5I5005 BOLT Caterpillar parts
303.5C, 303.5D, 303C CR, 304C CR, 304D CR, 305.5D, 305C CR, 305D CR, 311B, 311C, 311D LRR, 312B, 312C, 312C L, 312D, 312D L, 313D, 314C, 314D CR, 314D LCR, 315D L, 318C, 318D L, 319C, 319D, 319D L, 31...
Rating:
Alternative (cross code) number:
CA5I5005
5I-5005
5I5005
CA5I5005
5I-5005
5I5005
Weight: 0.08 pounds 0 kg.
COMPACT WHEEL LOADER, MOBILE HYD POWER UNIT,
Compatible equipment models: 5I5005:
Number on catalog scheme:
1
For full view, you need register
Information:
General
The following disassembly and assembly procedure is presented for reference purposes and presupposes that a major rebuild of the compressor is being undertaken. Several maintenance kits are available which do not require full disassembly. When servicing this compressor with a maintenance kit all components contained in the kit must be used. The instructions provided with these parts and kits should be followed in lieu of the instructions presented here.Removal
These instructions are general and are intended to be a guide, in some cases additional preparations and precautions are necessary.1. Block the wheels of the vehicle and drain the air pressure from all the reservoirs in the system.2. Drain the engine cooling system and the cylinder head of the compressor. Identify and disconnect all air, water and oil lines leading to the compressor.3. Remove the governor and any supporting brackets attached to the compressor and note their positions on the compressor to aid in reassembly.4. Remove the discharge and inlet fittings, if applicable, and note their position on the compressor to aid in reassembly.5. Remove the flange or base mounting bolts and remove the compressor from the vehicle.6. Remove the drive gear(s) or pulley from the compressor crankshaft using a gear puller. Inspect the pulley or gear and associated parts for visible wear or damage. Since these parts are precision fitted, they must be replaced if they are worn or damaged.Preparation For Disassembly
Remove road dirt and grease from the exterior of the compressor with a cleaning solvent. Before the compressor is disassembled, the following items should be marked to show their relationship when the compressor is assembled. Mark the rear end cover in relation to the crankcase. Mark the base plate or base adapter in relation to the crankcase.A convenient method to indicate the above relationships is to use a metal scribe to mark the parts with numbers or lines. Do not use marking methods such as chalk that can be wiped off or obliterated during rebuilding.Cylinder Head
Remove six cylinder head cap screws (1) and tap the head with a soft mallet to break the gasket seal. Remove unloader cover plate cap screws (2), lockwashers (3) and unloader cover plate (4). Scrape off any gasket material (5) from the cover plate, cylinder head and crankcase.1. Remove unloader pistons (7), O-rings (6) and springs (8).2. Inspect unloader piston bushings (9) for nicks, wear, corrosion and scoring. It is recommended that the compressor be replaced if it is determined that the unloader bushing is damaged or worn excessively.Before disassembling the discharge valve mechanism, measure and record the discharge valve travel (from closed to completely open).3. If the measured discharge valve travel EXCEEDS 11.68 mm (.046 in), the compressor should be replaced. If the discharge valve travel does not exceed 11.68 mm (.046 in), using a 9/16 inch hex wrench, remove discharge valve seats (18), valves (17) and valve springs (16).4. Remove inlet valve stops (14), valves (17), valve seats (11), valve springs (12) and gaskets (10). It is recommended that a tool
The following disassembly and assembly procedure is presented for reference purposes and presupposes that a major rebuild of the compressor is being undertaken. Several maintenance kits are available which do not require full disassembly. When servicing this compressor with a maintenance kit all components contained in the kit must be used. The instructions provided with these parts and kits should be followed in lieu of the instructions presented here.Removal
These instructions are general and are intended to be a guide, in some cases additional preparations and precautions are necessary.1. Block the wheels of the vehicle and drain the air pressure from all the reservoirs in the system.2. Drain the engine cooling system and the cylinder head of the compressor. Identify and disconnect all air, water and oil lines leading to the compressor.3. Remove the governor and any supporting brackets attached to the compressor and note their positions on the compressor to aid in reassembly.4. Remove the discharge and inlet fittings, if applicable, and note their position on the compressor to aid in reassembly.5. Remove the flange or base mounting bolts and remove the compressor from the vehicle.6. Remove the drive gear(s) or pulley from the compressor crankshaft using a gear puller. Inspect the pulley or gear and associated parts for visible wear or damage. Since these parts are precision fitted, they must be replaced if they are worn or damaged.Preparation For Disassembly
Remove road dirt and grease from the exterior of the compressor with a cleaning solvent. Before the compressor is disassembled, the following items should be marked to show their relationship when the compressor is assembled. Mark the rear end cover in relation to the crankcase. Mark the base plate or base adapter in relation to the crankcase.A convenient method to indicate the above relationships is to use a metal scribe to mark the parts with numbers or lines. Do not use marking methods such as chalk that can be wiped off or obliterated during rebuilding.Cylinder Head
Remove six cylinder head cap screws (1) and tap the head with a soft mallet to break the gasket seal. Remove unloader cover plate cap screws (2), lockwashers (3) and unloader cover plate (4). Scrape off any gasket material (5) from the cover plate, cylinder head and crankcase.1. Remove unloader pistons (7), O-rings (6) and springs (8).2. Inspect unloader piston bushings (9) for nicks, wear, corrosion and scoring. It is recommended that the compressor be replaced if it is determined that the unloader bushing is damaged or worn excessively.Before disassembling the discharge valve mechanism, measure and record the discharge valve travel (from closed to completely open).3. If the measured discharge valve travel EXCEEDS 11.68 mm (.046 in), the compressor should be replaced. If the discharge valve travel does not exceed 11.68 mm (.046 in), using a 9/16 inch hex wrench, remove discharge valve seats (18), valves (17) and valve springs (16).4. Remove inlet valve stops (14), valves (17), valve seats (11), valve springs (12) and gaskets (10). It is recommended that a tool
Cat SIS web machinery list:
Parts bolt Caterpillar catalog:
1390, 2484C, 2590, 320 L, 320B, 320C, 320D, 320D FM, 320D2, 320D2 L, 320N, 322 FM L, 322 LN, 322B, 322B L, 322B LN, 322C, 322C FM, 323D L, 323D LN, 323D SA, 324D, 324D FM, 324D FM LL, 324D L, 324D LN,...
320C, 938H, D6N, D7H, D8N
320C FM, 320D, 320D FM, 320D FM RR, 320D L, 322C, 322C FM, 324D FM, 325C FM, 325D FM, 325D FM LL, 325D MH, 330B L, 330C, 330C FM, 330C L, 330D FM, 330D MH, 345B II, 345B L, 345C, 345C L, 345C MH, 365B...
320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 321D LCR, 322B L, 322B LN, 322C, 322C FM, 323D L, 323D LN, 3...
320C FM, 322B L, 322C, 322C FM, 325B L, 325C, 325C FM, 330B L, 330C FM, 330C L, 330C MH, 345B, 345B II, 345B II MH, 5110B, BA18, D25C, D30C, D350C, M325B, W330B, W345B II
320C FM, 320D, 320D FM, 320D FM RR, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 323E L, 324E, 324E L, 324E LN, 329D L, 329E, 329E L, 336E, 336E H, 336E HVG, 336E L, 336E LH, 336E LN, 336F L, 345D L, 349...
320B, 320C, 320D, 320D FM, 320D L, 320D2, 320D2 L, 320E, 320E LN, 321C, 322C, 322C FM, 323D L, 323D LN, 323D SA, 323D2 L, 323E L, 324D, 324D FM, 324D L, 324D LN, 324E, 324E L, 324E LN, 325C, 325C FM, ...
320C, 320C FM, 320D, 320D FM, 320D FM RR, 322C, 322C FM, 323D LN, 323D SA, 323E L, 324D, 324D L, 324D LN, 324E, 324E L, 324E LN, 325C, 325C FM, 325D, 325D L, 325D MH, 326D L, 329D, 329D L, 329D LN, 32...
16M, 320D, 320D FM, 320D L, 320D2, 320D2 L, 320E, 320E LN, 322C, 323D L, 323D LN, 323D SA, 323D2 L, 323E L, 325C, 325D, 325D FM, 325D L, 328D LCR, 329D, 329D L, 329D LN, 329E, 329E L, 329E LN, 330C, 3...
320C, 325C, 330B L, 330C, 330C FM, 330C L, 330C MH, 330D, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 336E, 336E H, 336E HVG, 336E L, 336E LH, 336E LN, 336F L, 340D L, 340D2 L, 34...
320C, 320C FM, 320C L, 320D, 320D FM, 320D GC, 320D L, 320D LRR, 320D RR, 321C, 321D LCR, 323D L
1090, 2290, 320D, 320D FM, 322C FM, 324D FM, 324D FM LL, 325C, 325D, 325D L, 329D, 329D L, 329D LN, 329E, 329E L, 329E LN, 336E, 345C, 511, OEMS, TK711
311, 311B, 311C, 312, 312B, 312C, 312C L, 314C, 318C, 319C, 320 L, 320B, 320B L, 320C, 320C FM, 320C L, 320D, 320D LRR, 321C, 323D L, 323D LN
0947741
BOLT-BEARING CAP
311C, 311D LRR, 312C, 312C L, 312D, 312D L, 313D, 314C, 314D CR, 314D LCR, 315D L, 318C, 318D L, 319C, 319D, 319D L, 319D LN, 320B, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 3...
311C, 311D LRR, 312C, 312C L, 312D, 312D L, 313D, 314C, 314D CR, 314D LCR, 315D L, 318C, 318D L, 319C, 319D, 319D L, 319D LN, 320B, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 3...
307C, 307D, 311C, 311D LRR, 311F LRR, 312C L, 312D, 312D L, 315C, 315D L, 318C, 319D L, 319D LN, 320C, 320C FM, 320C L, 320D, 320D FM, 320D L, 320D LRR, 320D RR, 320D2, 320D2 L, 322C, 322C FM, 323D L,...
2325264
BOLT
307C, 307D, 308C, 308D
307C, 307D, 308C, 308D
307C, 307D, 311C, 311D LRR, 311F LRR, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 313D, 313D2, 313D2 LGP, 315C, 315D L, 318C, 318D L, 318D2 L, 319D, 319D L, 320C, 320C L, 320D, 320D FM, 320D GC, 3...
1761985
BOLT AS
307C, 320C FM
307C, 320C FM
305.5E, 311D LRR, 312C, 312C L, 312D, 312D L, 313D, 314D CR, 314D LCR, 315C, 315D L, 318C, 318D L, 319C, 319D, 319D L, 319D LN, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D ...
307, 311, 311B, 311C, 311D LRR, 312B, 312C, 312C L, 312D, 312D L, 313D, 314C, 314D CR, 314D LCR, 315D L, 318C, 318D L, 319C, 319D, 319D L, 319D LN, 320 L, 320B, 320C, 320C FM, 320C L, 320D, 320D FM, 3...
5I7663
BOLT
311, 311B, 311C, 311D LRR, 312B, 312C, 312C L, 312D, 312D L, 313D, 314C, 314D CR, 314D LCR, 315D L, 318D L, 319D, 319D L, 319D LN, 320 L, 320B, 320B L, 320B U, 320N, 321B
311, 311B, 311C, 311D LRR, 312B, 312C, 312C L, 312D, 312D L, 313D, 314C, 314D CR, 314D LCR, 315D L, 318D L, 319D, 319D L, 319D LN, 320 L, 320B, 320B L, 320B U, 320N, 321B
311C, 312C, 312C L, 314C, 318C, 319C, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 321C, 321D LCR, 323D L, 323D LN, 323D SA
311, 311B, 311C, 311D LRR, 312, 312B, 312C, 312C L, 312D, 312D L, 313D, 314C, 314D CR, 314D LCR, 315D L, 318D L, 319D, 319D L, 319D LN
5I7610
BOLT
311, 311B, 311C, 311D LRR, 312, 312B, 312C, 312C L, 312D, 312D L, 313D, 314C, 314D CR, 314D LCR, 315D L, 318C, 318D L, 319C, 319D, 319D L, 319D LN, 320, 320 L, 320B, 320B FM LL, 320C, 320C FM, 320C L,...
311, 311B, 311C, 311D LRR, 312, 312B, 312C, 312C L, 312D, 312D L, 313D, 314C, 314D CR, 314D LCR, 315D L, 318C, 318D L, 319C, 319D, 319D L, 319D LN, 320, 320 L, 320B, 320B FM LL, 320C, 320C FM, 320C L,...