4532858 BOLT Caterpillar parts
345D L, 349D, 349D L, 365B, 365C, 365C L, 365C L MH, 374D L, 374F L, 385C, 385C FS, 385C L, 390D, 390D L, 390F L
Rating:
Alternative (cross code) number:
CA4532858
453-2858
4532858
CA4532858
453-2858
4532858
Weight: 1 pounds 0 kg.
EXCAVATOR, FRONT SHOVEL,
Compatible equipment models: 4532858:
Number on catalog scheme:
4
For full view, you need register
Information:
Illustration 1 g00435878
Schematic for the Rotary Switch (Transmission Auto/Manual) The two-position transmission auto/manual switch has two inputs to the power train electronic control module (ECM). These inputs are normally open (N/O) and normally closed (N/C). During normal operation, one of the inputs is open and the other input is grounded. If both inputs are the same, the power train ECM detects a fault. Also, this fault is detected when both inputs are either open or shorted to the +battery. Before performing this procedure refer to table 2 in order to determine the connector and the contact that corresponds to the faulty circuit.
Table 1
Auto/Manual Switch Status
Switch Position 973-BR Circuit
(N/O) J1-29 977-YL Circuit
(N/C) J1-31
Auto Open Grounded
Manual Grounded Open Note: Ensure that the desired fault CID 0368 FMI 03 is active.Note: The following procedure can create other faults that the power train ECM detects. Ignore these created faults and clear the created faults when CID 0368 FMI 03 is corrected.
Check for an open circuit.
Turn the disconnect switch and the key start switch to the OFF position.
Disconnect the machine harness from the power train ECM.
At the machine harness connector for the power train ECM, check the continuity to ground of the N/C contact and the N/O contact with the transmission auto/manual switch activated and not activated. Refer to table 2 for the correct continuity combinations.Expected Result: The continuity check does not agree with the information found in table 2.Results:
YES - The continuity check does NOT agree with table 2. The harness or the transmission auto/manual switch is faulty. Proceed to Step 2.
NO - The continuity check agrees with table 2. Proceed to Step 3.
Check the transmission auto/manual switch.
Disconnect the machine harness from the transmission auto/manual switch.
Check the continuity to ground of the N/C contact and the N/O contact with the transmission auto/manual switch activated and not activated. Refer to table 2 for the correct continuity combinations.Expected Result: The continuity check does not agree with the table 2.Results:
YES - The continuity check does not agree with table 2. The transmission auto/manual switch is faulty. Repair the switch or replace the switch.
NO - Continuity check agrees with table 2. Repair the machine harness or replace the machine harness.
Check for a short to the +battery.
At the machine harness connector for the power train ECM, check the continuity from each of the switch contact wires to the contacts J1-1, J1-6, J1-40 and J2-12.Expected Result: Continuity exists between one of the sources of the battery voltage and the switch circuit.Results:
YES - Continuity exists between one of the sources of battery voltage. The machine harness is faulty. Repair the machine harness or replace the machine harness.
NO - Continuity does not exist between one of the sources of battery voltage and the switch circuit. The machine harness is correct. It is unlikely that an power train ECM is faulty. Exit this procedure and perform CID 0368 FMI 03. If the cause is not found, replace the power
Cat SIS web machinery list:
Parts bolt Caterpillar catalog:
320C FM, 320D, 320D FM, 320D FM RR, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 323E L, 324E, 324E L, 324E LN, 329D L, 329E, 329E L, 336E, 336E H, 336E HVG, 336E L, 336E LH, 336E LN, 336F L, 345D L, 349...
324D, 324D L, 324D LN, 324E, 324E L, 324E LN, 325D, 325D L, 326D L, 329D, 329D L, 329D LN, 329E, 329E L, 329E LN, 330C, 330C L, 330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 3...
320B, 320C, 320D, 320D FM, 320D L, 320D2, 320D2 L, 320E, 320E LN, 321C, 322C, 322C FM, 323D L, 323D LN, 323D SA, 323D2 L, 323E L, 324D, 324D FM, 324D L, 324D LN, 324E, 324E L, 324E LN, 325C, 325C FM, ...
16M, 320D, 320D FM, 320D L, 320D2, 320D2 L, 320E, 320E LN, 322C, 323D L, 323D LN, 323D SA, 323D2 L, 323E L, 325C, 325D, 325D FM, 325D L, 328D LCR, 329D, 329D L, 329D LN, 329E, 329E L, 329E LN, 330C, 3...
320C, 325C, 330B L, 330C, 330C FM, 330C L, 330C MH, 330D, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 336E, 336E H, 336E HVG, 336E L, 336E LH, 336E LN, 336F L, 340D L, 340D2 L, 34...
330, 330 FM L, 330 L, 330B, 330B L, 345B II, 345B II MH, 345B L, 349E, 349E L, 349E L HVG, 349E L VG, 349F L, 350, 365B, 365B II, 365B L, 385B, 525C, 525D, 535C, 535D, 545C, 545D, 555D, GSH15, GSH15-6...
320D, 330C L, 330D L, 336D, 336D2, 336E, 336E H, 336E L, 336E LH, 336F L, 345C, 345C L, 345C MH, 345D, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L, 349E L VG, 349F L, 365B, 365B II, 365B L, 365C, 36...
320E LRR, 320E RR, 323E L, 325D L, 328D LCR, 329D, 329D L, 329E, 329E L, 349D, 374D L, 374F L, 390D, 390D L, 390F L
330, 330 FM L, 330 L, 374F L, 390F L, OEMS
345B II, 345C, 345C L, 365B, 365B II, 365B L, 365C, 365C L, 365C L MH, 374D L, 374F L, 385C
345B II, 345C, 345D L, 349D, 349D L, 349E, 349E L, 349E L VG, 349F L
365C, 365C L, 374D L, 374F L, 385C, 385C FS, 385C L, 390D, 390D L
1280822
BOLT
365B
365B
365B, 365B II, 365C, 365C L, 365C L MH
1847213
BOLT
365B
365B
345B L
325B L, 330B L, 330C, 330C L, 330D L, 345B II, 345B L
1921768
BOLT
325B L, 330B L, 330C, 330D L, 345B II, 345B L, 345C L
325B L, 330B L, 330C, 330D L, 345B II, 345B L, 345C L
1778363
BOLT
365B, 365B II, 365B L
365B, 365B II, 365B L
1703645
BOLT
365B
365B
1638685
BOLT-SOCKET HEAD
365B, 365B II, 365B L
365B, 365B II, 365B L
4519261
BOLT
365B, 365C, 365C L, 374F L, 385C, 385C L
365B, 365C, 365C L, 374F L, 385C, 385C L
7L0654
BOLT
365B
365B
4532860
BOLT
365B, 365C, 365C L, 365C L MH, 374D L, 374F L
365B, 365C, 365C L, 365C L MH, 374D L, 374F L