3L2540 BOLT-SOCKET HEAD Caterpillar parts
215, 30/30, 3304, 3306, 3508B, 3512B, 3606, 3608, 3612, 3616, 528, 621E, 621F, 623E, 623F, 627E, 627F, 631E, 633E II, 637E, 651E, 657E, 69D, 769C, 769D, 771C, 771D, 772B, 773B, 773D, 773E, 775B, 775D,...
Rating:
Alternative (cross code) number:
CA3L2540
3L-2540
3L2540
CA3L2540
3L-2540
3L2540
Weight: 0.01 pounds 0 kg.
Information:
DR TYPE
HEX
GRIP LENGTH
1.98
mm
HEAD DIAMETER
7.92
mm
HEAD HEIGHT
4.83
mm
HEAD STYLE
SHD
LENGTH
19.05
mm
MATERIAL
Steel Rc 39 - 45
SOCKET SIZE
3.96
mm
THREAD SIZE
NO 10-24
ARTICULATED TRUCK, WHEEL TRACTOR,
This part in 8 request:
Show.
This information for suppliers only!
2016-12-28
2016-12-28
2016-12-28
2016-12-28
2016-12-28
2016-12-28
2016-12-28
2016-12-28
Compatible equipment models: 3L2540:
Number on catalog scheme:
1
For full view, you need register
Information:
Probable Causes
Air inlet or exhaust system
Engine speed/timing sensor
Atmospheric pressure sensor
Boost pressure sensor
"Fuel Position" and/or "FRC Fuel Limit"
Flash file
Fuel quality
Valve adjustmentRecommended Actions
Air Inlet or Exhaust System
Check the air inlet system for restrictions and/or for leaks.
Check for an air filter restriction.
Perform a visual inspection of the system for restrictions and/or for leaks in the air inlet piping .
Ensure that the turbocharger is in good repair.
Check the exhaust system for restrictions.
Repair any leaks that were found. Remove any restrictions that were found. Replace any damaged components that were found.Engine Speed/Timing
Check the calibration of the engine speed/timing sensor. Refer to Troubleshooting, "Engine Speed/Timing Sensor - Calibrate".
Verify that the crankshaft and the camshaft drive gears are set with the proper orientation.Atmospheric Pressure Sensor
Check the atmospheric pressure sensor for dirt and/or for debris. Remove any dirt and/or debris that is present. The correct reading for the atmospheric pressure is between 50 kPa (7.25 psi) and 100 kPa (14.5 psi).Boost Pressure Sensor, "Fuel Position", and/or "FRC Fuel Limit"
Monitor the status of "Fuel Position" and "Rated Fuel Limit" while the engine is operating under full load. If "Fuel Position" equals "Rated Fuel Limit" and "Fuel Position" is less than "FRC Fuel Limit", the Electronic Control Module (ECM) is providing the correct control. Otherwise, proceed to the next Step.
Verify that there are no active diagnostic codes for the boost pressure sensor.
Monitor the status of "Boost Pressure" and "Atmospheric Pressure" on the Caterpillar Electronic Technician (ET). When the engine is not running, "Boost Pressure" should be 0 kPa (0 psi).Note: A problem with the "FRC Fuel Limit" will only cause black smoke during acceleration. A problem with the "FRC Fuel Limit" will not cause black smoke during steady state operation.Flash File
Verify that the correct flash file is installed. Refer to Troubleshooting, "Flash Programming" for information.Fuel Quality
Cold weather adversely affects the characteristics of the fuel.Valve Adjustment
Check the valve adjustment.
Air inlet or exhaust system
Engine speed/timing sensor
Atmospheric pressure sensor
Boost pressure sensor
"Fuel Position" and/or "FRC Fuel Limit"
Flash file
Fuel quality
Valve adjustmentRecommended Actions
Air Inlet or Exhaust System
Check the air inlet system for restrictions and/or for leaks.
Check for an air filter restriction.
Perform a visual inspection of the system for restrictions and/or for leaks in the air inlet piping .
Ensure that the turbocharger is in good repair.
Check the exhaust system for restrictions.
Repair any leaks that were found. Remove any restrictions that were found. Replace any damaged components that were found.Engine Speed/Timing
Check the calibration of the engine speed/timing sensor. Refer to Troubleshooting, "Engine Speed/Timing Sensor - Calibrate".
Verify that the crankshaft and the camshaft drive gears are set with the proper orientation.Atmospheric Pressure Sensor
Check the atmospheric pressure sensor for dirt and/or for debris. Remove any dirt and/or debris that is present. The correct reading for the atmospheric pressure is between 50 kPa (7.25 psi) and 100 kPa (14.5 psi).Boost Pressure Sensor, "Fuel Position", and/or "FRC Fuel Limit"
Monitor the status of "Fuel Position" and "Rated Fuel Limit" while the engine is operating under full load. If "Fuel Position" equals "Rated Fuel Limit" and "Fuel Position" is less than "FRC Fuel Limit", the Electronic Control Module (ECM) is providing the correct control. Otherwise, proceed to the next Step.
Verify that there are no active diagnostic codes for the boost pressure sensor.
Monitor the status of "Boost Pressure" and "Atmospheric Pressure" on the Caterpillar Electronic Technician (ET). When the engine is not running, "Boost Pressure" should be 0 kPa (0 psi).Note: A problem with the "FRC Fuel Limit" will only cause black smoke during acceleration. A problem with the "FRC Fuel Limit" will not cause black smoke during steady state operation.Flash File
Verify that the correct flash file is installed. Refer to Troubleshooting, "Flash Programming" for information.Fuel Quality
Cold weather adversely affects the characteristics of the fuel.Valve Adjustment
Check the valve adjustment.
Cat SIS web machinery list:
Parts bolt Caterpillar catalog:
10S, 814S, 816, D10, D11N, D250D, D250E, D25C, D300E, D9L
16, 16G, 814S, 816, 824B, 825C, D250E, D9L
AD45, AD45B, AD55, AD55B, AD60, R1300, R1300G, R1300G II, R1600, R2900, R2900G, R3000H
AD30, AD40, AD45, AD45B, AD55, AD55B, AD60, AE40, R1300, R1300G, R1300G II, R1600, R1600G, R1700 II, R1700G, R2900, R2900G, R3000H
R1600, R1600G, R1700 II, R1700G, R2900, R2900G, R3000H
324E, 324E L, 324E LN, 328D LCR, 329E, 329E L, 329E LN, 336E, 336E H, 336E L, 336E LH, 336E LN, 336F L, 345B II, 345C, 345C L, 349E, 349E L, 349E L VG, 349F L, 365B, 365B II, 365B L, 365C, 365C L, 365...
776, 777
RM-250C, RM-350B, RR-250, RR-250B, SM-350, SR118, SR321, SS-250
AD40, AD45, AE40, CS-323C
AP-1055D, AP-650B, AP-655D, BG-225C, BG-245C, BG655D, PR-450
AP-1055D, AP-650B, AP-655D, BG-225C, BG-245C, BG655D, PR-450
AD45, AE40 II
3508B, 3512B, 3516, 3516B, 3516C, 797, 797B, G3516
3512B, 7271, D346, D348, D349, D399, D7F, D7G, D7G2, D8H, G399, RM-250C, RR-250, RR-250B, SS-250
120, 120B, 12E, 1390, 140, 2590, 3512B, 541, 541 2, 551, 552, 552 2, 561B, 561C, 641B, 7211, 7221, 7271, 772, 773, 777, 8 SR, 8A, 992, D10, D348, D5, D5B, D7F, D8H, TK741, TK751, TK752
3182568
BOLT
3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B, 3516C
3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B, 3516C
3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B, 3516C, 5230, 5230B, 776C, 776D, 777, 777B, 777C, 777D, 784B, 784C, 785, 785B, 785C, 785D, 789, 789B, 789C, 789D, 793B, 793C, 793D, 797, 797B, 854G,...
3208, 3304, 3306, 3306B, 3406, 3406B, 3406C, 3408, 3408C, 3412, 3412C, 3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B, 3516C, C15, C175-16, C18, C27, C32, G3306, G3406, G3408, G3408B, G3412, G350...
3304, 3304B, 3306, 3306B, 918F, 933, 933C, 939, 939C, D3C III, D4C III, D5C III, IT12B, IT18F
3304, 3304B, 3306, 3306B, 3406, 3406B, 3406C
215C, 219D, 235, 235B, 235D, 3406B, 3412, 3412C, 3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B, 3516C, 508, 518, 578, 583R, 583T, 587R, 587T, 589, 621G, 623G, 627G, 631G, 637G, 651E, 657E, 657G,...
10 FT, 10-20B, 10B, 235C, 245, 3406B, 3412, 3412C, 3456, 3508, 3508B, 3512, 3512B, 3516, 3516B, 3516C, 515, 517, 525, 527, 561M, 578, 583R, 583T, 587R, 587T, 589, 8 FT, 8-16B, 826C, 834B, 933, 933C, 9...
3508, 3508B, 3512, 3512B, 3512C, 3516, 3516B, 3516C, 615C, 623E, 623F, 623G, 973C, 994, C175-16, C18, D8N, G3516, G3516B, G3516C, G3516H, PM3516, XQC1200
3512, 3512B, 3516B, 793D, 797, 797B, G3516