5I7610 BOLT Caterpillar parts
311, 311B, 311C, 311D LRR, 312, 312B, 312C, 312C L, 312D, 312D L, 313D, 314C, 314D CR, 314D LCR, 315D L, 318C, 318D L, 319C, 319D, 319D L, 319D LN, 320, 320 L, 320B, 320B FM LL, 320C, 320C FM, 320C L,...
Rating:
Alternative (cross code) number:
CA5I7610
5I-7610
5I7610
CA5I7610
5I-7610
5I7610
Weight: 0.01 pounds 0 kg.
EXCAVATOR, MOBILE HYD POWER UNIT,
Compatible equipment models: 5I7610:
Number on catalog scheme:
9A
For full view, you need register
Information:
All ECM Except 106-4458
As mentioned earlier in this publication, the transmission configuration code must be programmed into the transmission ECM. This will need to be done if a new transmission ECM is installed or if a transmission ECM is used from another machine.
(1) Transmission indicator lamp.
(2) Diagnostic plug. (3) ECM. (Cover Has Been Removed.)1. Remove sheet metal panel covering the transmission ECM (3).2. Locate the transmission indicator lamp (1) located in front of the steering wheel.3. Place the Start/Stop Key Switch in the Run position with engine off.4. Uncouple the diagnostic plug (2).5. Determine the right transmission configuration code from Chart 5 for the model of motor grader the control is installed on. (For illustration purposes, assume that the model is a 140H. Therefore the transmission configuration code would be "41".6. Jumper Sockets 1,2 and 3 on the diagnostic receptacle. Place the transmission control lever in the gear (Forward or Reverse) which corresponds to the first digit of the desired transmission configuration code. The first digit must be programmed using the forward transmission control lever. For this example, place the transmission control lever in Fourth Forward. Wait until the transmission indicator lamp (1) flashes out this digit. Place the transmission control lever in the neutral position. Remove jumpers completely out of the diagnostic receptacle. The first digit is programmed.7. Jumper Sockets 1,2 and 4 on the diagnostic receptacle. Place the transmission control lever in the gear (Forward or Reverse) which corresponds to the second digit of the desired transmission configuration code. The second digit must be programmed using the reverse transmission control lever. For this example, place the transmission control lever in First Reverse. Wait until the transmission indicator lamp (1) flashes out this digit. Place the transmission control lever in the neutral position. Remove jumpers completely out of the diagnostic receptacle. The second digit is programmed.8. Replace the diagnostic receptacle. Turn the Start/Stop Key Switch to the OFF position.9. Turn the Start/Stop Key Switch to the ON position. Watch the transmission indicator lamp (1). Make sure that it flashes out the desired transmission configuration code. In our example, you should see a "41" flash code displayed on power up.Troubleshooting
Troubleshooting Without An ECAP Or ECM Diagnostics
Operate the machine in each direction and in all speeds. Note the noises that are not normal and find their source. If the operation is not correct, refer to the following problems and procedures.The following procedure has been designed without the benefit of using diagnostics from the transmission ECM. However, using an ECAP in combination with this troubleshooting guide should improve the efficiency in resolving the problem. Problem:Motor Grader Will Not Key Start/Stop Corrective Procedure:1. Check the transmission control fuse (10 amp) located in fuse panel at the base of the steering console. Replace if necessary.2. Remove the transmission ECM from under the seat and disconnect the 40-pin Deutch® connector. Measure voltage between Pins 1 and 2.3. If voltage measured in Step 2 is above 20 DCV, the transmission ECM is inoperative. If
As mentioned earlier in this publication, the transmission configuration code must be programmed into the transmission ECM. This will need to be done if a new transmission ECM is installed or if a transmission ECM is used from another machine.
(1) Transmission indicator lamp.
(2) Diagnostic plug. (3) ECM. (Cover Has Been Removed.)1. Remove sheet metal panel covering the transmission ECM (3).2. Locate the transmission indicator lamp (1) located in front of the steering wheel.3. Place the Start/Stop Key Switch in the Run position with engine off.4. Uncouple the diagnostic plug (2).5. Determine the right transmission configuration code from Chart 5 for the model of motor grader the control is installed on. (For illustration purposes, assume that the model is a 140H. Therefore the transmission configuration code would be "41".6. Jumper Sockets 1,2 and 3 on the diagnostic receptacle. Place the transmission control lever in the gear (Forward or Reverse) which corresponds to the first digit of the desired transmission configuration code. The first digit must be programmed using the forward transmission control lever. For this example, place the transmission control lever in Fourth Forward. Wait until the transmission indicator lamp (1) flashes out this digit. Place the transmission control lever in the neutral position. Remove jumpers completely out of the diagnostic receptacle. The first digit is programmed.7. Jumper Sockets 1,2 and 4 on the diagnostic receptacle. Place the transmission control lever in the gear (Forward or Reverse) which corresponds to the second digit of the desired transmission configuration code. The second digit must be programmed using the reverse transmission control lever. For this example, place the transmission control lever in First Reverse. Wait until the transmission indicator lamp (1) flashes out this digit. Place the transmission control lever in the neutral position. Remove jumpers completely out of the diagnostic receptacle. The second digit is programmed.8. Replace the diagnostic receptacle. Turn the Start/Stop Key Switch to the OFF position.9. Turn the Start/Stop Key Switch to the ON position. Watch the transmission indicator lamp (1). Make sure that it flashes out the desired transmission configuration code. In our example, you should see a "41" flash code displayed on power up.Troubleshooting
Troubleshooting Without An ECAP Or ECM Diagnostics
Operate the machine in each direction and in all speeds. Note the noises that are not normal and find their source. If the operation is not correct, refer to the following problems and procedures.The following procedure has been designed without the benefit of using diagnostics from the transmission ECM. However, using an ECAP in combination with this troubleshooting guide should improve the efficiency in resolving the problem. Problem:Motor Grader Will Not Key Start/Stop Corrective Procedure:1. Check the transmission control fuse (10 amp) located in fuse panel at the base of the steering console. Replace if necessary.2. Remove the transmission ECM from under the seat and disconnect the 40-pin Deutch® connector. Measure voltage between Pins 1 and 2.3. If voltage measured in Step 2 is above 20 DCV, the transmission ECM is inoperative. If
Cat SIS web machinery list:
Parts bolt Caterpillar catalog:
320C, 938H, D6N, D7H, D8N
320C FM, 320D, 320D FM, 320D FM RR, 320D L, 322C, 322C FM, 324D FM, 325C FM, 325D FM, 325D FM LL, 325D MH, 330B L, 330C, 330C FM, 330C L, 330D FM, 330D MH, 345B II, 345B L, 345C, 345C L, 345C MH, 365B...
320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 321D LCR, 322B L, 322B LN, 322C, 322C FM, 323D L, 323D LN, 3...
320C FM, 322B L, 322C, 322C FM, 325B L, 325C, 325C FM, 330B L, 330C FM, 330C L, 330C MH, 345B, 345B II, 345B II MH, 5110B, BA18, D25C, D30C, D350C, M325B, W330B, W345B II
320B FM LL, 322B L, 325B L, 325C, 330B L, 330D MH, 345B II, 345C, 345C L, 345C MH, 365B, 365B II, 365B L, 365C, 365C L, 365C L MH, 374D L, 374F L, 375, 375 L, 385B, 385C, 385C FS, 385C L, 385C L MH, 3...
320C FM, 320D, 320D FM, 320D FM RR, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 323E L, 324E, 324E L, 324E LN, 329D L, 329E, 329E L, 336E, 336E H, 336E HVG, 336E L, 336E LH, 336E LN, 336F L, 345D L, 349...
320B, 320C, 320D, 320D FM, 320D L, 320D2, 320D2 L, 320E, 320E LN, 321C, 322C, 322C FM, 323D L, 323D LN, 323D SA, 323D2 L, 323E L, 324D, 324D FM, 324D L, 324D LN, 324E, 324E L, 324E LN, 325C, 325C FM, ...
320C, 320C FM, 320D, 320D FM, 320D FM RR, 322C, 322C FM, 323D LN, 323D SA, 323E L, 324D, 324D L, 324D LN, 324E, 324E L, 324E LN, 325C, 325C FM, 325D, 325D L, 325D MH, 326D L, 329D, 329D L, 329D LN, 32...
16M, 320D, 320D FM, 320D L, 320D2, 320D2 L, 320E, 320E LN, 322C, 323D L, 323D LN, 323D SA, 323D2 L, 323E L, 325C, 325D, 325D FM, 325D L, 328D LCR, 329D, 329D L, 329D LN, 329E, 329E L, 329E LN, 330C, 3...
320C, 325C, 330B L, 330C, 330C FM, 330C L, 330C MH, 330D, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 336E, 336E H, 336E HVG, 336E L, 336E LH, 336E LN, 336F L, 340D L, 340D2 L, 34...
320C, 320C FM, 320C L, 320D, 320D FM, 320D GC, 320D L, 320D LRR, 320D RR, 321C, 321D LCR, 323D L
1090, 2290, 320D, 320D FM, 322C FM, 324D FM, 324D FM LL, 325C, 325D, 325D L, 329D, 329D L, 329D LN, 329E, 329E L, 329E LN, 336E, 345C, 511, OEMS, TK711
5I5005
BOLT
303.5C, 303.5D, 303C CR, 304C CR, 304D CR, 305.5D, 305C CR, 305D CR, 311B, 311C, 311D LRR, 312B, 312C, 312C L, 312D, 312D L, 313D, 314C, 314D CR, 314D LCR, 315D L, 318C, 318D L, 319C, 319D, 319D L, 31...
303.5C, 303.5D, 303C CR, 304C CR, 304D CR, 305.5D, 305C CR, 305D CR, 311B, 311C, 311D LRR, 312B, 312C, 312C L, 312D, 312D L, 313D, 314C, 314D CR, 314D LCR, 315D L, 318C, 318D L, 319C, 319D, 319D L, 31...
311, 311B, 311C, 312, 312B, 312C, 312C L, 314C, 318C, 319C, 320 L, 320B, 320B L, 320C, 320C FM, 320C L, 320D, 320D LRR, 321C, 323D L, 323D LN
0947741
BOLT-BEARING CAP
311C, 311D LRR, 312C, 312C L, 312D, 312D L, 313D, 314C, 314D CR, 314D LCR, 315D L, 318C, 318D L, 319C, 319D, 319D L, 319D LN, 320B, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 3...
311C, 311D LRR, 312C, 312C L, 312D, 312D L, 313D, 314C, 314D CR, 314D LCR, 315D L, 318C, 318D L, 319C, 319D, 319D L, 319D LN, 320B, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 3...
307C, 307D, 311C, 311D LRR, 311F LRR, 312C L, 312D, 312D L, 315C, 315D L, 318C, 319D L, 319D LN, 320C, 320C FM, 320C L, 320D, 320D FM, 320D L, 320D LRR, 320D RR, 320D2, 320D2 L, 322C, 322C FM, 323D L,...
2325264
BOLT
307C, 307D, 308C, 308D
307C, 307D, 308C, 308D
307C, 307D, 311C, 311D LRR, 311F LRR, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 313D, 313D2, 313D2 LGP, 315C, 315D L, 318C, 318D L, 318D2 L, 319D, 319D L, 320C, 320C L, 320D, 320D FM, 320D GC, 3...
5I4921
BOLT
311, 311B, 311C, 312B, 312C, 312C L, 314C, 318C, 319C, 320 L, 320B, 320C, 320C FM, 320C L, 320D, 320D LRR, 320N, 321C, 323D L, 323D LN, E110B, E120B, E200B
311, 311B, 311C, 312B, 312C, 312C L, 314C, 318C, 319C, 320 L, 320B, 320C, 320C FM, 320C L, 320D, 320D LRR, 320N, 321C, 323D L, 323D LN, E110B, E120B, E200B
305.5E, 311D LRR, 312C, 312C L, 312D, 312D L, 313D, 314D CR, 314D LCR, 315C, 315D L, 318C, 318D L, 319C, 319D, 319D L, 319D LN, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D ...
307, 311, 311B, 311C, 311D LRR, 312B, 312C, 312C L, 312D, 312D L, 313D, 314C, 314D CR, 314D LCR, 315D L, 318C, 318D L, 319C, 319D, 319D L, 319D LN, 320 L, 320B, 320C, 320C FM, 320C L, 320D, 320D FM, 3...
5I7663
BOLT
311, 311B, 311C, 311D LRR, 312B, 312C, 312C L, 312D, 312D L, 313D, 314C, 314D CR, 314D LCR, 315D L, 318D L, 319D, 319D L, 319D LN, 320 L, 320B, 320B L, 320B U, 320N, 321B
311, 311B, 311C, 311D LRR, 312B, 312C, 312C L, 312D, 312D L, 313D, 314C, 314D CR, 314D LCR, 315D L, 318D L, 319D, 319D L, 319D LN, 320 L, 320B, 320B L, 320B U, 320N, 321B
311C, 312C, 312C L, 314C, 318C, 319C, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 321C, 321D LCR, 323D L, 323D LN, 323D SA
311, 311B, 311C, 311D LRR, 312, 312B, 312C, 312C L, 312D, 312D L, 313D, 314C, 314D CR, 314D LCR, 315D L, 318D L, 319D, 319D L, 319D LN