D5B, D5C, D5E, D6C...
225, 312B L, 312C, 518, 941, 943, 951B, 953, 953B, 953C, 955L, D250B, D4D, D4E, D4E SR, D5, D5B, D5C, D5E, OEMS
225, 621, 621B, 621E, 621G, 623B, 623G, 627B, 627E, 627F, 627G, 631D, 631E, 631G, 633D, 637D, 637E, 637G, 639D, 641B, 651B, 651E, 657B, 657E, 814B, 814F, 814F II, 815B, 815F, 815F II, 834B, 941, 951B,...
215, 931, 931B, 931C, 931C II, 933, 933C, 935B, 935C, 935C II, 941, 955C, AP-1050, D3, D3B, D3C, D3C II, D3C III, D3G, D3K XL, D3K2 LGP, D4B, D4C, D4C II, D4C III, D4D, D4E, D4G, D4K XL, D4K2 XL, PR-4...
120, 120B, 12E, 140, 245, 651E, 657G, 789, 789B, 789C, 789D, 793, 793B, 793C, 793D, 793F, 793F CMD, 793F OEM, 793F-XQ, 824G II, 824H, 824K, 825G II, 825H, 825K, 826G II, 826H, 826K, 834G, 834H, 834K, ...
120G, 12F, 12G, 130G, 140G, 14E, 14G, 14H, 14H NA, 16, 160G, 16G, 227, 627, 630B, 633, 633D, 637, 639D, 641B, 657, 657B, 657E, 784B, 784C, 785, 785B, 785C, 785D, 789, 789B, 789C, 789D, 793, 834, 950, ...
931, 931B, 931C, 933, 935B, 939, 941, 951B, 955H, 955K, 955L, D3, D3B, D3C, D3C III, D4B, D4C, D4C III, D4D, D4E, D4E SR, D5C, D5C III
D4D, D4E, D4E SR
14E, 572G, 627, 627B, 627E, 627F, 627G, 627H, 627K, 627K LRC, 637B, 637D, 637E, 637G, 941, 951B, D4D, D7G, D7G2, D9R, D9T
2M5528
BOLT (DRILLED)
D337F, D342C, D353C, D397D, D8H
D337F, D342C, D353C, D397D, D8H
2M2573
BOLT (PLAIN)
D337F, D342C, D353C, D397D, D8H
D337F, D342C, D353C, D397D, D8H
5H2573
BOLT
16, 1693, 657, 769, 988, D326F, D337F, D343
16, 1693, 657, 769, 988, D326F, D337F, D343
118, 119, 1693, 30, 518, 528, 621, 630B, 657, 814, 815, 815B, 816B, 824B, 825B, 826B, 834, 834B, 920, 930, 950, 966C, 966D, 980, 980B, 988B, D337F, D343, D364, D375D, D397D
120, 120B, 12E, 140, 140B, 14G, 16G, 215, 215B, 225, 227, 235, 235D, 245, 245B, 245D, 3204, 3406, 3406B, 3406C, 3406E, 3408, 50, 5110B, 515, 525, 545, 613, 613B, 613C, 615, 615C, 621, 621B, 621E, 623,...
3516, 3516B, 621B, 637E, 769, 977D, 977H, 992C, D379A, D398, D5, G379
120, 120B, 12E, 12F, 140, 140B, 14E, 1674, 2470C, 2570C, 2670C, 553C, 563C, 573C, 583H, 583K, 594, 594H, 623B, 627B, 776, 777, 951, 977D, 983, D364, D375D, D4E, D7F, D8H, D8K, D9E, D9G, D9H, G343, HF2...
16, 1693, 3406, 631C, 641B, 650B, 657, 657B, 666, 769, 772, 773, 777, 824B, 826B, 834, 936F, 983, 988, 992, D342C, D348, D8H, D9G, D9H
D342, D342C, D353C, D8H, D9E, G342C
120G, 12G, 14G, 16G, 245, 50, 623, 627, 633, 657B, 666, 910, 955C, 963, 973, 977D, 980, 980C, 983, CS-643, D10, D398, D399, D6C, D6D, G399, PF-300C, PM-465
225, 229, 235, 235B, 245, 518, 518C, 528, 528B, 530B, 561D, 621, 621B, 621R, 623B, 627, 627B, 784B, 785, 785B, 789, 789B, 789C, 814, 8D, 931B, 936, 950, 966C, 966D, 966F, 966R, 977D, 980, 980B, 983, 9...
16G, 245, 3406, 3406B, 3406C, 3408, 3408C, 3408E, 3412, 3412C, 3412E, 578, 621E, 623E, 627E, 631E, 637E, 657E, 826C, 834G, 836G, 910, 931B, 950, 980C, 988B, 988F, C15, C18, CG137-08, CG137-12, CPT372,...