4613876 BOLT Caterpillar parts
Rating:
Alternative (cross code) number:
CA4613876
461-3876
4613876
CA4613876
461-3876
4613876
Information:
Removal Procedure
Disconnect all hoses, tube assemblies, and wire leads from the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Remove" for more information.
Illustration 1 g01245092
Typical example
Illustration 2 g01789673
Tightening sequence for the exhaust manifold
Loosen bolts (4) in reverse numerical order to the sequence that is shown in Illustration 2. Note: Loosening the bolts in reverse numerical order will help prevent distortion of the exhaust manifold.
Remove bolts (4) from exhaust manifold (3). Note: Support the manifold as the bolts are removed.
Remove the assembly of exhaust manifold (3) and the turbocharger.
Remove exhaust manifold gasket (1).
Remove the turbocharger from exhaust manifold (3). Refer to Disassembly and Assembly, "Turbocharger - Remove" for more information.
If necessary, remove studs (2) from exhaust manifold (3). Installation Procedure (Top Mounted Exhaust Manifold)
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Guide Stud
M10 by 100 mm 2
Illustration 3 g01245092
Typical example
Ensure that the exhaust manifold is clean and free from damage. If necessary, replace the exhaust manifold. Clean the gasket surface of the cylinder head.
If necessary, install studs (2) to exhaust manifold (3). Tighten the studs to a torque of 18 N m (13 lb ft).
Illustration 4 g01789677
Tightening sequence for the exhaust manifold
Install Tooling (A) to the cylinder head in Positions (X). Refer to Illustration 4.
Position a new exhaust manifold gasket (1) onto Tooling (A). Note: Ensure that the exhaust manifold gasket is correctly oriented.
Install the tube assembly for the oil drain from the turbocharger to the cylinder block. Refer to Disassembly and Assembly, "Turbocharger - Install" for more information.
Align exhaust manifold (3) with Tooling (A). Install the exhaust manifold to the cylinder head.
Install new bolts (4) finger tight.
Remove Tooling (A). Install remaining bolts (4) finger tight.
Tighten bolts (4) to a torque of 40 N m (30 lb ft) in the sequence that is shown in Illustration 4. End By:
Install the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Install".
Disconnect all hoses, tube assemblies, and wire leads from the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Remove" for more information.
Illustration 1 g01245092
Typical example
Illustration 2 g01789673
Tightening sequence for the exhaust manifold
Loosen bolts (4) in reverse numerical order to the sequence that is shown in Illustration 2. Note: Loosening the bolts in reverse numerical order will help prevent distortion of the exhaust manifold.
Remove bolts (4) from exhaust manifold (3). Note: Support the manifold as the bolts are removed.
Remove the assembly of exhaust manifold (3) and the turbocharger.
Remove exhaust manifold gasket (1).
Remove the turbocharger from exhaust manifold (3). Refer to Disassembly and Assembly, "Turbocharger - Remove" for more information.
If necessary, remove studs (2) from exhaust manifold (3). Installation Procedure (Top Mounted Exhaust Manifold)
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Guide Stud
M10 by 100 mm 2
Illustration 3 g01245092
Typical example
Ensure that the exhaust manifold is clean and free from damage. If necessary, replace the exhaust manifold. Clean the gasket surface of the cylinder head.
If necessary, install studs (2) to exhaust manifold (3). Tighten the studs to a torque of 18 N m (13 lb ft).
Illustration 4 g01789677
Tightening sequence for the exhaust manifold
Install Tooling (A) to the cylinder head in Positions (X). Refer to Illustration 4.
Position a new exhaust manifold gasket (1) onto Tooling (A). Note: Ensure that the exhaust manifold gasket is correctly oriented.
Install the tube assembly for the oil drain from the turbocharger to the cylinder block. Refer to Disassembly and Assembly, "Turbocharger - Install" for more information.
Align exhaust manifold (3) with Tooling (A). Install the exhaust manifold to the cylinder head.
Install new bolts (4) finger tight.
Remove Tooling (A). Install remaining bolts (4) finger tight.
Tighten bolts (4) to a torque of 40 N m (30 lb ft) in the sequence that is shown in Illustration 4. End By:
Install the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Install".
Cat SIS web machinery list:
Parts bolt Caterpillar catalog:
4602453
BOLT
Caterpillar
Caterpillar
4586792
BOLT
Caterpillar
Caterpillar
4578759
BOLT
Caterpillar
Caterpillar
4578757
BOLT
Caterpillar
Caterpillar
4578672
BOLT
Caterpillar
Caterpillar
4575513
BOLT-12 POINT HEAD
Caterpillar
Caterpillar
4696703
BOLT-HEAD
Caterpillar
Caterpillar
4636062
BOLT
Caterpillar
Caterpillar
4613886
BOLT
Caterpillar
Caterpillar
4613884
BOLT
Caterpillar
Caterpillar
4613882
BOLT
Caterpillar
Caterpillar
4613878
BOLT
Caterpillar
Caterpillar